Quoizel PCSL1616C User Manual
Assembly Instruction Sheet #IS-PCSL1616C
For Style PCSL1616C
Quoizel, Inc.
6 Corporate Parkway
Goose Creek, SC 29445
Customer Service
Phone 631.273.2700
Fax 631.231.7102
www.quoizel.com
ToolsRequired: Flatheadscrewdriver, Phillipsscrewdriver,pliers,wire cutters, wire strippers, electricaltape,
safetyglasses.
BulbRecommended:
EstimatedAssembly Time:
Preparation:
belowto be sure all partsarepresent. If any parts aremissing or damaged, do not attemptto assemble, install, or
operatethe fixture. Contact customer serviceforreplacement parts.
Identifyand inspect all parts beforebeginninginstallation. Check package content listand diagrams
(3)Medium Base 60W bulbs Maximum,Alternate bulb (3) 13WCFLMaximum.
20-30minutes
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Package Contents
Ceiling Canopy
A
x1
Shade
B
x1
against the Crossbar (AA) to secure in place.
D. Thread another Hex Nut (CC) onto the end of the Nipple (DD).
Thread this Hex Nut (CC) on just enough so the inside surface of the
Ceiling Canopy (A) rests against it. * You may have to trial fit the
Ceiling Canopy (A) one more times to insure this distance also. This
Hex Nut (CC) is needed here to prevent you from crushing down the
center of the Ceiling Canopy (A).
E. Refer to Step 3 for wire connections.
F. Attach the Ceiling Canopy (A) over the end of the Nipple (DD) and
secure with the Mounting Ball (EE). Hand tighten until snug.
Crossbar
AA
x1
Lock Washer
BB
x1
Hex Nut
CC
x2
STEP 1 Install Crossbar-
A. AA)Attach the Crossbar ( to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included) Tighten until snug..
Figure 1
Green Ground Screw
STEP 2 Install Nipple to Crossbar-
* Pliers is required for this step.
A. Thread one Hex Nut (CC) to the middle of the Nipple (DD). Place the
Lock Washer (BB) over the Nipple (DD) and then thread the Nipple
(DD) into the Crossbar (AA) until the Nipple (DD) is about 0.375”
above the Crossbar (AA).
B. Position the center hole of the Ceiling Canopy (A) over the end of
the Nipple (DD).Adjust the Nipple (DD) so approx 0.375” of the
Nipple (DD) is protruding from the mounting hole on the Ceiling
Canopy (A). This adjustment may take a few tries.
C. Remove the Ceiling Canopy (A) and then tighten the Hex Nut (CC)
Hardware Contents
Nipple
DD
x1
Mounting Ball
EE
x1
Outlet Box
AA
Outlet Box Screw
(not included)
BB
AA
Figure 2
STEP 3 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Strip and
prepare wire ends according to instructions supplied with
connectors.
B. Connect White Supply Wire from the Outlet Box to Ribbed side Wire
from fixture.
C. Connect Black (or Red) Supply Wire from the Outlet Box to Smooth
side Wire from fixture.
D. Connect Ground Wire from the Outlet Box to Ground Wire from
fixture.
White wire
from supply
Black wire from
supply (or Red)
Ground wire
from supply
DD
CC
EE
Figure 3
Step A
CC
Step D
A
Ribbed side wire
from fixture
Smooth side wire
from fixture
Ground wire
from fixture
2014 QuoizelInc.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
1of2
January2014
E. Twist connectors until wires are tightly joined together.
F. Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
STEP 4 - Install Bulb
A. This fixture uses standard bulb with medium base. Maximum 60
watts.
B. Insert bulb and screw snugly into place.
STEP 5 - Install Shade
A. Insert the Shade (B) into the fixed Tabs on the side of the Ceiling
Canopy (A) first and then pull the Tab with Spring to secure the
Shade (B).
Your fixture is now assembled and ready to use. Enjoy!
A
Spring
Tab
Figure 4
PCSL1616C
FINISH: POLISHED CHROME
(3) 60W
NO.
1
Medium
Base
Bulbs
(Not Supplied)
PART NUMBER
G3818SH
ETCHED GLASS SHADE PAINTED WHITE INSIDE
Bulb
TWO LIGHTS SHOWN FOR ILLUSTRATION PURPOSE ONLY.
Figure 5
1
15.5” Dia.
16.5” Dia.
NOTE: ALL DIMENSIONS ARE ROUNDED UPTO THE NEAREST 1/2"
REPLACEMENT PART DESCRIPTION
REQ.
1
B
4.5”
3”
2014 QuoizelInc.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
2of2
January2014
Loading...