Quoizel GF1717AN User Manual

6 CORPORATE PARKWAY GOOSE CREEK SC 29445 www quoizel com
..
INSTRUCTION SHEET IS GF1717:­STYLE NUMBER GF1717AN,GF1717PN:
PACKAGE CONTENTS
Part
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Crossbar
Green Ground Screw Mounting Screws
Lock Washer Hex Nut for Mounting Screw()
Mounting Ball
Lock Ball Hex Nut (1/8IP)
Flat Washer
Plastic Washer Cap
Finial Fixture Assembly
Ring
Shade Stem Assembly
Description
Quantity
1pc
1pc
2pcs
2pcs
2pcs
2pcs
3pcs
1pc
2pcs
2pcs
1pc
1pc
1pc
1pc
1pc
1pc
ISSUED 08-2009 Revised 2009-11-19
M
A
B
C
D
E
F
G
H
I
N
O
!
WARNINGS AND CAUTIONS
WARNING:
Before beginning the installation, turn off electricity at the circuit breaker box or the main fuse box by
switching off the circuit breaker or removing the fuse.
CAUTION:
These instructions are provided for your safety. It is very important that they are read completely before
the installation of your fixture. We strongly recommend that a professional electrician install the fixture.
Disconnect fixture from the power source before replacing the bulb(s), making sure the bulb(s) had sufficient time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may result.
PREPARATION
Before beginning installation of product, make sure all parts are present. Compare parts with package
contents list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or operate the product. Contact customer service for replacement part.
Estimated Assembly Time : 30 45 minutes
Tools Required for Assembly (not included) : Flathead Screwdriver Phillips Screwdriver, Pliers, Electrical Tape, Wire Cutters, Safety Glasses &3, 100 Watt, Type - A Medium Base Bulbs.
Helpful Tools (not included) : Wire Strippers.
J
K
L
­,
P
1OF3
INSTALLATION INSTRUCTIONS
STEP 1:
a Unfold Support Arms at 120 degree locations as shown..
STEP 2:
a Locate the holes on the Ring over the Bolts on the ends of
.
Support Arms. Secure by threading Lock Balls onto the Bolts. Hand tighten until snug.
STYLE NUMBER GF1717AN,GF1717PN:
Support
Arm
120 Degree
SupportArm
Bolt
Lock Ball
Ring
STEP 3:
a Screw the Mounting Screws into the Crossbar place the
.,
Mounting Screw
Crossbar
Lock Washers over the Mounting Screws and thread the Hex Nuts onto the Mounting Screws as shown Secure the
.
position of the Mounting Screws by tightening the Hex Nuts against the Crossbar
b Secure the Crossbar to the Outlet Box with Outlet Box
.
Screws
.
.
Outlet Box
Outlet Box Screw
STEP 4:
*()
Use Wire Connectors not supplied to connect the
.
wires
.
a Connect the House Ground Wire to the Fixture Ground
Wire.
.()
b Connect the House White or Ribbed Wire to the
Fixture Supply Wire White or Ribbed Side .
.()
c Connect the House Black or Red Wire to the Fixture
Supply Wire Black or Smooth Side
.
d Wrap each connection with approved electrical tape and
().
()
carefully stuff all of the connected wires into the Outlet Box
WHITE OR RIBBED
FROM HOUSE
BLACK OR RED WIRE()
FROM HOUSE
GROUND WIRE GROUND WIRE
.
FROM HOUSE FROM FIXTURE
WHITE OR RIBBED
FROM FIXTURE
BLACK OR SMOOTH
FROM FIXTURE
Socket Assembly
Hex Nut
Lock Washer
2OF3
Loading...
+ 1 hidden pages