Quoizel MBH8407PN User Manual
Assembly Instruction Sheet #IS-MBH8407PN
For Style MBH8407PN
Quoizel, Inc.
6 Corporate Parkway
Goose Creek, SC 29445
Customer Service
Phone 631.273.2700
Fax 631.231.7102
www.quoizel.com
ToolsRequired: Flatheadscrewdriver, Phillipsscrewdriver,pliers,wire cutters, wire strippers, electricaltape,
safetyglasses.
BulbRecommended: (1) MediumBase 100W Maximum,Alternatebulb (1) 23W CFL
EstimatedAssembly Time:
Preparation:
belowto be sure all partsarepresent. If any parts aremissing or damaged, do not attemptto assemble, install, or
operatethe fixture. Contact customer serviceforreplacement parts.
Fixturecan only be mounted inthedirection indicated on page 2.
Identifyand inspect all parts beforebeginninginstallation. Check package content listand diagrams
30-45minutes
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Package Contents
Fixture Body
A
x1
Crossbar Assembly
B
x1
STEP 2 Install Inner Backplate-
A. Pass the supply wires through the Crossbar Assembly (AA). Attach
the Crossbar Assembly (AA) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included). Tighten until snug.
Supply Wires with
Outlet Box
Figure 2
Ground Wire
B
Outlet Box Screws
(not included)
STEP 1 Install Shade-
Unscrew the Lock Screw, remove the Cage, the Glass Shade and
A.
the Tab from the Fixture Body ( ).
inside of the shade.
B. Place Glass Shade into the Cage, secure by place the Tab into the
Cage press on the Glass Shade.
C. Set the Cage with Glass Shade into the Cap on the Fixture Body,
secure by threading the Lock Screw into the Cap, tighten until sung.
A Remove the Styrofoam from
Fixture Body
Tab
Glass Shade
Lock Screw
Cage
Figure 1
STEP 3 Fit Fixture Body to
A. Remove mounting balls from the
STEP 4 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
B. Connect White Supply Wire from the Outlet Box to Ribbed side Wire
C. Connect Black (or Red) Supply Wire from the Outlet Box to Smooth
D. Connect Ground Wire from the Outlet Box to Ground Wire from
-
Crossbar Assembly
Crossbar Assembly (B). Fit the
Fixture Body (A) Crossbar
Assembly (B) and secure with
mounting balls. Note: The
backplate of the Fixture Body (A)
should be snug against the wall
surface and the mounting balls. If
not, adjust the length of the nipple
on the CrossbarAssembly (B) by
unscrewing the preassembled hex
nut and lock washer and then
screwing the mounting screws in or
out of the crossbar until the correct
length is achieved. Once the
backplate of the Fixture Body (A) is
secure, remove the mounting ball
and Fixture Body (A) and proceed
to Step 4.
connections. (Connectors are not included with fixture.) Strip and
prepare wire ends according to instructions supplied with
connectors.
from fixture.
side Wire from fixture.
Mounting
Ball
A
Hex Nut and
Lock Washer
Mounting
Screw
Figure 3
B
2014 QuoizelInc.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
1of2
February2014
fixture.
E. Twist connectors until wires are tightly joined together.
F. Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from supply
Black wire from
supply (or Red)
Ground wire
from supply
STEP 5 Install Fixture Body-
A. Carefully tuck all wires into the outlet
box and position the backplate of
fixture body (A) over the outlet box.
Align the holes in the backplate with
the mounting screws. Place caulk (not
supplied) into the previously removed
mounting balls and then attach fixture
body (A) using the mounting balls.
Hand tighten until snug.
MBH8407PN
Figure 4
Figure 5
Ribbed side wire
from fixture
Smooth side wire
from fixture
Ground wire
from fixture
Mounting
Ball
A
Mounting
Screw
STEP 6 - Install Bulb
A. This fixture uses standard bulb with medium
base . Maximum 100 watts.
B. Insert bulb and screw snugly into place.
STEP 7 - Apply Silicone Sealer
A. Make sure exterior wall surface
and fixture backplate are free of
dirt before applying caulk. Using
exterior grade caulk, caulk over
top of backplate and down other
side. Do not caulk bottom of
fixture backplate to ensure proper
B
moisture drainage.
Your fixture is now assembled and
ready to use. Enjoy!
Socket
Figure 6
Bulb
Exterior
Grade
Caulk
Backplate
Figure 7
FINISH: PALLADIAN BRONZE
Fixture can only be
mounted in the
direction indicated
8” 7” Dia.
6.5”
11”
1
4.5”
(1) 100W
Base
(Not Supplied)
PART NUMBER
NO.
G3840SH
1
2014 QuoizelInc.
Medium
Bulbs
NOTE: ALL DIMENSIONS ARE ROUNDED UPTO THE NEAREST 1/2"
REPLACEMENT PART DESCRIPTION
GLASS CLEAR SEEDY
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2of2
REQ.
1
February2014
Loading...