Page 1
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
. .
, .
INSTRUCTION SHEET IS IE1717STYLE NUMBER IE1717BN:
PACKAGE CONTENTS
Part
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Crossbar
Green Ground Screw
Mounting Screw
Lock Washer
Hex Nut (for Mounting Screw)
Mounting Ball
Flat Washer
Rubber Washer
Hex Nut (1/8I.P.)
Stem with Hex Nut
Cap
Finial
Lock Screw
Steel Ring
Fxiture Assembly
Shade
Description
Quantity
1pc
1pc
2pcs
2pcs
2pcs
2pcs
2pcs
2pcs
1pc
1pc
1pc
1pc
3pcs
1pc
1pc
1pc
ISSUED 06-2008 Revised 2009-05-31
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
!
WARNINGS AND CAUTIONS
WARNING:
● Befo re beginning the in stal la tion, tu rn off el ectricity at th e circuit breaker box or the ma in fuse box by
switching off the circuit breaker or removing the fuse.
CAUTIONS:
● These instructions are provided for your safe ty. It is very i mportant t hat they a re read completely before
the installation of your fixture. We strongly recommend that a professional electrician install the fixture.
● Di sconnect fixture from t he power source before replacing t he bulb( s), ma king sure t he bulb(s) had
sufficient time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may
result.
PREPARATION
● Befo re beginning in st allation of prod uct, make sure a ll parts are present. Comp ar e parts with p ac kage
contents list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or
operate the product. Contact customer service for replacement part.
● Estimated Assembly Time : 15 30 minutes
● Tools R equi red for Assembly (not included): Flath ea d s crew driver Phillips screwdriver, pliers, electrical
tape, wire cutters, safety glasses &2, 100 Watt, Type A Medium Base Bulbs.
● He lp ful Tools (not included): Wire Strippers.
,
-
1 OF 4
Page 2
INSTALLATION INSTRUCTIONS
STYLE NUMBER IE1717BN:
STEP 1:
a Unfold Side Arms at the 120 degree locations.
.
b. Refer to Figure 1, place Steel Ring over Socket
Cluster as arrow direction. (Refer to Figure
2)Match the holes on the Ring onto the Mounting
Holes on the Side Arms.
c. Using screwdriver, thread Lock Screws into the
Mounting Holes and tighten until snug to secure the
Steel Ring onto Side Arms.
STEP 2:
a Screw the Mounting Screws into the Crossbar
. ,
place the Lock Washers over the Mounting Screws
and thread the Hex Nuts onto the Mounting Screws
as shown Secure the position of the Mounting
Screws by tightening the Hex Nuts against the
Crossbar
b Secure the Crossbar to the Outlet Box with Outlet
.
Box Screws
.
.
.
Steel
Ring
Mounting Hole
Lock Screw
Figure 1
Socket
Cluster
Figure 2
Side Arm
Steel Ring
Mounting Screw
Crossbar
Hex Nut
Lock Washer
STEP 3:
* ( )
Use Wire Connectors not supplied to connect
the wires
.
a Connect the House Ground Wire to the Fixture
Ground Wire.
.
b Connect the House White Wire to the Fixture
Supply Wire White or Ribbed Side .
. ( )
c Connect the House Black or Red Wire to the
Fixture Supply Wire Black or Smooth Side
.
d Wrap each connection with approved electrical
tape and carefully stuff all of the connected wires
into the Outlet Box
.
( )
( ).
.
Outlet Box
WHITE WIRE
FROM HOUSE
BLACK OR RED WIRE( )
FROM HOUSE
GROUND WIRE
FROM HOUSE
Outlet Box Screw
WHITE OR RIBBED
FROM FIXTURE
BLACK OR SMOOTH
FROM FIXTURE
GROUND WIRE
FROM FIXTURE
2 OF 4
Page 3
INSTALLATIONINSTRUCTIONS
STEP 4:
a Carefully tuck all wires into the wall mounted outlet
.
box and position the fixture over the outlet box.
b Align the holes in the Ceiling Canopy with the
.
Mounting Screws attached to the Crossbar.
c Pass the fixture over the Mounting Screws and
.
secure by threading Mounting Balls onto end of
screw. Tighten until snug.
STEP 5:
a Thread the Beaded end of the Stem into the
.
Coupling underside of the Socket Cluster. Hand
tighten until snug.
STYLE NUMBER IE1717BN:
Outlet Box
Mounting Screw
Ceiling Canopy
Mounting Ball
STEP 6:
a. Adjust the Hex Nut on the bottom end of the Stem to
proper location for rest components.
b. Place the following components over the end of the
Stem in turn:
Flat Washer, Rubber Washer, Shade, Rubber
Washer and Flat Washer.
c. Thread Hex Nut onto the end of the Stem and
tighten gently until snug to secure the above parts.
Socket Cluster
Coupling
Stem with Hex Nut
Stem with Hex Nut
3 OF 4
Flat Washer
Rubber Washer
Shade
Rubber Washer
Flat Washer
Hex Nut
Page 4
INSTALLATION INSTRUCTIONS
STEP 7:
a Place the Cap over the end of the Stem and secure
.
with the Finial. Hand tighten until snug.
STEP 8:
a Install correct Bulbs referring to fixture markings and/or labels for maximum wattage.
.
Your installation is completed now. Restore electricity. Retain this sheet for future reference.
STYLE NUMBER IE1717BN:
Stem
Cap
Finial
4 OF 4
Loading...