Quoizel KY1716IB User Manual
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
INSTRUCTION SHEET IS KY1716STYLE NUMBER KY1716IB:
PACKAGE CONTENTS
Part
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
Crossbar
Green Ground Screw
Mounting Screw
Lock Washer (for #8-32 Screw)
Hex Nut (for #8-32 Screw)
Mounting Ball
Plastic Washer
Flat Washer
Hex Nut (1/8IP)
Cap
Finial
Fixture Assembly
Nipple with Hex Nut
Spacer Tube
Check Ring
Shade Stop
Shade
Description
Quantity
1pc
1pc
2pcs
2pcs
2pcs
2pcs
1pc
1pc
1pc
1pc
1pc
1pc
1pc
1pc
1pc
1pc
1pc
ISSUED 03-2010 REVISED 2010-05-05
A
B
C
D
E
F
G
H
I
J
M
N
O
P
L
Q
!
WARNINGS AND CAUTIONS
WARNING:
●
Before beginning the installation, turn off electricity at the circuit breaker box or the main fuse box by
switching off the circuit breaker or removing the fuse.
CAUTION:
●
These instructions are provided for your safety. It is very important that they are read completely before
the installation of your fixture. We strongly recommend that a professional electrician install the fixture.
●
Disconnect fixture from the power source before replacing the bulb(s), making sure the bulb(s) had
sufficient time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may
result.
PREPARATION
●
Before beginning installation of product, make sure all parts are present. Compare parts with package
contents list and diagram above. If any part is missing or damaged, do not attempt to assemble, install
or operate the product. Contact customer service for replacement part.
●
Estimated Assembly Time : 20 30 minutes
●
Tools Required for Assembly (not included) : Flathead Screwdriver Phillips Screwdriver, Pliers,
Electrical Tape, Wire Cutters, Safety Glasses &3, 100 Watt, Type - A Medium Base Bulbs.
●
Helpful Tools (not included) : Wire Strippers.
K
,
1OF3
INSTALLATION INSTRUCTIONS
STYLE NUMBER KY1716IB:
STEP 1:
.,
a Screw the Mounting Screws into the Crossbar place the
Mounting Screw
Crossbar
Lock Washers over the Mounting Screws and thread the
Hex Nuts onto the Mounting Screws as shown Secure the
.
position of the Mounting Screws by tightening the Hex
Nuts against the Crossbar
b Secure the Crossbar to the Outlet Box with Outlet Box
.
Screws
.
.
Outlet Box
Outlet Box Screw
STEP 2:
a Fixture Canopy. Locate the onto the Crossbar and slip the
Button Stop on the end of Lanyard into the Slot on the
Crossbar as shown.
Slot
Fixture
Canopy
Hex Nut
Lock Washer
Crossbar
Button Stop
Lanyard
STEP 3:
*()
Use Wire Connectors not supplied to connect the
.
wires
.
a Connect the House Ground Wire to the Fixture Ground
WHITE OR RIBBED
FROM HOUSE
Wire.
.()
b Connect the House White or Ribbed Wire to the
Fixture Supply Wire White or Ribbed Side .
.()
c Connect the House Black or Red Wire to the Fixture
Supply Wire Black or Smooth Side
.
d Wrap each connection with approved electrical tape and
().
()
carefully stuff all of the connected wires into the Outlet
.
Box
BLACK OR RED WIRE()
FROM HOUSE
GROUND WIRE GROUND WIRE
FROM HOUSE FROM FIXTURE
STEP 4 :
.a Place Fixture Canopy over the Mounting Screws and
thread the Mounting Balls onto the Mounting Screws to
secure the Fixture Canopy. Hand-tighten until snug.
WHITE OR RIBBED
FROM FIXTURE
BLACK OR SMOOTH
FROM FIXTURE
Crossbar
Mounting Screw
Fixture Canopy
Mounting Ball
2OF3
Loading...