Quoizel MY1723ML User Manual
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
INSTRUCTION SHEET IS MY1723:STYLE NUMBER MY1723ML:
PACKAGE CONTENTS
Part
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
Crossbar
Green Ground Screw
Mounting Screws
Lock Washer (#8-32 UNC)
Hex Nut (#8-32 UNC)
Mounting Ball
Lock Ball
Hex Nut
Plastic Washer
Flat Washer
Check Ring
Lock Washer (1/8IP)
Shade
Ceiling Canopy Assembly
Shade Stop
Side Arm
Stem with Hex Nut
Spacer Tube
Cap
Finial
Socket Assembly
Description
Quantity
1pc
1pc
2pcs
2pcs
2pcs
2pcs
4pcs
1pc
1pc
1pc
1pc
4pcs
1pc
1pc
1pc
4pcs
1pc
1pc
1pc
1pc
1pc
ISSUED 09-2009 Revised 2010-01-19
A
N
B
C
O
D
E
F
G
H
I
J
S
T
P
Q
R
!
WARNINGS AND CAUTIONS
WARNING:
●
Before beginning the installation, turn off electricity at the circuit breaker box or the main fuse box by
switching off the circuit breaker or removing the fuse.
CAUTION:
●
These instructions are provided for your safety. It is very important that they are read completely before
the installation of your fixture. We strongly recommend that a professional electrician install the fixture.
●
Disconnect fixture from the power source before replacing the bulb(s), making sure the bulb(s) had
sufficient time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may
result.
PREPARATION
K
L
M
U
Before beginning installation of product, make sure all parts are present. Compare parts with package
●
contents list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or
operate the product. Contact customer service for replacement part.
●
Estimated Assembly Time : 20 30 minutes
●
Tools Required for Assembly (not included) : Flathead Screwdriver Phillips Screwdriver, Pliers,
,
Electrical Tape, Wire Cutters, Safety Glasses &5, 100 Watt, Type - A Medium Base Bulbs.
●
Helpful Tools (not included) : Wire Strippers.
1OF4
INSTALLATION INSTRUCTIONS
STYLE NUMBER MY1723ML:
STEP 1:
Lock Ball
a. Thread the end of the Ceiling Canopy Assembly into the
Coupling on the top center of the Socket Assembly as
shown. Line up holes on the side of the Ceiling Canopy and
Bracket on the Socket Assembly before tighten them.
Lock Washer (1/8IP)
Bolt
b. Pass Bolts on Side Arms through the holes on the side of
the Ceiling Canopy. Place another ends of Side Arms over
Studs on the Bracket.
c. Place Lock Washers (1/8IP) over Bolts on Side Arms and
thread Lock Balls onto Bolts. Hand tighten until snug to
secure Side Arms.
STEP 2:
a Screw the Mounting Screws into the Crossbar place the
.,
Ceiling Canopy
Assembly
Stud
Coupling
Bracket
Socket Assembly
Mounting Screw
Lock Washers (#8-32 UNC) over the Mounting Screws and
thread the Hex Nuts (#8-32 UNC) onto the Mounting
Screws as shown Secure the position of the Mounting
.
Screws by tightening the Hex Nuts (#8-32 UNC) against
the Crossbar
b Secure the Crossbar to the Outlet Box with Outlet Box
.
Screws
.
.
Outlet Box
Crossbar
Outlet Box Screw
Side Arm
Hex Nut
(#8-32 UNC)
Lock Washer
(#8-32 UNC)
STEP 3:
a Locate the Ceiling Canopy onto the Crossbar and slip the
.
Button Stop on the end of Lanyard into the Slot on the
Crossbar as shown.
Crossbar
Ceiling
Canopy
Slot
Button Stop
Lanyard
2OF4
Loading...