Page 1
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
. .
, .
INSTRUCTION SHEET IS KD5009-
STYLE NUMBER KD5009MM:
PACKAGECONTENTS
Part
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
Nipple (include in Mounting Kits)
Description
Crossbar
Green Ground Screw
Hex Nut
Lock Washer
Canopy Chain Loop
Canopy Lock Ring
Fixture Chain
Ceiling Canopy
Shade
Candle Cover
Fixture Loop
Nipple
Support Part
Cover
Fixture Body
Lock Screw
Finial
Crystal
Quantity
1pc
1pc
2pcs
1pc
2pcs
1pc
1pc
1pc
1pc
9pcs
9pcs
1pc
1pc
1pc
1pc
1pc
6pcs
1pc
16pcs
ISSUED 07-2008 Revised2008-09-02
A
B
C
D
E
F
G
H
I
J
K
M
N
O
P
Q
R
S
L
!
WARNINGSANDCAUTIONS
WARNING:
● Before beginning the instal lation, turn off electricity at the circuit breaker box or the main fuse box by
switching off the circuit breaker or removing the fuse.
CAUTIONS:
● These instructions are provided for your safety. It is very i mpo rtant that they are read completely b efo re the
installation of your fixture. We strongly recommend that a professional electrician install the fixture.
● Disconnect fixture from the pow er source before replacing the bulb(s), making sure t he bulb(s) had suffi cient
time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may result.
PREPARATION
● Before beginning installation of product, make sure all parts are present. Compar e parts with pac kage
contents list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or
operate the product. Contact customer service for replacement part.
● Est imated Assembly Time: 30 45 minutes
● Tool s Required for Assembly (not include d): Flathea d s crewdriver Phill ips screwdriver, pliers, ele ctrical
tape, wire cutters, safety glasses &9, 60 Watt, Type B Candelabra Base Bulbs.
● Helpful Tools (not included) : Wire Stripp ers.
,
-
1 OF 5
Page 2
INSTALLATION INSTRUCTIONS
STEP 1:
a Unfold Support Arms to proper locations. Match
.
the Mounting Holes on Support Arms onto the holes
on the side of the Fixture Body.
b. Thread Lock Screws inside of Mounting Holes to
secure Support Arms as shown.
STYLE NUMBER KD5009MM:
Lock Screw
Fixture Body
Mounting Hole
SupportArm
STEP 2:
a Thread one end of the Nipple into the Hex Coupling
.
in the center of the Fixture Body. Hand tighten until
snug.
b. Place the Cover and the Support Part over the top
end of the Nipple. Secure them by threading
Fixture Loop onto the Nipple and tighten until snug.
STEP 3:
a Thread the Finial onto the nipple on the bottom
.
center of the Lower Junction Box Hand tighten
until snug
.
.
Fixture Loop
Support Part
Cover
Nipple
Hex Coupling
Fixture Body
2 OF 5
Lower Junction Box
Finial
Page 3
INSTALLATION INSTRUCTIONS
STEP 4:
a Place Crystals onto Hangers on Support Arms and
.
Finial as shown.
STYLE NUMBER KD5009MM:
Hanger
Crystal
SupportArm
Crystal
STEP 5:
a Secure the Crossbar onto the Outlet Box with
.
Outlet Box Screws Tighten until snug
. .
STEP 6:
*
Plier is required on this step
. .
Thread one Hex Nut onto top end of the Nipple
a
.
Place one Lock Washer over the top end of the
b
Nipple and then thread the Nipple into the
center lock hole of the Crossbar
. ,
Us plier thread the Hex Nut against the
c ing
rossbar and hand tighten until snug
c
.
Thread another Hex Nut onto the bottom end of
d
the Nipple
.
.
.
.
Finial
Crystal
Crossbar
Crystal
Outlet Box
Crossbar
Outlet BoxScrew
Lock Washer
Hex Nut
Nipple
3 OF 5
Hex Nut
Page 4
INSTALLATION INSTRUCTIONS
STEP 7:
a Adjust the Fixture Chain to your desired length by
.
removing the links if needed
Please note that depends on chain material
*
thickness you might be required to use chain
,
pliers to spread links open
b Pull the supply wires through the Fixture Chain
.
alternating links And then pull the wires through
.
the following components in turn
Canopy Lock Ring Ceiling Canopy Canopy
, ,
Chain Loop, Lock Washer and Nipple
c Place Lock Washer over the end of the Nipple and
.
thread the Canopy Chain Loop onto the end of the
Nipple
d Using plier thread the Hex Nut against the
. ,
.
Canopy Chain Loop and tighten until snug
e Attach one end of the Fixture Chain onto the
.
Fixture Loop and attach the another end of the
chain onto the Canopy Chain Loop
f Refer to Step 8 Wire Connections to connect
. -
wires
.
g Push the Ceiling Canopy upward over the Outlet
.
Box
.
h Thread the Canopy Lock Ring onto the Canopy
.
Chain Loop and tighten until snug to secure the
Ceiling Canopy
.
.
.
:
, .
.
STYLE NUMBER KD5009MM:
Nipple
Hex Nut
Lock Washer
Canopy Chain Loop
Ceiling Canopy
.
Fixture Chain
Canopy Lock Ring
Fixture Loop
STEP 8:
* ( )
Use Wire Connectors not supplied to connect
the wires
.
a Connect the House Ground Wire to the Fixture
Ground Wire.
.
b Connect the House White Wire to the Fixture
Supply Wire White or Ribbed Side .
. ( )
c Connect the House Black or Red Wire to the
Fixture Supply Wire Black or Smooth Side
.
d Wrap each connection with approved electrical
tape and carefully stuff all of the connected wires
into the Outlet Box
.
( )
( ).
.
WHITE WIRE
FROM HOUSE
BLACK OR RED WIRE( )
FROM HOUSE
GROUND WIRE
FROM HOUSE
WHITE OR RIBBED
FROM FIXTURE
BLACK OR SMOOTH
FROM FIXTURE
GROUND WIRE
FROM FIXTURE
4 OF 5
Page 5
INSTALLATION INSTRUCTIONS
STEP 9:
a Place the Candle Cover over the Socket set
. ,
into the Cup And then place the Harp inside of
the Shade onto the top end of the Candle Cover
.
STYLE NUMBER KD5009MM:
.
Harp
Candle
Cover
Cup
Shade
Socket
STEP 10
.
a Install correct Bulbs referring to fixture markings and/or labels for maximum wattage.
:
Your installation is completed now. Restore electricity. Retain this sheet for future reference.
5 OF 5
Loading...