Quoizel LRM5006WT User Manual

Assembly Instruction Sheet #IS-LRM5006WT

6 CORPORATE PARKWAY GOOSE CREEK SC 29445 www quoizel com

Quoizel, Inc. 6 Corporate Parkway Goose Creek, SC 29445

Customer Service Phone 631.273.2700 Fax 631.231.7102 www.quoizel.com

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject glass parts to any shock while in operation or shattering may result.

Do not touch the bulb with bare hands use a cloth or glove.

For Style LRM5006WT

ToolsRequired: Flatheadscrewdriver, Phillipsscrewdriver,pliers,wire cutters, wire strippers, electricaltape,

safetyglasses.

BulbRecommended: EstimatedAssembly Time: Preparation:

belowto be sure all partsarepresent. If any parts aremissing or damaged, do not attemptto assemble, install, or operatethe fixture. Contact customer serviceforreplacement parts.

Identifyand inspect all parts beforebeginninginstallation. Check package content listand diagrams

(6)Candelabra Base 60W Maximum, Alternate bulb (6) 13WCFL

30-45minutes

Package Contents

Fixture Loop

Rot

Candle Cover

Lock Ball

Finial

STEP 1 Adjust Fixture Assembly-

A. Unfold support arms on fixture

assembly to proper locations.

STEP 2 Install Fixture Body

A. Thread the Fixture Loop A , the

B. Pass Lock Ball (D) through

and Fixture Loop together

() (F)

Rod B and the Fixture Body together as shown. Hand tighten until snug. Fixture Body (F), hand tighten until sung.

support arm, secure by threading Lock Ball (D) into Fixture Body (F), hand tighten until sung.

Thread Finial (E) onto

()

Figure 2

Fixture Body

Figure 1

QUOIZEL

Crossbar

Lock Washer

Hex Nut

Nipple

Canopy

Chain Loop x1

STEP 3 Install Crossbar-

A. Attach the Crossbar (AA) to

the Outlet Box with the head of the Green Ground Screw facing you. Secure it with Outlet Box Screws (not included) Tighten until snug

STEP 4 Install Canopy Chain Loop and Nipple-

* Pliers is required for this step.

A. Thread one Hex Nut (CC) to one end of the Nipple (DD) until it is at

least 0.25” from the end. Pass one Lock Washer (BB) over the end of the Nipple (DD) and thread the Canopy Chain Loop (EE) onto the Nipple (DD). By using pliers, thread the Hex Nut (CC) against the

Canopy Chain Loop (EE) and hand

tighten until snug.

B. Thread another Hex Nut (CC) to the

middle of the Nipple (DD). Place another Lock Washer (BB) over the Nipple (DD) and then thread the Nipple (DD) into the Crossbar (AA) until the Nipple (DD) is about 0.375” above the Crossbar (AA).

C. Remove the Canopy Lock Ring (FF) from

the Canopy Chain Loop (EE). Place the Ceiling Canopy (II) over the Canopy Chain Loop (EE) against the ceiling to determine the correct position of the Nipple (DD). Thread the Canopy Lock Ring onto the Canopy Chain Loop (EE).

Figure 3

Hardware Contents

Canopy Lock Ring

Fixture Chain

Quick Link

Ceiling Canopy

Outlet Box

Outlet Box Screw (not

Green Ground Screw

Figure 4

included)

Step B

Step A

2014 Quoizel Inc.

Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700

Thank you for purchasing a Quoizel product.

or visit us on-line at www.quoizel.com

1of3

May2014

Adjust the Nipple (DD) to allow the Ceiling Canopy (II) to rest against the ceiling when held in place by the Canopy Lock Ring (FF).

D. Remove the Canopy Lock Ring (FF) and the Ceiling Canopy (II).

Tighten the Hex Nut (CC) against the Crossbar (AA) to secure in place.

STEP 5 - Install Fixture Chain and Ceiling Canopy

A. Adjust the Fixture Chain (GG) to your desired length by removing

the links if needed.

Pliers is required for this step.

B. With the Fixture Chain (GG) not attached to the Fixture Loop (A) and

the Canopy Chain Loop (EE), pull the supply wires through the Fixture Chain (GG) alternating links.After the wires are through the Fixture Chain (GG), pull the Supply Wires and the Ground Wire through the Canopy Lock Ring (FF) and the Ceiling Canopy (II) in order.

C. Attach one end of the Fixture Chain (GG) to the Fixture Loop (A) with

one Quick Link (HH). Lift the fixture and Fixture Chain (GG) up And Attach the other end of the Fixture Chain (GG) onto the Canopy Chain Loop (EE) with another Quick Link (HH). The fixture will now hang safely. Close the chain loop at the Ceiling Canopy Loop (EE).

D. Feed the Supply Wires and Ground Wire through the Canopy Chain

Loop (EE) and Nipple (DD) into the Outlet Box. Cut the wires leaving

approximately 8” of wire extending from the Outlet Box. E. Refer to Step 5 for wire connections. F. Raise the Ceiling Canopy (II) and Canopy Lock Ring (FF) up the

Fixture Chain (GG) and over the Canopy Chain Loop (EE). Tighten

the Canopy Lock Ring (FF) onto the Canopy Chain Loop (EE) until

tight.

Suggested chain length for Ceiling height :

8’ ceiling : use 1 links of chain and 2 quick links

9’ ceiling : use 10 links of chain and 2 quick links

10’ ceiling : use 19 links of chain and 2 quick links

STEP 6 - Wire Connections

A. Use standard wire connectors (not included) to make all wire

connections. (Connectors are not included with fixture.) Strip and prepare wire ends according to instructions supplied with connectors.

B. Connect White Supply Wire from the Outlet Box to Ribbed side Wire

from fixture.

C. Connect Black (or Red) Supply Wire from the Outlet Box to Smooth

side Wire from fixture.

D. Connect Ground Wire from the Outlet Box to Ground Wire from

fixture. E. Twist connectors until wires are tightly joined together. F. Wrap each connection with approved electrical tape and carefully

stuff all the connected wires into the Outlet Box.

White wire

from supply

Black wire from supply (or Red)

Ground wire

from supply

Ribbed side wire from fixture

Smooth side wire from fixture

Ground wire from fixture

Figure 6

STEP 7 Install Candle and Bulbs-

A. place Candle Cover (C) over the Socket. B. This fixture uses candelabra bulb with standard screw base.

Maximum 60 watts.

C. Insert bulb and screw snugly into place.

Your fixture is now assembled and ready to use. Enjoy!

Supply Wires

and Ground Wire

Bulb

Socket

Figure 7

Figure 5

Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700

Thank you for purchasing a Quoizel product.

or visit us on-line at www.quoizel.com

2of3

May2014

+ 1 hidden pages