6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
INSTRUCTION SHEET IS-JLE2812
STYLE NUMBER: JLE2812IS
PACKAGE CONTENTS
PART
A Crossbar
B
C
D
E
F
G
H
I
J
K
L
M
N
DESCRIPTION
Green Ground Screw
Hex Nut
Nipple
Lock Washer
Canopy Chain Loop
Canopy Lock Ring
Fixture Chain
Ceiling Canopy
Socket Assembly
Fixture Loop
Center Column
Side Chain
Crystal
QUANTITY
1pc
1pc
3pcs
1pc
2pcs
1pc
1pc
1pc
1pc
1pc
1pc
1pc
12 pcs
36 pcs
ISSUED 03-2010 REVISED 2010-10-19
A
B
C
D
E
F
G
H
I
K
L
M
J
N
WARNINGS AND CAUTIONS
WARNING:
● Before beginning the installation, turn off electricity at the circuit breaker box or the main fuse box by switching
off the circuit breaker or removing the fuse.
CAUTION:
● These instructions are provided for your safety. It is very important that they are read completely before the
installation of your fixture. We strongly recommend that a professional electrician install the fixture.
● Disconnect fixture from the power source before replacing the bulb(s), making sure that bulb9s) had sufficient
time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may result.
1OF6
PREPARATION
STYLE NUMBER: JLE2812IS
● Before beginning installation of product, make sure all parts are present. Compare parts with package contents
list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or operate the
product. Contact customer service for replacement part.
● Estimated Assembly Time: 30 - 45 minutes
● Tool Required for Assembly (not included): Flathead screwdriver, Phillips screwdriver, Pliers, Electrical tape,
Wire cutter, Safety glasses and (3) 60W B10 candelabra base bulbs
.
● Helpful Tools (not included): Wire strippers.
INSTALLATION INSTRUCTIONS
STEP 1:
a. Screw the end of the Center Column into the Coupling
on the top center of the SocketAssembly. Please line
up the Pin Holes at the side of the Fixture Canopy and
the Pin Holes at the side of the Socket Assembly before
tighten them together.
Fixture
Canopy
Branch
Pin Hole
Center Column
Coupling
Branch
Pin Hole
Socket
Assembly
STEP 2:
a. Thread the Fixture Loop onto the nipple on the top end
of the Center Column. Hand-tighten until snug.
2OF6
Fixture Loop
Center Column
INSTALLATION INSTRUCTIONS
STEP 3:
a. Secure the Crossbar onto the Outlet Box with Outlet
Box Screws. Tighten until snug.
STEP 4:
a. Thread one Hex Nut onto top end of the Nipple.
b. Place one Lock Washer over the top end of the Nipple
and then thread the Nipple into the center lock hole of
the Crossbar.
c. Using pliers, thread the Hex Nut against the Crossbar
and hand-tighten until snug.
Crossbar
STYLE NUMBER: JLE2812IS
Outlet Box
Crossbar
Outlet Box
Screw
Lock Washer
Hex Nut
STEP 5:
a. Thread another Hex Nut onto the end of the Nipple.
b. Place the Lock Washer over the end of the Nipple and
then thread the Canopy Chain Loop onto the end of the
Nipple.
c. Using pliers, thread the Hex Nut against the Canopy
Chain Loop and hand-tighten until snug.
Nipple
Nipple
Hex Nut
Lock Washer
Canopy Chain Loop
3OF6
INSTALLATION INSTRUCTIONS
STEP 6:
a. Push the Ceiling Canopy upward over the Outlet Box.
Thread the Canopy Lock Ring onto the Canopy Chain
Loop and tighten until snug to secure the Ceiling
Canopy.
STEP 7:
a. Adjust the Fixture Chain to your desired length by
removing the links if needed. You may need to use
pliers to open the chain links. If so, put a cloth over the
chain to protect the finish from the pliers.
b. Attach one end of the Fixture Chain onto the Canopy
Chain Loop and then attach the other end of the Fixture
Chain onto the Fixture Loop on the top of the fixture.
STYLE NUMBER: JLE2812IS
Outlet Box
Canopy Chain Loop
Ceiling Canopy
Canopy Lock Ring
Canopy Chain Loop
Fixture Chain
Supply Wires
Fixture Loop
4OF6
INSTALLATION INSTRUCTIONS
STEP 8:
a. Pull the Supply Wires up through the Fixture Chain
alternating links. Push the wires up through the Canopy
Chain Loop into the outlet box.
STYLE NUMBER: JLE2812IS
Canopy Chain Loop
Fixture Chain
Supply Wires
STEP 9:
a. Un-thread the Canopy Lock Ring and slide Canopy
Lock Ring and Ceiling Canopy down the Fixture Chain.
b. Push all slack fixture wire through Canopy Chain Loop
into Outlet Box. Trim excess fixture wire leaving a
minimum of 6 in. Hanging out of the Outlet Box.
c. Refer to STEP 10 to connect the wires.
d. Re-attach the Ceiling Canopy as shown in STEP 6.
Outlet Box
Canopy Chain Loop
Fixture Chain
Ceiling Canopy
Canopy Lock Ring
5OF6
INSTALLATION INSTRUCTIONS
STEP 10:
Use Wire Connectors to connect the wires.
a. Connect the House Ground Wire to the Fixture Ground
Wire.
b. Connect the House White (or Ribbed) Wire to the
Fixture Supply Wire (Black or Smooth Side).
c. Connect the House Black (or Red) Wire to the Fixture
Supply Wire (Black or Smooth Side).
d. Wrap each connection with approved electrical tape
and carefully stuff all of the connected wires into the
Outlet Box.
WHITE OR RIBBED
FROM HOUSE
BLACK (OR RED) WIRE
FROM HOUSE
GROUND WIRE
STYLE NUMBER: JLE2812IS
WHITE OR RIBBED
FROM FIXTURE
BLACK OR SMOOTH
FROM FIXTURE
GROUND WIRE
FROM HOUSE
STEP 11:
a. Install correct bulbs referring to fixture markings and/or labels for maximum wattage.
STEP 12:
a. Attach one end of the Side Chain to the Pin Hole on the
side of the Fixture Canopy. Attach the another end of
the Side Chain to the Pin Hole on the side of the Cage.
b. Attach Crystals to the Branches as shown.
Branch
Crystal
Fixture Canopy
FROM FIXTURE
Pin Hole
Side
Chain
Branch
Crystal
Your installation is completed now. Restore electricity. Retain this sheet for future reference.
6OF6
Pin Hole
Cage
Loading...