Page 1
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
Quoizel, Inc.
6 Corporate Parkway
Goose Creek, SC
29445
Customer Service
Phone 631.273.2700
Fax 631.231.7102
www.quoizel.com
,.
Assembly Instruction Sheet #IS-MC1691CIB
For Style MC1691CIB
ToolsRequired:Flatheadscrewdriver,Phillipsscrewdriver,pliers,wire cutters, wire
strippers,electricaltape,safety glasses.
BulbRecommended: (4) MediumBase60WMaximum
EstimatedAssemblyTime: 30-45minutes
Preparation:Identifyandinspect all partsbeforebeginninginstallation. Check package
contentlistanddiagrams below tobesureall parts arepresent.Ifany parts aremissing
ordamaged,donot attempt toassemble,install,or operate thefixture.Contactcustomer
serviceforreplacementparts.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing
the fixture. We strongly recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool
before removal. Do not subject glass parts to any shock while in operation or shattering may result.
Package Contents
J
Part
A Crossbar
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Description
Mounting Screw
Lock Washer
Hex Nut
Mounting Ball
Ceiling Canopy
6” Rod
12” Rod
Socket Assembly
Stem 4”L
Rubber Washer
Big Flat Washer
Hex Nut (1/8 IP)
Finial
Shade
Diffuser
Quantity
1pc.
2 pcs.
2 pcs.
2 pcs.
5 pcs.
1pc.
2 pcs.
2 pcs.
1pc.
1pc.
1pc.
1pc.
1pc.
1pc.
1pc.
1pc.
A
B
C
D
E
F
G
I
K
L
M
N
O
P
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
2013 Quoizel Inc.
H
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
1of6
October2013
Page 2
MC1691CIB
FINISH: IMPERIAL BRONZE
3
6”
2
12”
6” Dia.
1”
2.4mm
13Ga
QUOIZEL
GND
R
61”
OVERALL HEIGHT INCLUDES
(2) 6” AND 12” RODS
(4)60W Medium
Base Bulbs
(Not Supplied)
PART NUMBER
NO.
1
2
3
G149DI
9012EXIB
9006EXIB
4
20” Dia.
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2"
REPLACEMENT PART DESCRIPTION
DIFFUSER FROSTED GLASS 19.5"D
ROD IMPERAIL BRONZE 12"L X 0.5"DEXTENSION
ROD EXTENSION IMPERIAL BRONZE 6”L X 0.5"D
22.5”
8”
1
REQ.
1
2
2
4
S1555MC
SHADE MICA 20"D 1
2of6
Page 3
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
Assembly Instruction Sheet #IS-MC1691CIB
For Style MC1691CIB
STEP 1 Attach the Socket Assembly to Shade-
A. Pass the hole on the tab in the Shade (O) through the Bolt
on the Side Arm, secure by threading the Mounting Balls
(E) onto the Bolts on the Side Arm. Hand tighten until
sung.
STEP 2 Assemble Rods-
A. Determine the Rods (G/H) to be assembled to the Socket
Assembly (I) according to your hanging height.
B. Pass Supply Wires and Ground Wire through the chosen
Rods (G/H) and then thread the chosen Rods (G/H) and
the Socket Assembly (I) together. Hand tighten until snug.
Figure 1
Side Arm
Mounting Ball
Shade
Bolt
12” Rod
12” Rod
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
2013 Quoizel Inc.
6” Rod
Socket
Assembly
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
3of6
6” Rod
Supply Wire and
Ground Wire
Figure 2
October2013
Page 4
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
Assembly Instruction Sheet #IS-MC1691CIB
For Style MC1691CIB
STEP 3 Assemble Ceiling Canopy to Upper
-
Rod
A. Pass Supply Wires and Ground Wire through the Ceiling
Canopy (F) and then thread the Ceiling Canopy (F) and
the Upper Rod together. Hand tighten until snug.
STEP 4 - Attach Mounting Screws, Lock
Washers and Hex Nuts to Crossbar
A. Line up a set of holes on the Crossbar (A) and Holes on
the Ceiling Canopy (F).
B. Thread Mounting Screws (B) into the holes on the
Crossbar (A), pass Lock Washers (C) and thread Hex Nut
(D) onto the Mounting Screws (B). Hand tighten until
snug.
Mounting Screw
Lock Washer
Ceiling
Canopy
Figure 3
Ceiling
Canopy
Supply Wire and
Ground Wire
Upper Rod
Crossbar
Hex Nut
STEP 5 - Attach Crossbar to Outlet Box
A. Attach the Crossbar (A) to Outlet Box and secure by
threading Outlet Box Screws (not supplied) into the
Mounting Holes on the Outlet Box. Tighten until snug.
Figure 5
Mounting
Figure 4
Outlet
Box
Crossbar
Hole
Outlet Box
Screw
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
2013 Quoizel Inc.
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
4of6
October2013
Page 5
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
Assembly Instruction Sheet #IS-MC1691CIB
For Style MC1691CIB
STEP 6 Make Wire Connections-
A. Use standard wire connectors to make all wire
connections. (Connectors are not included with fixture.)
Strip and prepare wire ends according to instructions
supplied with connectors.
B. Connect White Supply Wire from the Outlet Box to White
Wire from fixture.
C. Connect Black (or Red) Supply Wire from the Outlet Box
to Black Wire from fixture.
D. Connect Ground Wire from the Outlet Box to Ground
Wire from fixture.
E. Twist connectors until wires are tightly joined together.
F. Wrap each connection with approved electrical tape and
carefully stuff all the connected wires into the Outlet Box.
White wire from supply White wire from fixture
Black wire from supply
(or Red)
Ground wire from supply Ground wire from fixture
Black wire from fixture
Figure 7
STEP 7 - Attach Ceiling Canopy to Mounting
Screw
A. Place the Ceiling Canopy (F) over the Mounting Screws
(B) and secure with Mounting Balls (E). Hand tighten
until snug.
Figure 6
Figure 8
Mounting
Screw
Ceiling Canopy
Mounting
Ball
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
2013 Quoizel Inc.
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
5of6
October2013
Page 6
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
Assembly Instruction Sheet #IS-MC1691CIB
For Style MC1691CIB
STEP 8 Install Diffuser-
A. Screw the beaded end of the Stem (J) into the Coupling
underside of the Socket Assembly (I). Hand tighten until
snug.
B. Pass the Diffuser (P), the Rubber Washer (K) and the
Flat Washer (L) over the othre end of the Stem (J).
Thread the Hex Nut (1/8 IP) (M) onto the Stem (J) to
secure the Diffuser (P). Tighten gently until snug.
C. Thread the Finial (N) onto the end of the Stem (J) and
hand tighten until snug.
STEP 9 - Install Bulb
A. This fixture uses standard bulb with medium screw
base. Maximum 60 watts.
B. Insert bulb and screw snugly into place.
Your fixture is now assembled and ready to use.
Enjoy!
Flat Washer
Finial
Figure 9
Shade
Tab
Coupling
Stem
Diffuser
Rubber Washer
Hex Nut (1/8 IP)
Socket
Bulb
Figure 10
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
2013 Quoizel Inc. October2013
or visit us on-line at www.quoizel.com
6of6
Loading...