Quoizel NA1616BN User Manual
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
INSTRUCTION SHEET IS NA1616:STYLE NUMBER NA1616BN:
PACKAGE CONTENTS
Part
A
B
C
D
E
F
G
H
I
J
Crossbar
Green Ground Screw
Hex Nut
Lock Washer
Nipple
Knob
Lock Screw
Ceiling Canopy
Shade
Shade Holder
Description
Quantity
1pc
1pc
1pc
1pc
1pc
1pc
3pcs
1pc
1pc
1pc
Revised 2010-02-25
A
B
C
D
I
E
F
G
H
J
!
WARNINGS AND CAUTIONS
WARNING:
●
Before beginning the installation, turn off electricity at the circuit breaker box or the main fuse box by
switching off the circuit breaker or removing the fuse.
CAUTION:
●
These instructions are provided for your safety. It is very important that they are read completely before
the installation of your fixture. We strongly recommend that a professional electrician install the fixture.
●
Disconnect fixture from the power source before replacing the bulb(s), making sure the bulb(s) had
sufficient time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may
result.
PREPARATION
●
Before beginning installation of product, make sure all parts are present. Compare parts with package
contents list and diagram above. If any part is missing or damaged, do not attempt to assemble, install
or operate the product. Contact customer service for replacement part.
●
Estimated Assembly Time : 20 30 minutes
●
Tools Required for Assembly (not included) : Flathead screwdriver Phillips screwdriver, Pliers,
Electrical tape, Wire cutters, Safety glasses & 3, 60 Watt, Type - A medium base Bulbs.
●
Helpful Tools (not included) : Wire Strippers.
,
1OF3
INSTALLATION INSTRUCTIONS
STEP 1:
a Locate the Crossbar and attach it to the Outlet Box
.
using the Outlet Box Screws not supplied
b Locate the Nipple and thread one Hex Nut onto it
.
about half way. Slip a Lock Washer onto it and thread
one end of the nipple into the center hole of the
Crossbar
c Position the Ceiling Canopy over the outlet box,
.
.
passing the mounting hole in the center of the Ceiling
Canopy over the end of Nipple
d Adjust the Nipple so approx 3 8 inch of the Nipple is
.
protruding from the mounting hole. This adjustment
may take a few tries.
e When this length is achieved, remove the Ceiling
.
Canopy and tighten the Hex Nut up against the
underside of the Crossbar with pliers.
STEP 2:
*()
Use Wire Connectors not supplied to connect the
.
wires
.
a Connect the House Ground Wire to the Fixture Ground
Wire.
.()
b Connect the House White or Ribbed Wire to the
Fixture Supply Wire White or Ribbed Side .
.()
c Connect the House Black or Red Wire to the Fixture
Supply Wire Black or Smooth Side
.
d Wrap each connection with approved electrical tape and
().
carefully stuff all of the connected wires into the Outlet
.
Box
()
().
.
./"
STYLE NUMBER NA1616BN:
Outlet Box
Screw
Hex Nut
Nipple
WHITE OR RIBBED
FROM HOUSE
BLACK OR RED WIRE()
FROM HOUSE
GROUND WIRE GROUND WIRE
FROM HOUSE FROM FIXTURE
Lock Washer
Ceiling Canopy
WHITE OR RIBBED
FROM FIXTURE
BLACK OR SMOOTH
FROM FIXTURE
Outlet Box
Crossbar
STEP 3:
a Position the Ceiling Canopy to the ceiling by. passing
the Nipple through the center hole. Secure the Ceiling
Canopy by threading the Knob onto the Nipple. Hand-tighten
until snug.
Nipple
Ceiling Canopy
Knob
STEP 4 :
a Install correct bulbs referring to fixture markings and or labels for maximum wattage./.
2OF3
Loading...