Preparation:Identifyandinspect all partsbeforebeginninginstallation. Check package
contentlistanddiagrams below tobesureall parts arepresent.Ifany parts aremissing
ordamaged,donot attempt toassemble,install,or operate thefixture.Contactcustomer
serviceforreplacementparts.
Assembly Instruction Sheet #IS-NY8318B
For Style NY8318B
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing
the fixture. We strongly recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool
before removal. Do not subject glass parts to any shock while in operation or shattering may result.
Package Contents
A
Part
ACrossbar
B
C
D
E
F
G
Description
Mounting Screw
Lock Washer
Hex Nut
Mounting Ball
Fixture Body
Candle Cover
Quantity
1pc.
2 pcs.
2 pcs.
2 pcs.
2 pcs.
1pc.
3 pcs.
F
B
C
D
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
2012 Quoizel Inc.
E
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
1of6
G
March2012
NY8318B
FINISH: POLISHED BRASS
2
11”
22.5”
15.5”
1
11.5”
(3) 60W Candelabra
base bulbs
(not Supplied)
PART NUMBER
NO.
1
M2238CCBCANDLE COVER3.125"HPOLISHED BRASS
2
9450KIT
3
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2"
REPLACEMENT PART DESCRIPTION
MOUNTING HARDWARE4"D
POLISHED BRASS
2of6
REQ.
3
1
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
Assembly Instruction Sheet #IS-NY8318B
For Style NY8318B
STEP 1 - Attach Mounting Screws, Lock
Washers and Hex Nuts to Crossbar
A. Line up a set of holes on the Crossbar (A) and Holes on
the backplate of the Fixture Body (K).
B. Thread Mounting Screws (B) into the holes on the
Crossbar (A), pass Lock Washers (C) and thread Hex
Nut (D) onto the Mounting Screws (B). Hand tighten
until snug.
STEP 2 - Attach Crossbar to Outlet Box
A. Attach the Crossbar (A) to Outlet Box and secure by
threading Outlet Box Screws (not supplied) into the
Mounting Holes on the Outlet Box. Tighten until snug.
Mounting
Screw
Crossbar
Figure 1
Lock Washer
Hex Nut
Fixture
Body
Mounting Hole
Crossbar
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
2012 Quoizel Inc.
Outlet Box
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
3of6
Outlet Box
Screw
Figure 2
March2012
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
Assembly Instruction Sheet #IS-NY8318B
For Style NY8318B
STEP 3Make Wire Connections-
A. Use standard wire connectors to make all wire
connections. (Connectors are not included with fixture.)
Strip and prepare wire ends according to instructions
supplied with connectors.
B. Connect White Supply Wire from the Outlet Box to White
Wire from fixture.
C. Connect Black (or Red) Supply Wire from the Outlet Box
to Black Wire from fixture.
D. Connect Ground Wire from the Outlet Box to Ground
Wire from fixture.
E. Twist connectors until wires are tightly joined together.
F. Wrap each connection with approved electrical tape and
carefully stuff all the connected wires into the Outlet Box.
White wire from supplyWhite wire from fixture
Figure 3
Black wire from supply
(or Red)
Ground wire from supplyGround wire from fixture
Black wire from fixture
Figure 4
STEP 4 - Attach Fixture Body to Mounting
Screw
A. Place the backplate of the Fixture Body (F) over the
Mounting Screws (B) and secure with Mounting Balls
(E). Hand tighten until snug.
Mounting
Figure 5
Backplate
Screw
Mounting Ball
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
2012 Quoizel Inc.
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
4of6
March2012
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
Assembly Instruction Sheet #IS-NY8318B
For Style NY8318B
STEP 5Attach Candle Cover to Socket
-
Assembly
A. Place the Candle Cover (G) over the Socket properly.
STEP 6 - Install Bulb
A. This fixture uses standard bulb with a candelabra screw
base. Maximum 60 watts.
B. Place the bulb from the bottom of the glass frame. Insert
bulb and screw snugly into place.
Candle
Cover
Socket
Figure 6
Bulb
Socket
STEP 7Apply Silicone Sealer to Mounting
-
Balls
A. To prevent moisture from entering the wire
compartment, apply a small amount of silicone sealer
(not included) to the threaded side of the mounting
balls (E) and then install them onto the mounting
screws (B). Wipe off excess caulk.
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
2012 Quoizel Inc.
or visit us on-line at www.quoizel.com
Figure 7
Figure 8
Mounting Ball
March2012
5of6
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
Assembly Instruction Sheet #IS-NY8318B
For Style NY8318B
STEP 8Apply Silicone Sealer to Backplate-
A. Make sure exterior wall surface and fixture backplate
are free of dirt before applying caulk. Using exterior
grade caulk, start on one side of fixture backplate and
follow contour, where the fixture backplate meets the
exterior wall surface upward. Proceed to caulk over top
of backplate and down other side. Do not caulk bottom
of fixture backplate to ensure proper moisture
drainage.
Your fixture is now assembled and ready to use.
Enjoy!
Figure 9
Outdoor Fixture
Backplate
Exterior
Grade Caulk
Exterior Wall Surface
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
2012 Quoizel Inc.
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
6of6
March2012
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.