Page 1
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
. .
, .
INSTRUCTION SHEET IS KY1507STYLE NUMBER KY1507IB:
PACKAGECONTENTS
Part
Description
Crossbar
A
B
Green Ground Screw
Mounting Screw
C
Lock Washer
D
Hex Nut (for Mounting Screw)
E
Mounting Ball
F
Lock Screw
G
H
6 Rod"
12 Rod"
I
Ceiling Canopy
J
Decorative Rod
K
L
Shade Holder Assembly
M
Shade
Quantity
1pc
1pc
2pcs
2pcs
2pcs
2pcs
4pcs
2pcs
2pcs
1pc
1pc
1pc
1pc
Revised 2008 12 11- -
J
A
B
C
D
E
F
G
H
K
L
I
!
WARNINGSANDCAUTIONS
WARNING:
● Before beginning the installation, turn off elec tric ity at the c ircu it bre aker box or the main f use box by
switching off the circuitbreaker or removing the fuse.
CAUTIONS:
● These instructions are pro vided for your s afety. It is very important that they are read completely before the
installation of your fixture. We are strongly recommend that a professional electrician install the fixture.
● Disconn ect fix ture fro m the power source before replacing the bulb(s), maki ng sure the bul b(s) had sufficient
time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may result.
PREPARATION
● Before beginning installation of pro duct, make sure all p arts are present. Compare parts with package
contents list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or
operate the product. Contact customer service for replacement part.
● Estimated Assembly Time: 10 20 minutes
● Tools Required for Ass embly (not inc luded): Flathead screwdriver Phillips screwdri ver, pli ers, electrical
tape, wire cutters, safety glasses &1, 100 Watts, Type A Medium Base Bulbs.
● Helpf ul Tools (no t included): Wire Strippers.
,
-
M
1 OF 3
Page 2
ASSEMBLYINSTRUCTIONS
STEP 1:
.
a Thread the end of the Decorative Rod onto the Nipple
on the top center of the Shade Holder Assembly Hand
tighten until snug
.
STEP 2:
.
a Determine the Rods to be assembled according to your
desired hanging height.
.
b Pass the Supply Wires with Ground Wire through the
chosen Rods and then thread Rods and Decorative Rod
together as shown. Tighten until snug.
STYLE NUMBER KY1507IB:
.
Decorative Rod
Shade Holder
Assembly
6” Rod
6” Rod
STEP 3:
.
a Pass the Supply Wires with Ground Wire through the
Swivel and Ceiling Canopy.
.
b Thread the Swivel onto the top end of the Upper Rod and
hand tighten until snug.
12” Rod
12” Rod
Supply Wires with
Ground Wire
Decorative Rod
Ceiling Canopy
Swivel
Supply Wire with
Ground Wire
2 OF 3
Upper Rod
Page 3
ASSEMBLYINSTRUCTIONS
STYLE NUMBER KY1507IB:
STEP 4:
a Screw the Mounting Screws into the Crossbar place the
. ,
Lock Washers over the Mounting Screws and thread the
Hex Nuts onto the Mounting Screws as shown Secure
.
the position of the Mounting Screws by tightening the Hex
Nuts against the Crossbar
b Secure the Crossbar to the Outlet Box with OutletBox
.
Screws
.
.
STEP 5:
* ( ) .
Use Wire Connectors not supplied to connect the wires
.
a Connect the House Ground Wire to the Fixture Ground
Wire.
.
b Connect the House White Wire to the Fixture Supply Wire
( )
White or Ribbed Side .
. ( )
c Connect the House Black or Red Wire to the Fixture
Supply Wire Black or Smooth Side
.
d Wrap each connection with approved electrical tape and
carefully stuff all of the connected wires into the Outlet
.
Box
( ) .
Outlet Box
WHITE WIRE
FROM HOUSE
BLACK OR RED WIRE( )
FROM HOUSE
GROUND WIRE
FROM HOUSE
Mounting Screw
Crossbar
Hex Nut
Lock Washer
Outlet Box Screw
WHITE OR RIBBED
FROM FIXTURE
BLACKOR SMOOTH
FROM FIXTURE
GROUND WIRE
FROM FIXTURE
STEP 6:
a Place the Ceiling Canopy over the Mounting Screws and
.
thread Mounting Balls onto the Mounting Screws to secure
it. Hand tighten until snug.
STEP 7:
a Locate the Shade inside of the Shade Holder Line up
. .
Holes on the Shade and Mounting Holes on the Shade
Holder Secure them together by threading Lock
Screws into the Mounting Holes on the Shade Holder
until the screws through the Holes on the Shade
.
.
Outlet Box
Mounting Screw
Ceiling Canopy
Mounting Ball
Shade Holder
Lock Screw
Mounting Hole
Hole
STEP 8
.
a Install correct Bulb referring to fixture markings and/or labels for maximum wattage.
:
Your installation is completed now.Restore electricity. Retain this sheet for future reference.
3 OF 3
Shade
Loading...