Quoizel NY8315A User Manual

Page 1

6 CORPORATE PARKWAY GOOSE CREEK SC 29445 www quoizel com

Quoizel, Inc. 6 Corporate Parkway Goose Creek, SC 29445

Customer Service Phone 631.273.2700 Fax 631.231.7102 www.quoizel.com

ToolsRequired:Flatheadscrewdriver,Phillipsscrewdriver,pliers,wire cutters, wire strippers,electricaltape,safety glasses.

BulbRecommended: (1) MediumBase150WMaximum EstimatedAssemblyTime: 20-30minutes

Preparation:Identifyandinspect all partsbeforebeginninginstallation. Check package

contentlistanddiagrams below tobesureall parts arepresent.Ifany parts aremissing ordamaged,donot attempt toassemble,install,or operate thefixture.Contactcustomer serviceforreplacementparts.

Assembly Instruction Sheet #IS-NY8315A

For Style NY8315A

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject glass parts to any shock while in operation or shattering may result.

Package Contents

Part

A Crossbar

Description

Mounting Screw

Lock Washer

Hex Nut

Mounting Ball

Fixture Body

Quantity

1pc.

2 pcs.

1pc.

Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700

2012 Quoizel Inc.

Thank you for purchasing a Quoizel product.

or visit us on-line at www.quoizel.com

1of5

March2012

Page 2

NY8315A

FINISH:

ANTIQUE BRASS

6” Dia.

7”

(1)150W medium

base bulbs

(not Supplied)

12.5”

7”

NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2"

PART NUMBER

NO.

REPLACEMENT PART DESCRIPTION

9448KIT MOUNTING HARDWARE ANTIQUE BRASS 4"D

2of5

REQ.

Page 3

6 CORPORATE PARKWAY GOOSE CREEK SC 29445 www quoizel com

Assembly Instruction Sheet #IS-NY8315A

For Style NY8315A

STEP 1 - Attach Mounting Screws, Lock

Washers and Hex Nuts to Crossbar

A. Line up a set of holes on the Crossbar (A) and Holes on

the backplate of the Fixture Body (K).

B. Thread Mounting Screws (B) into the holes on the

Crossbar (A), pass Lock Washers (C) and thread Hex Nut (D) onto the Mounting Screws (B). Hand tighten until snug.

STEP 2 - Attach Crossbar to Outlet Box

A. Attach the Crossbar (A) to Outlet Box and secure by

threading Outlet Box Screws (not supplied) into the Mounting Holes on the Outlet Box. Tighten until snug.

Mounting Screw

Crossbar

Figure 1

Lock Washer

Hex Nut

Fixture

Body

Mounting Hole

Crossbar

Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700

2012 Quoizel Inc.

Outlet Box

Thank you for purchasing a Quoizel product.

or visit us on-line at www.quoizel.com

3of5

Outlet Box

Screw

Figure 2

March2012

Page 4

6 CORPORATE PARKWAY GOOSE CREEK SC 29445 www quoizel com

Assembly Instruction Sheet #IS-NY8315A

For Style NY8315A

STEP 3 Make Wire Connections-

A. Use standard wire connectors to make all wire

connections. (Connectors are not included with fixture.) Strip and prepare wire ends according to instructions supplied with connectors.

B. Connect White Supply Wire from the Outlet Box to White

Wire from fixture.

C. Connect Black (or Red) Supply Wire from the Outlet Box

to Black Wire from fixture.

D. Connect Ground Wire from the Outlet Box to Ground

Wire from fixture. E. Twist connectors until wires are tightly joined together. F. Wrap each connection with approved electrical tape and

carefully stuff all the connected wires into the Outlet Box.

White wire from supply White wire from fixture

Figure 3

Black wire from supply

(or Red)

Ground wire from supply Ground wire from fixture

Black wire from fixture

Figure 4

STEP 4 - Attach Fixture Body to Mounting

Screw

A. Place the backplate of the Fixture Body (F) over the

Mounting Screws (B) and secure with Mounting Balls

(E). Hand tighten until snug.

Mounting

Figure 5

Backplate

Screw

Mounting Ball

Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700

2012 Quoizel Inc.

Thank you for purchasing a Quoizel product.

or visit us on-line at www.quoizel.com

4of5

March2012

Page 5

6 CORPORATE PARKWAY GOOSE CREEK SC 29445 www quoizel com

Assembly Instruction Sheet #IS-NY8315A

For Style NY8315A

STEP 5 - Install Bulb

A. standard bulb with a medium screw

This fixture uses

base 150

. Maximum watts.

B. Insert bulb and screw snugly into place.

Bulb

STEP 6 Apply Silicone Sealer to Mounting

Balls

A. To prevent moisture from entering the wire

compartment, apply a small amount of silicone sealer

(not included) to the threaded side of the mounting

balls (E) and then install them onto the mounting

screws (B). Wipe off excess caulk.

STEP 7 Apply Silicone Sealer to Backplate-

A. Make sure exterior wall surface and fixture backplate

are free of dirt before applying caulk. Using exterior

grade caulk, start on one side of fixture backplate and

follow contour, where the fixture backplate meets the

exterior wall surface upward. Proceed to caulk over top

of backplate and down other side. Do not caulk bottom

of fixture backplate to ensure proper moisture

drainage.

Mounting Ball

Socket

Outdoor Fixture Backplate

Figure 6

Figure 7

Figure 8

Exterior Grade Caulk

Your fixture is now assembled and ready to use.

Enjoy!

Thank you for purchasing a Quoizel product.

Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700

2012 Quoizel Inc.

or visit us on-line at www.quoizel.com

Exterior Wall Surface

March2012

5of5