Quoizel KY5103IB User Manual

6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com

. .

, .

INSTRUCTION SHEET IS KY5103­STYLE NUMBER KY5103IB:

PACKAGECONTENTS

Description

Part

Crossbar

A

Green Ground Screw

B

Lock Washer

C

Hex Nut for mounting( )

D

Nipple

E

Ceiling Canopy

F

Canopy Lock Ring

G

Ceiling Canopy Loop

H

Fixture Chain

I

Fixture Loop

J

K

Lock Screw

L

Shade

M

Fixture Assembly

Quantity
1pc

1pc
2pcs
2pcs
1pc
1pc
1pc
1pc
1pc
1pc
12pcs
3pcs
1pc

Revised 11 28-2008-

A

B
C
D
E

F

G

H

I

J

K

L

M

!

WARNINGSANDCAUTIONS

WARNING:

● Before beginning the installation, turn off electricity at the circuit breaker box or the main fuse box by

switching off the circuit breaker or removing the fuse.
CAUTIONS:

● These instructions are provided for your safety. It is very important that they are read completely before the

installation of your fixture. We strongly recommend that a professional electrician install the fixture.

● Disconnect fixture from the power source before replacing the bulb(s), making sure the bulb(s) had sufficient

time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may result.

PREPARATION

Before beginning installation of product, make sure all parts are present. Compare parts with package

●

contents list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or
operate the product. Contact customer service for replacement part.

● Estimated Assembly Time: 15 30 minutes

● Tools Required for Assembly(not included): Flathead Screwdriver Phillips Screwdriver, Pliers, Electrical

Tape, Wire Cutters, Safety Glasses &3,100 Watt, Type - A Medium Base Bulbs.

● Helpful Tools(not included): Wire Strippers.

-

,

,

1 OF 3

ASSEMBLYINSTRUCTIONS

STYLE NUMBER KY5103IB:

STEP 1 :

a Thread the Fixture Loop onto the nipple on the top

.

center of the Fixture Canopy Hand tighten until snug

. .

STEP 2:

a Secure the Crossbar onto the Outlet Box with Outlet

.

Box Screws Tighten until snug

. .

STEP 3:

* .

Plier is required on this step

. .

a Thread one Hex Nut onto top end of the Nipple

.

b Place one Lock Washer over the top end of the Nipple

and then thread the Nipple into the center lock hole of
the Crossbar

. ,

c Using plier thread the Hex Nut against the Crossbar

and hand tighten until snug

.

d Thread another Hex Nut onto the bottom end of the

Nipple

.

.

.

Crossbar

Fixture Loop

Fixture
Canopy

Outlet Box

Crossbar

Outlet Box
Screw

Lock Washer

Hex Nut

Nipple

STEP 4:

a Adjust the Fixture Chain to your desired length by

.

removing the links if needed

Please note that depends on chain material thickness

* ,

you might be required to use chain pliers to spread
links open

b Pull the supply wires through the Fixture Chain

.

alternating links And then pull the wires through the

.

.

following components in turn

Canopy Lock Ring Ceiling Canopy Canopy Chain

Loop Lock Washer and Nipple

, , .

c Place Lock Washer over the end of the Nipple and

.

, ,

thread the Canopy Chain Loop onto the end of the
Nipple

d Use plier thread the Hex Nut against the Canopy

. ,

.

Chain Loop and tighten until snug

e Attach one end of the Fixture Chain onto the Fixture

.

Loop and attach the another end of the chain onto the
Canopy Chain Loop

f Refer to Step Wire Connections to connect wires

. - .

g Push the Ceiling Canopy upward over the Outlet Box

. .

h Thread the Canopy Lock Ring onto the Canopy Chain

.

.

5

Loop and tighten until snug to secure the Ceiling
Canopy

.

.

:

.

Hex Nut

Nipple

Hex Nut

Lock Washer

Canopy Chain Loop

Ceiling Canopy

Fixture Chain

Canopy Lock Ring

Fixture Loop

2 OF 3