
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
. .
, .
INSTRUCTION SHEET IS NA1716-
STYLE NUMBER NA1716BN:
PACKAGE CONTENTS
Part
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
Lock Washer (for #8-32 Screw)
Description
Crossbar
Green Ground Screw
Mounting Screw
Hex Nut (for #8-32 Screw)
Mounting Ball
Hex Nut (1/8IP)
Lock Washer (for 1/8IP)
Lock Screw
Ceiling Canopy
Wheel Part
Spacer Tube
Center Stem with Hex Nut
Side Rod
Socket Assembly
Shade
Shade Holder
Quantity
1pc
1pc
2pcs
2pcs
2pcs
2pcs
1pc
1pc
3pcs
1pc
1pc
1pc
1pc
3pcs
1pc
1pc
1pc
Revised 2008-11-11
J
A
B
C
D
E
F
G
H
I
K
L
M
N
O
P
Q
!
WARNINGS AND CAUTIONS
WARNING:
● Befo re beginning the in stal la tion, tu rn off el ectricity at th e circuit breaker box or the ma in fuse box by
switching off the circuit breaker or removing the fuse.
CAUTIONS:
● These instructions are provided for your safe ty. It is very i mportant t hat they a re read completely before
the installation of your fixture. We strongly recommend that a professional electrician install the fixture.
● Di sconnect fixture from t he power source before replacing t he bulb( s), ma king sure t he bulb(s) had
sufficient time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may
result.
PREPARATION
● Befo re beginning in st allation of prod uct, make sure a ll parts are present. Comp ar e parts with p ac kage
contents list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or
operate the product. Contact customer service for replacement part.
● Estimated Assembly Time : 30 45 minutes
● Tools R equi red for Assembly (not included): F lath ea d screwdriver Phillips screwdriver, pliers, electrical
tape, wire cutters, safety glasses &3, 100 Watt, Type A Medium Base Bulbs.
● He lp ful Tools (not included): Wire Strippers.
,
-
1 OF 3

INSTALLATION INSTRUCTIONS
STEP 1:
a Thread the Center Stem into the Hex Coupling on the top
.
center of the SocketAssembly as shown. Using plier,
thread Hex Nut against the Hex Coupling and hand tighten
until snug.
STYLE NUMBER NA1716BN:
Center Stem
with Hex Nut
Hex Coupling
Socket
Assembly
STEP 2:
a Locate the Spacer Tube, the Wheel Part and the Ceiling
.
Canopy over the top end of the Center Stem in turn.
Lock Washer
(1/8 IP)
Secure by threading Lock Washer (1/8IP) and Hex Nut
(1/8IP) onto the Center Stem. Hand tighten until snug.
Wheel Part
STEP 3:
a Install correct bulbs referring to fixture markings and or labels for maximum wattage. / .
Hex Nut (1/8IP)
Ceiling
Canopy
Spacer Tube
Center Stem
STEP 4:
a Locate the Shade inside of the Shade Holder.
.
b. Lift the Shade Holder with Shade upward, line up mounting
holes on the Wedge and holes on the Fixture Pan. Thread
Lock Screws into mounting holes on Wedges and tighten
until snug to secure the Shade.
2 OF 3
Lock
Screw
Shade Holder
Fixture Pan
Shade
Wedge

INSTALLATION INSTRUCTIONS
STEP 5:
a Locate Side Rods from the top of fixture, through the holes
.
on the side of the Ceiling Canopy and then place into the
holes on the heads of the Lock Screws (Refer to the
illustration).
STYLE NUMBER NA1716BN:
Side Rod
Ceiling
Canopy
Lock Screw
STEP 6:
a Screw the Mounting Screws into the Crossbar place the
. ,
Lock Washers over the Mounting Screws and thread the
Hex Nuts onto the Mounting Screws as shown Secure the
.
position of the Mounting Screws by tightening the Hex
Nuts against the Crossbar
b Secure the Crossbar to the Outlet Box with Outlet Box
.
Screws
.
.
STEP 7:
* ( )
Use Wire Connectors not supplied to connect the
.
wires
.
a Connect the House Ground Wire to the Fixture Ground
Wire.
. ( )
b Connect the House White or Ribbed Wire to the
Fixture Supply Wire White or Ribbed Side .
. ( )
c Connect the House Black or Red Wire to the Fixture
Supply Wire Black or Smooth Side
.
d Wrap each connection with approved electrical tape and
( ).
carefully stuff all of the connected wires into the Outlet
.
Box
( )
Mounting Screw
Outlet Box
WHITE OR RIBBED
FROM HOUSE
BLACK OR RED WIRE( )
FROM HOUSE
GROUND WIRE GROUND WIRE
FROM HOUSE FROM FIXTURE
Crossbar
Lock Washer
Outlet Box Screw
WHITE OR RIBBED
FROM FIXTURE
BLACK OR SMOOTH
FROM FIXTURE
Hex Nut
STEP 8:
.a Place Ceiling Canopy onto Outlet Box aligning 2 holes in
the Backplate with 2 Mounting screws threaded on the
Crossbar and secure it against wall with Mounting Balls
. . .Your installation is completed now Restore electricity Retain this sheet for future reference
3 OF 3
Crossbar
.
Mounting Screw
Ceiling Canopy
Mounting Ball