Quoizel PCAT1617C User Manual

Assembly Instruction Sheet #IS-PCAT1617C

For Style PCAT1617C

Quoizel, Inc.
6 Corporate Parkway
Goose Creek, SC 29445

Customer Service
Phone [phone]
Fax [phone]
www.quoizel.com

ToolsRequired: Flatheadscrewdriver, Phillipsscrewdriver,pliers,wire cutters, wire strippers, electricaltape,
safetyglasses.

BulbRecommended:
EstimatedAssembly Time:
Preparation:

belowto be sure all partsarepresent. If any parts aremissing or damaged, do not attemptto assemble, install, or
operatethe fixture. Contact customer serviceforreplacement parts.

Identifyand inspect all parts beforebeginninginstallation. Check package content listand diagrams

(3)Medium Base 60W bulbs Maximum,Alternate bulb (3) 13WCFLMaximum.

20-30minutes

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.

Package Contents

Big Ring

B

x1

Lock Screw

D

x3

Rubber Washer

F

x9

AA

Lock Washer

BB

x1

Hex Nut

CC

x2

2014 QuoizelInc.

Ceiling Canopy

A

x1

Small Ring

C

x1

Knurled Nut

E

x3

Lock Ring

G

x3

Shade

H

x1

Crossbar
x1

Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700

Hardware Contents

Nipple

DD

x1

Mounting Ball

EE

x1

Thank you for purchasing a Quoizel product.

or visit us on-line at www.quoizel.com

I

Finial
x3

STEP 1 Install Crossbar-

A. Attach the Lock Screw (D) from the top of the Ceiling Canopy (A).

Place the (E), the Rings (B/C) and the Washers
(F) over the end of the Lock Screws (D) as shown. Secure them
together with the Lock Ring (G). Tighten until snug.

STEP 2 Install Crossbar-

A. AA)Attach the Crossbar ( to the Outlet Box with the head of the

Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included) Tighten until snug..

Figure 2

STEP 3 Install Nipple to Crossbar-

* Pliers is required for this step.

A. Thread one Hex Nut (CC) to the middle of the Nipple (DD). Place the

Lock Washer (BB) over the Nipple (DD) and then thread the Nipple
(DD) into the Crossbar (AA) until the Nipple (DD) is about 0.375”
above the Crossbar (AA).

B. Position the center hole of the Ceiling Canopy (A) over the end of

the Nipple (DD).Adjust the Nipple (DD) so approx 0.375” of the
Nipple (DD) is protruding from the mounting hole on the Ceiling
Canopy (A). This adjustment may take a few tries.

C. Remove the Ceiling Canopy (A) and then tighten the Hex Nut (CC)

against the Crossbar (AA) to secure in place.

D. Thread another Hex Nut (CC) onto the end of the Nipple (DD).

1of2

Knurled Nut Rubber

A

F

F

F

Figure 1

Outlet Box

AA

Outlet Box Screw
(not included)

Green Ground Screw

D

E

B

C

G

January2014

Thread this Hex Nut (CC) on just enough so the inside surface of the
Ceiling Canopy (A) rests against it. * You may have to trial fit the
Ceiling Canopy (A) one more times to insure this distance also. This
Hex Nut (CC) is needed here to prevent you from crushing down the

center of the Ceiling Canopy (A).
E. Refer to Step 4 for wire connections.
F. Attach the Ceiling Canopy (A) over the end of the Nipple (DD) and

secure with the Mounting Ball (EE). Hand tighten until snug.

Figure 3

BB

AA

DD

CC

Step A

CC

Step D

D. Connect Ground Wire from the Outlet Box to Ground Wire from

fixture.
E. Twist connectors until wires are tightly joined together.
F. Wrap each connection with approved electrical tape and carefully

stuff all the connected wires into the Outlet Box.

STEP 5 - Install Bulb

A. This fixture uses standard bulb with medium base. Maximum 60

watts.

B. Insert bulb and screw snugly into place.

Figure 5

Bulb

A

EE

STEP 4 - Wire Connections

A. Use standard wire connectors (not included) to make all wire

connections. (Connectors are not included with fixture.) Strip and
prepare wire ends according to instructions supplied with
connectors.

B. Connect White Supply Wire from the Outlet Box to Ribbed side Wire

from fixture.

C. Connect Black (or Red) Supply Wire from the Outlet Box to Smooth

side Wire from fixture.

White wire

from supply

Black wire from
supply (or Red)

Ground wire

from supply

Ribbed side wire
from fixture

Smooth side wire
from fixture

Ground wire
from fixture

Figure 4

PCAT1617C

TWO LIGHTS SHOWN FOR ILLUSTRATION PURPOSE ONLY.

FINISH: POLISHED CHROME

STEP 6 - Install Shade

A. Attach the Shade (H) onto the Small Ring (C) and secure by

threading the Finial (I) onto the Lock Screw (D). Tighten gently until
snug.

Your fixture is now assembled and ready to use. Enjoy!

C

I

Figure 6

H

9” Dia.

D

(3) 60W

Base

(Not Supplied)

PART NUMBER

NO.

G3819MR

1

G3846MR

2

G3847SH

3

2014 QuoizelInc.

Medium

Bulbs

13.5” Dia.

16.5” Dia.

NOTE: ALL DIMENSIONS ARE ROUNDED UPTO THE NEAREST 1/2"

REPLACEMENT PART DESCRIPTION

MIRROR GLASS 15.5"D

MIRROR GLASS FLAT (BOTTOM) 16.5"D

SHADE ETCHED GLS PAINTED INSIDE 13.5"D

REQ.

1

1

1

Thank you for purchasing a Quoizel product.

Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700

or visit us on-line at www.quoizel.com

2of2

2

1

5”

3”

3

January2014