Quoizel MY5103ML User Manual
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
CROSSBAR
LOCK WASHER A
LOCK NUT A
LOCK NUT B
LOCK WASHER B
FIXTURE CHAIN
,.
OUTLET BOX
HOUSE SUPPLY and
GROUND WIRES
OUTLET BOX SCREWS
not supplied()
NIPPLE
CANOPY CHAIN LOOP
FIXTURE SUPPLY
and GROUND WIRE
ASSEMBLY / INSTALLATION INSTRUCTIONS
1 Before beginning the installation carefully unpack and
.
identify all parts referring to the illustration
2 Turn power to the installation point OFF at circuit breaker
..
3 Unfold the SUPPORTARMS to the properlocations.
.
,.
Locate the SCROLL PART onto thetop end of the
JUNCTION BOX and makethe hole on the bottom of it
over the nipple onthe top center of the JUNCTION BOX.
Thread the FIXTURE LOOPonto the nipple andhand
tighten until snug tosecure them.
4. Fasten the CROSSBAR tothe OUTLET BOX with
(2)OUTLET BOX SCREWS(not supplied). Proceed to
thread LOCK NUT A and LOCK WASHER A onto
the top end ofNIPPLE. Thread NIPPLE into the center of
CROSSBAR. Locate the LOCK NUT B ontothe bottom end
of the NIPPLE. Tighten LOCK NUTA against CROSSBAR
with plier until snug.
,
FIXTURE LOOP
JUNCTION BOX
CEILING CANOPY
CANOPY LOCK RING
FIXTURE SUPPLY
and GROUND WIRE
SCROLL PART
SUPPORTARM
5. Locate the FIXTURECHAIN and determine desired
hanging height of fixture.Adjust chain by removing links if
needed. Please note thatdepending on chain material
thickness, you might berequired to use chain pliers to
spread links open. Proceedto attach one end of chain to
FIXTURE LOOP, attached to topof fixture. Pass the
fixture wires through FIXTURECHAIN alternating links.
Proceed to pass thefixture wires through the following
mounting components in thisorder: 1)CANOPY LOCK
RING; 2)CEILING CANOPY 3 CANOPY CHAIN LOOP
4 LOCK WASHER B and LOCK NUT B 5 NIPPLE
););
6 LOCK NUT A and LOCKWASHER A
).
6.
Making the connections:
;) ;
(2 people recommended forthe remaining steps) Position
the fixture under theceiling mounted outlet box. Pass
LOCK WASHER B over theNIPPLE.Thread CANOPY
CHAIN LOOP onto NIPPLE. Thread LOCK NUTB down
the NIPPLE, againstthe CANOPY CHAIN LOOP and snug
with pliers. Pass the wires through the NIPPLE. Take up
wire slack andtrim wires so thatapprox. 6” will remain
inside outlet box. Proceed to attach thetop of the FIXTURE
CHAIN to the bottomof the CANOPYCHAIN LOOP.
Using wire connectors (not supplied) connect the
HOUSE GROUND WIRE to theFIXTURE GROUND
WIRE connect the HOUSE WHITE WIRE to the
;
FIXTURE SUPPLY WIRE (WHITE or RIBBED SIDE);
connect the HOUSE BLACK(or RED) WIRE to the
FIXTURE SUPPLY WIRE(BLACK or SMOOTH SIDE).
Wrap each connection with approved electrical tape.
SOCKET
SHADE
STEEL COLLAR
SOCKET COLLAR
IF IN DOUBT ABOUT ELECTRICAL INSTALLATION,
CONSULT A LICENSED ELECTRICIAN!
7. With the properconnections made, proceed to push the
CEILING CANOPY upward over the OUTLET BOX. Be
sure that all wiresare carefully tucked into the OUTLET
BOX cavity. Secure canopy against ceiling by threading
CANOPY LOCK RING onto the CANOPY LOOP.Tighten
until snug.
8. Position the SHADEand the STEEL COLLAR overthe
SOCKET as shown. Secure them by threading the
SOCKET COLLAR onto the SOCKET.Hand tighten
until snug.
9.Install the correct bulbsreferring to fixture marking and/or
labels for maximum wattage.
10 Restore power to theinstallation point ON. Retain this
.
sheet for future reference.
REVISED 2011-07-22
IS-MY5103
Loading...