Preparation:Identifyandinspect all partsbeforebeginninginstallation. Check package
contentlistanddiagrams below tobesureall parts arepresent.Ifany parts aremissing
ordamaged,donot attempt toassemble,install,or operate thefixture.Contactcustomer
serviceforreplacementparts.
Assembly Instruction Sheet #IS-NA1514BN
For Style NA1514BN
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing
the fixture. We strongly recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool
before removal. Do not subject glass parts to any shock while in operation or shattering may result.
A
Package Contents
I
Part
ACrossbar
B
C
D
E
F
G
H
I
J
K
L
Description
Mounting Screw
Lock Washer
Hex Nut
Mounting Ball
Ceiling Canopy
6” Rod
12” Rod
Socket Assembly
Lock Ball
Inner Shade
Outside Shade
Quantity
1pc.
2 pcs.
2 pcs.
2 pcs.
2 pcs.
1pc.
2 pcs.
2 pcs.
1pc.
4 pcs.
1pc.
1pc.
B
J
C
D
E
F
K
L
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
2014 Quoizel Inc.
G
H
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
1of6
July2014
Page 2
NA1514BN
FINISH: BRUSHED NICKEL
6”
3
12”
2
2.4mm
13Ga
QUOIZEL
R
5” Dia.
GND
1”
1
48”
OVERALL HEIGHT INCLUDES
(2) 6” AND 12” RODS
(1)100W
Medium Base Bulb
(Not Supplied)
PART NUMBER
NO.
1
11514BNNA
2
3
4
9012EXBN
9006EXBN
G3411SH
4
4.5” Dia.
14” Dia.
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2"
REPLACEMENT PART DESCRIPTION
BASE BRUSHED NICKEL
ROD EXTENSION BRUSHED NICKEL 12"L X 0.5"D
ROD EXTENSION BRUSHED NICKEL 6"L X 0.5"D
SHADE FROSTED GLASS
2of6
9”
6”
2.5”
REQ.
1
2
2
1
Page 3
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
Assembly Instruction Sheet #IS-NA1514BN
For Style NA1514BN
STEP 1Assemble Rods-
A. Determine the Rods (G/H) to be assembled to the Socket
Assembly (I) according to your hanging height.
B. Pass Supply Wires and Ground Wire through the chosen
Rods (G/H) and then thread the chosen Rods (G/H) and
the Socket Assembly (I) together. Hand tighten until snug.
STEP 2Assemble Ceiling Canopy to Upper
-
Rod
A. Pass Supply Wires and Ground Wire through the Ceiling
Canopy (F) and then thread the Ceiling Canopy (F) and
the Upper Rod together. Hand tighten until snug.
Figure 1
Assembly
6” Rod
12” Rod
Socket
6” Rod with
Fixture Loop
12” Rod with
Nipple
Supply Wire and
Ground Wire
Figure 2
Ceiling
Canopy
Supply Wire and
Ground Wire
STEP 3 - Attach Mounting Screws, Lock
Washers and Hex Nuts to Crossbar
A. Line up a set of holes on the Crossbar (A) and Holes on
the Ceiling Canopy (F).
B. Thread Mounting Screws (B) into the holes on the
Crossbar (A), pass Lock Washers (C) and thread Hex Nut
(D) onto the Mounting Screws (B). Hand tighten until
snug.
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
2014 Quoizel Inc.
or visit us on-line at www.quoizel.com
3of6
Mounting Screw
Lock Washer
Ceiling
Canopy
Upper Rod
Crossbar
Hex Nut
Figure 3
July2014
Page 4
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
Assembly Instruction Sheet #IS-NA1514BN
For Style NA1514BN
STEP 4 - Attach Crossbar to Outlet Box
A. Attach the Crossbar (A) to Outlet Box and secure by
threading Outlet Box Screws (not supplied) into the
Mounting Holes on the Outlet Box. Tighten until snug.
STEP 5Make Wire Connections-
A. Use standard wire connectors to make all wire
connections. (Connectors are not included with fixture.)
Strip and prepare wire ends according to instructions
supplied with connectors.
B. Connect White Supply Wire from the Outlet Box to White
Wire from fixture.
C. Connect Black (or Red) Supply Wire from the Outlet Box
to Black Wire from fixture.
D. Connect Ground Wire from the Outlet Box to Ground
Wire from fixture.
E. Twist connectors until wires are tightly joined together.
F. Wrap each connection with approved electrical tape and
carefully stuff all the connected wires into the Outlet Box.
Figure 4
Outlet
Box
Crossbar
Mounting
Hole
Outlet Box
Screw
Figure 5
White wire from supplyWhite wire from fixture
Black wire from supply
(or Red)
Ground wire from supplyGround wire from fixture
Black wire from fixture
Figure 6
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
2014 Quoizel Inc.
or visit us on-line at www.quoizel.com
4of6
July2014
Page 5
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
Assembly Instruction Sheet #IS-NA1514BN
For Style NA1514BN
STEP 6 - Attach Ceiling Canopy to Mounting
Screw
A. Place the Ceiling Canopy (F) over the Mounting Screws
(B) and secure with Mounting Balls (E). Hand tighten
until snug.
STEP 7 - Install Bulb
A. This fixture uses standard bulb with a standard screw
base. Maximum 100 watts.
B. Insert bulb and screw properly into place.
Figure 7
Mounting
Screw
Ceiling Canopy
Mounting
Ball
Bulb
Socket
Figure 8
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
2014 Quoizel Inc.
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
5of6
July2014
Page 6
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
Assembly Instruction Sheet #IS-NA1514BN
For Style NA1514BN
STEP 8 - Attach Shades to fixture
A. Place Inner Shade (K) into Outside Shade (L).
B. Pass the Hole on the Outside Shade (L) through Side
Rod. Secure by thread Lock Ball (J) onto Side Rod,
hand tighten until snug.
Your fixture is now assembled and ready to use.
Enjoy!
Figure 9
Side Rod
Inner Shade
Hole
Outside Shade
Lock Ball
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
2014 Quoizel Inc.
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
6of6
July2014
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.