Quoizel PCBV1613C User Manual

Assembly Instruction Sheet #IS-PCBV1613C

For Style PCBV1613C

Quoizel, Inc. 6 Corporate Parkway Goose Creek, SC 29445

Customer Service Phone 631.273.2700 Fax 631.231.7102 www.quoizel.com

ToolsRequired: Flatheadscrewdriver, Phillipsscrewdriver,pliers,wire cutters, wire strippers, electricaltape, safetyglasses.

BulbRecommended: EstimatedAssembly Time: Preparation:

belowto be sure all partsarepresent. If any parts aremissing or damaged, do not attemptto assemble, install, or operatethe fixture. Contact customer serviceforreplacement parts.

Identifyand inspect all parts beforebeginninginstallation. Check package content listand diagrams

(2)Medium Base 60W bulbs Maximum,Alternate bulb (2) 13WCFLMaximum.

20-30minutes

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject glass parts to any shock while in operation or shattering may result.

Package Contents

Lock Washer

Hex Nut

Ceiling

Canopy x1

Shade

Crossbar x1

Ring

Lock Screw

Knurled Nut x3

Bushing x3

Rubber Washer x3

Lock Ring x3

Hardware Contents

Nipple

Mounting Ball

Finial x3

STEP 2 Install Crossbar-

A. AA)Attach the Crossbar ( to the Outlet Box with the head of the

Green Ground Screw facing you. Secure it with Outlet Box Screws (not included) Tighten until snug..

Outlet Box

Figure 2

Green Ground Screw

STEP 3 Install Nipple to Crossbar-

* Pliers is required for this step.

A. Thread one Hex Nut (CC) to the middle of the Nipple (DD). Place the

Lock Washer (BB) over the Nipple (DD) and then thread the Nipple (DD) into the Crossbar (AA) until the Nipple (DD) is about 0.375” above the Crossbar (AA).

B. Position the center hole of the Ceiling Canopy (A) over the end of

the Nipple (DD).Adjust the Nipple (DD) so approx 0.375” of the Nipple (DD) is protruding from the mounting hole on the Ceiling Canopy (A). This adjustment may take a few tries.

C. Remove the Ceiling Canopy (A) and then tighten the Hex Nut (CC)

against the Crossbar (AA) to secure in place.

D. Thread another Hex Nut (CC) onto the end of the Nipple (DD).

Thread this Hex Nut (CC) on just enough so the inside surface of the Ceiling Canopy (A) rests against it. * You may have to trial fit the Ceiling Canopy (A) one more times to insure this distance also. This

Outlet Box Screw (not included)

STEP 1 Install Crossbar-

A. Attach the Lock Screw (C) from the top of the Ceiling Canopy (A).

Place the (D), the Bushing (E), the Ring (B) and the Rubber Washer Secure them together with the Lock Ring (G). Tighten until snug.

Figure 1

2014 QuoizelInc.

Knurled Nut

(F) over the end of the Lock Screws (C) in turn.

Thank you for purchasing a Quoizel product.

Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700

or visit us on-line at www.quoizel.com

1of2

Figure 3

Step A

Step D

January2014

Hex Nut (CC) is needed here to prevent you from crushing down the

center of the Ceiling Canopy (A). E. Refer to Step 4 for wire connections. F. Attach the Ceiling Canopy (A) over the end of the Nipple (DD) and

secure with the Mounting Ball (EE). Hand tighten until snug.

STEP 4 - Wire Connections

A. Use standard wire connectors (not included) to make all wire

connections. (Connectors are not included with fixture.) Strip and prepare wire ends according to instructions supplied with connectors.

B. Connect White Supply Wire from the Outlet Box to Ribbed side Wire

from fixture.

C. Connect Black (or Red) Supply Wire from the Outlet Box to Smooth

side Wire from fixture.

D. Connect Ground Wire from the Outlet Box to Ground Wire from

fixture. E. Twist connectors until wires are tightly joined together. F. Wrap each connection with approved electrical tape and carefully

stuff all the connected wires into the Outlet Box.

STEP 5 - Install Bulb

A. This fixture uses standard bulb with medium base. Maximum 60

watts.

B. Insert bulb and screw snugly into place.

Figure 5

Bulb

STEP 6 - Install Shade

A. Attach the Shade (H) onto the Ring (B) and secure by threading the

Finial (I) onto the Lock Screw (C). Tighten gently until snug.

Your fixture is now assembled and ready to use. Enjoy!

White wire

from supply

Black wire from supply (or Red)

Ground wire

from supply

PCBV1613C

FINISH: POLISHED CHROME

Base

Medium

Bulbs

(2) 60W

(Not Supplied)

PART NUMBER

NO.

G3815MR

G3814SH

MIRROR GLASS 12.5"D

SHADE ETCHED PAINTED INSIDE GLASS

Ribbed side wire from fixture

Smooth side wire from fixture

Ground wire from fixture

Figure 6

Figure 4

ONE LIGHT SHOWN FOR ILLUSTRATION PURPOSE ONLY.

8.5” Dia.

10” Dia.

12.5” Dia.

NOTE: ALL DIMENSIONS ARE ROUNDED UPTO THE NEAREST 1/2"

REPLACEMENT PART DESCRIPTION

REQ.

4.5” 1

2”

2014 QuoizelInc.

Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700

Thank you for purchasing a Quoizel product.

or visit us on-line at www.quoizel.com

2of2

January2014