Quoizel KY540IB User Manual
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
INSTRUCTION SHEET IS KY540STYLE NUMBER KY540K KY540IB:,
PACKAGE CONTENTS
Part
Crossbar
A
Green Ground Screw
B
Lock Washer
C
Hex Nut
D
Nipple
E
Ceiling Canopy
F
Fixture Chain
G
Lock Ball
H
Shade
I
Fixture Assembly
J
!
WARNINGS AND CAUTIONS
WARNING:
● Before beginning the installation, turn off electricity at the circuit breaker box or the main fuse box by
switching off the circuit breaker or removing the fuse.
CAUTIONS:
● These instructions are provided for your safety. It is very important that they are read completely before
the installation of your fixture. We strongly recommend that a professional electrician install the fixture.
● Disconnect fixture from the power source before replacing the bulb(s), making sure the bulb(s) had
sufficient time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may
result.
Description
Quantity
1pc
1pc
2pcs
3pcs
1pc
1pc
2pcs
1pc
5pcs
1pc
ISSUED 07-2008
A
B
C
D
E
Revised 2010-01-05
F
G
H
I
J
PREPARATION
● Before beginning installation of product, make sure all parts are present. Compare parts with package
contents list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or
operate the product. Contact customer service for replacement part.
● Estimated Assembly Time: 15 30 minutes
● Tools Required forAssembly (not included): Flathead screwdriver Phillips screwdriver, pliers, electrical
tape, wire cutters, safety glasses &5, 100 Watt, Type A Medium Base Bulbs.
● Helpful Tools (not included): Wire Strippers.
INSTALLATION INSTRUCTIONS
STEP 1:
a Determine the hanging height of the fixture and adjust
.
the Fixture Chain
b Attach one ends of the Fixture Chains onto the Ceiling
.
Loop And then attach the other ends of the Fixture
.
Chains onto the Fixture Loop
.
,
-
:
Ceiling
Canopy
Ceiling Loop
Fixture Chain
.
Fixture
Loop
1of3
INSTALLATION INSTRUCTIONS
STEP 2:
a Secure the Crossbar onto the Outlet Box with Outlet Box
.
Screws Tighten until snug
..
STEP 3:
Plier is required on this step
*
a
..
Thread one Hex Nut onto top end of the Nipple
b
.
Place one Lock Washer over the top end of the Nipple
and then thread the Nipple into the center lock hole of
the Crossbar
c ing c
.,
Us plier thread the Hex Nut against the rossbar
and hand tighten until snug
d
.
Thread another Hex Nut onto the bottom end of the
Nipple
.
.
.
STYLE NUMBER KY540K KY540IB:,
Outlet Box
Crossbar
Outlet Box
Screw
.
Lock Washer
Hex Nut
Crossbar
Nipple
Hex Nut
STEP 4:
a Locate the Ceiling Canopy onto the Crossbar and slip the
.
Button Stop on the end of Lanyard into the Slot on the
Crossbar as shown.
STEP 5:
*()
Use Wire Connectors not supplied to connect the
.
wires
.
a Connect the House Ground Wire to the Fixture Ground
Wire.
.()
b Connect the House White or Ribbed Wire to the
Fixture Supply Wire White or Ribbed Side .
.()
c Connect the House Black or Red Wire to the Fixture
Supply Wire Black or Smooth Side
.
d Wrap each connection with approved electrical tape and
().
()
carefully stuff all of the connected wires into the Outlet
.
Box
WHITE OR RIBBED
FROM HOUSE
BLACK OR RED WIRE()
FROM HOUSE
GROUND WIRE GROUND WIRE
FROM HOUSE FROM FIXTURE
Crossbar
Slot
Button Stop
Lanyard
Ceiling Canopy
WHITE OR RIBBED
FROM FIXTURE
BLACK OR SMOOTH
FROM FIXTURE
2of3
Loading...