Quoizel KD5103MM User Manual

6 CORPORATE PARKWAY GOOSE CREEK SC 29445 www quoizel com
..
,.
INSTRUCTION SHEET IS KD5103­STYLE NUMBER KD5103MM:
PACKAGE CONTENTS
Part
A
B
C
D
E
F
G
H
I
J
K
L
N
O
P
Q
R
S
T
U
Crossbar
Green Ground Screw
Hex Nut Nipple
Lock Washer Canopy Chain Loop
Canopy Lock Ring
Fixture Chain Ceiling Canopy
Fixture Loop
Support Part Fixture Cover
Short Nipple
Lock Screw
Fixture Body Finial
Shade
Socket Collar
Diffuser
Fixture Assembly
Crystal Pendants
A) - 78 mm Crystal Pendant [3pcs]
B) - 50 mm Crystal Pendant [3pcs]
Description
Quantity
1pc
1pc
2pcs
1pc
2pcs
1pc
1pc
1pc
1pc
1pc
1pc
1pc
1pc
3pcs
1pc
3pcs
3pcs
3pcs
3pcs
1pc
1pc
ISSUED 02-2010
A
Q
B
C
D
E
F
G
H
I
J
K
L
R
S
T
!
WARNINGS AND CAUTIONS
WARNING:
● Before beginning the installation, turn off electricity at the circuit breaker box or the main fuse box by switching off the circuit breaker or removing the fuse.
CAUTIONS:
● These instructions are provided for your safety. It is very important that they are read completely before the installation of your fixture. We strongly recommend that a professional electrician install the fixture.
● Disconnect fixture from the power source before replacing the bulb(s), making sure the bulb(s) had sufficient time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may result.
PREPARATION
● Before beginning installation of product, make sure all parts are present. Compare parts with package contents list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or operate the product. Contact customer service for replacement part.
● Estimated Assembly Time: 30 45 minutes
● Tools Required for Assembly (not included): Flathead screwdriver Phillips screwdriver, Pliers, Electrical tape, Wire cutters, Safety glasses & (3) 60W A19 medium base bulbs.
● Helpful Tools (not included): Wire strippers.
N
O
P
U
A)
­,
B)
1OF4
INSTALLATION INSTRUCTIONS
STYLE NUMBER KD5103MM:
STEP 1:
a Unfold Side Arms at 120 degree locations.
.
b Place the Fixture Body onto the top of the Fixture
.
Assembly, line up holes on the side of it and mounting holes on the Side Arms. Secure them together by threading Lock Screws into the mounting holes on the Side Arms. Hand-tighten until snug.
STEP 2:
a Screw the Short Nipple into the top end of the Fixture
.
Assembly and tighten until snug.
b Pass the Fixture Cover and the Support Part over the top
.
end of the Short Nipple. Secure by threading the Fixture Loop onto the nipple. Hand-tighten until snug.
Side Arm
Lock Screw
Fixture Body
Fixture Assembly
Fixture Loop
Support Part
Fixture Cover
STEP 3:
a Secure the Crossbar onto the Outlet Box with Outlet Box
.
Screws Tighten until snug
..
Short Nipple
Fixture Assembly
Outlet Box
Crossbar
Outlet Box Screw
2OF4
INSTALLATION INSTRUCTIONS
STEP 4:
*.
Pliers is required on this step
..
a Thread one Hex Nut onto top end of the Nipple
.
b Place one Lock Washer over the top end of the Nipple
and then thread the Nipple into the center lock hole of the Crossbar
.,
c Using pliers thread the Hex Nut against the crossbar
and hand tighten until snug
.
d Thread another Hex Nut onto the bottom end of the
Nipple
.
.
.
STEP 5:
a Adjust the Fixture Chain to your desired length by
.
removing the links if needed
Please note that depends on chain material thickness
*,
you might be required to use chain pliers to spread links open
.
b Pull the supply wires through the Fixture Chain alternating
.
links And then pull the wires through the following
.
components in turn Canopy Lock Ring Ceiling Canopy Canopy Chain Loop, Lock Washer and Nipple
c Place Lock Washer over the end of the Nipple and thread
.
:
,,
,.
the Canopy Chain Loop onto the end of the Nipple
d Using plier thread the Hex Nut against the Canopy Chain
.,
Loop and tighten until snug
e Attach one end of the Fixture Chain onto the Fixture Loop
.
and attach the another end of the chain onto the Canopy Chain Loop
f Refer to Step 6 Wire Connections to connect wires
.- .
g Push the Ceiling Canopy upward over the Outlet Box
..
h Thread the Canopy Lock Ring onto the Canopy Chain Loop
.
.
and tighten until snug to secure the Ceiling Canopy
.
.
STYLE NUMBER KD5103MM:
Lock Washer
Crossbar
Nipple
Lock Washer
Hex Nut
Nipple
Hex Nut
Hex Nut
Canopy Chain Loop
.
Ceiling Canopy
Fixture Chain
.
Canopy Lock Ring
STEP 6:
*()
Use Wire Connectors not supplied to connect the
.
wires
.
a Connect the House Ground Wire to the Fixture Ground
Wire.
.()
b Connect the House White or Ribbed Wire to the
Fixture Supply Wire White or Ribbed Side .
.()
c Connect the House Black or Red Wire to the Fixture
Supply Wire Black or Smooth Side
.
d Wrap each connection with approved electrical tape and
().
()
carefully stuff all of the connected wires into the Outlet
.
Box
3OF4
WHITE OR RIBBED
FROM HOUSE
BLACK OR RED WIRE()
FROM HOUSE
GROUND WIRE GROUND WIRE
FROM HOUSE FROM FIXTURE
Fixture Loop
WHITE OR RIBBED
FROM FIXTURE
BLACK OR SMOOTH
FROM FIXTURE
INSTALLATION INSTRUCTIONS
STEP 7:
.a Place the Shade over the Socket and secure with the
Socket Collar. Hand-tighten until snug.
STEP 8:
.a Install the correct bulbs referring to fixture markings and/or labels for maximum wattage.
STEP 9:
a Place the Diffuser over the Bolt in the bottom center of the
.
Shade. Secure by threading the Finial onto the Bolt. Hand­tighten gently until snug.
STYLE NUMBER KD5103MM:
Socket
Socket Collar
Shade
STEP 10:
a Attach 50mm Crystal Pendant onto the hanger on the top
.
end of the Support Arm.
b78
. Attach mm Crystal Pendant onto the hanger on the
bottom
end of the Support Arm.
Shade
Diffuser
Bolt
50mm Crystal Pendant
Harp
Finial
Support Arm
78mm Crystal Pendant
Your installation is completed now. Restore electricity. Retain this sheet for future reference.
4OF4
Loading...