Page 1
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
INSTRUCTION SHEET IS LR5005STYLE NUMBER LR5005RZ:
PACKAGE CONTENTS
Part
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
Crossbar
Green Ground Screw
Hex Nut
Nipple
Lock Washer
Canopy Chain Loop
Canopy Lock Ring
Fixture Chain
Ceiling Canopy
Cap
Short Tube with Fixture Body
Finial
Candle Cover
Lock Screw
Fixture Loop
Side Arm
Long Tube with Fixture Body
Socket Assembly
Description
Quantity
1pc
1pc
2pcs
1pc
2pcs
1pc
1pc
1pc
1pc
1pc
1pc
1pc
5pcs
10pcs
1pc
5pcs
1pc
1pc
ISSUED 03-2010
A
B
C
D
E
F
O
G
H
I
Q
J
K
P
M
N
!
WARNINGS AND CAUTIONS
WARNING:
● Before beginning the installation, turn off electricity at the circuit breaker box or the main fuse box by
switching off the circuit breaker or removing the fuse.
CAUTIONS:
● These instructions are provided for your safety. It is very important that they are read completely before
the installation of your fixture. We strongly recommend that a professional electrician install the fixture.
● Disconnect fixture from the power source before replacing the bulb(s), making sure the bulb(s) had
sufficient time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may
result.
PREPARATION
● Before beginning installation of product, make sure all parts are present. Compare parts with package
contents list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or
operate the product. Contact customer service for replacement part.
● Estimated Assembly Time: 30 45 minutes
● Tools Required for Assembly (not included): Flathead screwdriver Phillips screwdriver, Pliers,
Electrical tape, Wire cutters, Safety glasses & (5) 60W B10 candelabra base bulbs.
● Helpful Tools (not included): Wire strippers.
R
L
,
1OF5
Page 2
INSTALLATION INSTRUCTIONS
STEP 1:
.
a Thread the end of the Long Tub with Fixture Body onto the
nipple on the top center of the Junction Box. Please make
sure the Mounting Holes on the side of the Fixture Body
line up right in the middle of two Sockets before handtighten until snug.
STYLE NUMBER LR5005RZ:
Mounting Hole
Long Tube with
Fixture Body
Socket
Socket Assembly
Junction Box
STEP 2:
a Thread the Fixture Loop onto the nipple on the top center of
.
the Long Tube with Fixture Body. Hand-tighten until snug.
STEP 3:
a Place the Cap onto the bottom of the Junction Box. Secure
.
it by threading the Short Tube with Fixture Body into the
Hex Coupling on the bottom center of the Junction Box.
Please line up the Mounting holes on the Short Tube with
Fixture Body and Long Tube with Fixture Body before
hand-tighten until snug.
Fixture Loop
Long Tube with
Fixture Body
Mounting Hole
Long Tube with
Fixture Body
2OF5
Cap
Junction Box
Hex Coupling
Short Tube with
Fixture Body
Mounting Hole
Page 3
INSTALLATION INSTRUCTIONS
STEP 4:
a Thread the Finial onto the nipple on the end of the Short
.
Tube with Fixture Body. Hand-tighten until snug.
STEP 5:
a Locate the Side Arm. Attach the holes on it onto the
.
Mounting Holes on the Long Tube with Fixture Body and
Short Tube with Fixture Body. Secure by threading Lock
Screws into the Mounting Holes. Hand-tighten until snug.
Lock Screw
STYLE NUMBER LR5005RZ:
Short Tube with
Fixture Body
Finial
Mounting
Hole
STEP 6:
a Secure the Crossbar onto the Outlet Box with Outlet Box
.
Screws Tighten until snug
..
Side Arm
Lock Screw
Long Tube
with
Fixture Body
Short Tube
with
Fixture Body
Mounting
Hole
Outlet Box
3OF5
Crossbar
Outlet Box
Screw
Page 4
INSTALLATION INSTRUCTIONS
STEP 7:
*.
Pliers is required on this step
..
a Thread one Hex Nut onto top end of the Nipple
.
b Place one Lock Washer over the top end of the Nipple
and then thread the Nipple into the center lock hole of
the Crossbar
.,
c Using pliers thread the Hex Nut against the crossbar
and hand tighten until snug
.
d Thread another Hex Nut onto the bottom end of the
Nipple
.
.
.
STEP 8:
a Adjust the Fixture Chain to your desired length by
.
removing the links if needed
Please note that depends on chain material thickness
*,
you might be required to use chain pliers to spread links
open
.
b Pull the supply wires through the Fixture Chain alternating
.
links And then pull the wires through the following
.
components in turn
Canopy Lock Ring Ceiling Canopy Canopy Chain Loop,
Lock Washer and Nipple
c Place Lock Washer over the end of the Nipple and thread
.
:
,,
,.
the Canopy Chain Loop onto the end of the Nipple
d Using plier thread the Hex Nut against the Canopy Chain
.,
Loop and tighten until snug
e Attach one end of the Fixture Chain onto the Fixture Loop
.
and attach the another end of the chain onto the Canopy
Chain Loop
f Refer to Step 9 Wire Connections to connect wires
.- .
g Push the Ceiling Canopy upward over the Outlet Box
..
h Thread the Canopy Lock Ring onto the Canopy Chain Loop
.
.
and tighten until snug to secure the Ceiling Canopy
.
.
STYLE NUMBER LR5005RZ:
Lock Washer
Crossbar
Nipple
Lock Washer
Hex Nut
Nipple
Hex Nut
Hex Nut
Canopy Chain Loop
.
Ceiling
Canopy
Fixture Chain
.
4OF5
Canopy Lock Ring
Fixture Loop
Page 5
INSTALLATION INSTRUCTIONS
STEP 9:
Use Wire Connectors not supplied to connect the
*()
wires
.
a Connect the House Ground Wire to the Fixture Ground
.
Wire.
.()
b Connect the House White or Ribbed Wire to the
Fixture Supply Wire White or Ribbed Side .
.()
c Connect the House Black or Red Wire to the Fixture
Supply Wire Black or Smooth Side
.
d Wrap each connection with approved electrical tape and
().
()
carefully stuff all of the connected wires into the Outlet
.
Box
STEP 10:
a Place the Candle Cover over the Socket as shown..
STYLE NUMBER LR5005RZ:
WHITE OR RIBBED
FROM HOUSE
BLACK OR RED WIRE()
FROM HOUSE
GROUND WIRE GROUND WIRE
FROM HOUSE FROM FIXTURE
WHITE OR RIBBED
FROM FIXTURE
BLACK OR SMOOTH
FROM FIXTURE
Candle Cover
Socket
STEP 11:
.a Install correct bulbs referring to fixture markings and/or labels for maximum wattage.
Your installation is completed now. Restore electricity. Retain this sheet for future reference.
5OF5
Loading...