Quoizel OZ1613IN User Manual
Assembly Instruction Sheet #IS-OZ1613
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
Quoizel, Inc.
6 Corporate Parkway
Goose Creek, SC 29445
Customer Service
Phone 631.273.2700
Fax 631.231.7102
www.quoizel.com
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
,.
For Style OZ1613PN and OZ1613IN
ToolsRequired: Flatheadscrewdriver, Phillipsscrewdriver,pliers,wire cutters, wire strippers, electricaltape,
safetyglasses.
BulbRecommended: (2) MediumBase 60W Maximum,Alternatebulb (2) 13W CFL
EstimatedAssembly Time:20-30minutes
Preparation:Identify and inspect all partsbeforebeginning installation. Check package contentlist and diagrams
belowto be sure all partsarepresent. If any parts aremissing or damaged, do not attemptto assemble, install, or
operatethe fixture. Contact customer serviceforreplacement parts.
Package Contents
Ceiling
A
Canopy
x1
Finial
B
x1
Lock Ball
C
x3
Shade
D
Holder
x1
STEP 1 Install Crossbar-
A. AA)Attach the Crossbar ( to
the Outlet Box with the head of
the Green Ground Screw
facing you. Secure it with
Outlet Box Screws (not
included) Tighten until snug..
STEP 2 - Attach Nipple to Crossbar
A. Thread one Hex Nut (DD) onto the top end of the Nipple (BB).
B. Place one Lock Washer (CC) over the top end of the Nipple (BB) and
then thread the Nipple (BB) into the center lock hole of the Crossbar
(AA).
C. Using pliers, thread the Hex Nut (DD) against the Crossbar (AA) and
hand tighten until snug.
D. Thread the other Hex Nut (DD) onto the other end of the Nipple
AA
Green Ground Screw
CC
DD
Allen Bolt
E
x3
Rubber
F
Washer
x3
Flat
Washer
G
x6
Shade
H
x1
Outlet Box
AA
Outlet Box Screw
(not included)
Figure 1
Figure 2
Hardware Contents
Crossbar
AA
x1
Nipple
BB
x1
Lock Washer
CC
x1
(BB). Thread this Hex Nut (DD) on just enough so the inside
surface of the Ceiling Canopy (A) rests against it. * You may have
to trial fit the Ceiling Canopy (A) one more times to insure this
distance also. This Hex Nut (DD) is needed here to prevent you
from crushing down the center of the Ceiling Canopy (A).
STEP 3 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Strip and
prepare wire ends according to instructions supplied with
connectors.
B. Connect White Supply Wire from the Outlet Box to Ribbed side
Wire from fixture.
C. Connect Black (or Red) Supply Wire from the Outlet Box to Smooth
side Wire from fixture.
D. Connect Ground Wire from the Outlet Box to Ground Wire from
fixture.
E. Twist connectors until wires are tightly joined together.
F. Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from supply
Black wire from
supply (or Red)
Ground wire
from supply
Ribbed side wire
from fixture
Smooth side wire
from fixture
Ground wire
from fixture
Hex Nut
DD
x2
Big Flat Washer
EE
x1
Allen Wrench
FF
x1
Figure 3
2014 Quoizel Inc.
DD
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
BB
A
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
1of2
March2014
STEP 4 Attach Ceiling Canopy-
STEP 6 Attach Shade to Shade Holder-
A. Position the Ceiling Canopy (A) to the ceiling by passing the
Nipple (BB) through the center hole.
B. Slip on the Big Flat Washer (EE) and then thread the Finial (B) to
the bottom end of the Nipple (BB). Snug down assembly until the
Ceiling Canopy (A) is flush against the ceiling.
* Be sure that there are no trapped or pinched wires along the
edge of the Ceiling Canopy (A).
BB
A
EE
B
Figure 4
STEP 5 - Install Bulb
A. standard bulb
This fixture uses
with a medium screw base
Maximum 60 watts.
B. Insert bulb and screw snugly
into place.
.
Socket
Figure 5
OZ1613PN/OZ1613IN
FINISH: PALLADIAN BRONZE
/IRON GATE
A. Place and over the Allen
Flat Washers (G) the Rubber Washer (F)
Bolt (E).
B. Place the Shade (H) into the Shade Holder (D), line up the holes on
the side of the Shade (H) and the mounting holes on the Balls. Pass
The Allen Bolts (E) with washers
(F/G) through the holes on the
Shade (H), thread into the mounting
holes on the Balls by using the Allen
Wrench (FF). Please make sure
that the Allen Bolts (E) don’t
FF
D
penetrate opening of the Ball, this
will allow the support arms to pass
through the Ball to attach the Shade
(H) to the Ceiling Canopy (A).
Figure 6
STEP 7 - Install Shade
A
A. Pass the hole on the Shade
Holder (D) through the Bolts on
the side of the Ceiling Canopy
(A) and secure with the Lock
Balls (C). Hand tighten until
sung.
Your fixture is now assembled
Bulb
and ready to use. Enjoy!
8” Dia.
E
Ball
G
Figure 7
F
H
Bolt
D
C
2.4mm
(2) 60W
Base
(Not Supplied)
PART NUMBER
NO.
11613INOZ
1
8602KIT
2
G2236SH
3
13Ga
Medium
Bulbs
GND
QUOIZEL
R
1
2
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2"
REPLACEMENT PART DESCRIPTION
BASE IRON GATE FOR OZ1613IN
KIT QMH-13 REPLACEMENT
SHADE ETCHED WITH WHITE PAINTED INSIDE 12.5"D
5”
4”
3
12” Dia.
13” Dia.
REQ.
ITEM NUMBER
1
1
OZ1613IN
1
2014 Quoizel Inc.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
2of2
March2014
Loading...