Quoizel GE5006SE User Manual

ASSEMBLY / INSTALLATION INSTRUCTIONS
6 CORPORATE PARKWAY GOOSE CREEK SC 29445 www quoizel com
..
CROSSBAR
SHAKE PROOF WASHER A
LOCK NUT A
NIPPLE
LOCK NUT B
SHAKE PROOF WASHER B
FIXTURE CHAIN
LOWER CEILING CANOPY
KNOB
ROD
SMALL LOOP
,.
FIGURE1
OUTLET BOX
HOUSE SUPPLY and
GROUND WIRES
OUTLET BOX SCREWS
not supplied()
GREEN GROUND SCREW
CANOPY CHAIN LOOP
FIXTURE SUPPLY and GROUND WIRE
UPPER CEILING CANOPY
CANOPY LOCK RING
FIXTURE SUPPLY and GROUND WIRE
FIXTURE LOOP
FIXTURE CANOPY
HEX COUPLING
FIXTURE COVER
CENTER STEM
SOCKET COLLAR
SOCKET
1 Before beginning the installation, carefully unpack and identify
.
all parts, referring to the illustration(FIGURE1).
2 Turn power to the installation point OFF at circuit breaker
..
3 Thread the end of CENTER STEM onto nipple on top center
.
of JUNCTION BODY Hand tighten until snug Locate top ends
..
of RODS through holes on FIXTURE COVER and thread KNOBS onto the top ends. Proceed to slide downwards and thread ends of RODS into SMALL LOOPS and hand tighten until snug.
4.Thread the nipple in the bottom center of FIXTURE CANOPY into HEX COUPLING in the center of FIXTURE COVER. Hand tighten until snug. Proceed to thread FIXTURE LOOP onto the nipple on the top center of FIXTURE CANOPY and tighten until snug.
5Fasten
.
(,)
For Canadian installations please refer to Page 2
the CROSSBAR to the OUTLET BOX with (2)OUTLET BOX SCREWS(not supplied). Proceed to thread LOCK NUT A and SHAKE PROOF WASHER A onto the top end of NIPPLE. Thread NIPPLE into the center of CROSSBAR. Locate the LOCK NUT B onto the bottom end of the NIPPLE. Tighten LOCK NUT A against CROSSBAR with plier until snug.
6. Locate the FIXTURE CHAIN and determine desired hanging
height of fixture. Adjust chain by removing links if needed. Please note that depending on chain material thickness, you might be required to use chain pliers to spread links open.
Proceed to attach one end of chain to FIXTURE LOOP, attached to top of fixture. Pass the fixture wires through FIXTURE CHAIN alternating links. Proceed to pass the fixture wires through the following mounting components in this order: 1)CANOPY LOCK
RING; 2)LOWER CEILING CANOPY; 3)UPPER CEILING
CANOPY; 4)CANOPY CHAIN LOOP; 5)SHAKE PROOF WASHER B.
7. (2 people recommended for the
Making the connections: remaining steps) Position the fixture under the ceiling mounted outlet box. Pass SHAKE PROOF WASHER B over the NIPPLE. Thread CANOPY CHAIN LOOP onto NIPPLE. Thread LOCK
NUT B down the NIPPLE, against the CANOPY CHAIN LOOP and
snug with pliers. Pass the wires through the NIPPLE. Take up
wire slack and trim wires so that approx. 6” will remain inside
outlet box. Proceed to attach the top of the FIXTURE CHAIN to the bottom of the CANOPY CHAIN LOOP. Using wire connectors (not supplied) connect the HOUSE GROUND WIRE to the
FIXTURE GROUND WIRE connect the HOUSE WHITE WIRE
;
to the FIXTURE SUPPLY WIRE (WHITE or RIBBED SIDE);
connect the HOUSE BLACK (or RED) WIRE to the FIXTURE SUPPLY WIRE(BLACK or SMOOTH SIDE). Wrap each connection with approved electrical tape.
8. With the proper connections made, proceed to push the LOWER CEILING CANOPY with UPPER CEILING CANOPY upward over the OUTLET BOX. Be sure that all wires are carefully tucked into the OUTLET BOX cavity. Secure canopies against ceiling by threading CANOPY LOCK RING onto the CANOPY LOOP. Tighten until snug.
JUNCTION BODY
.
9 Locate SHADE over SOCKET onto SHADE HOLDER Secure
by threading SOCKET COLLAR onto SOCKET and tighten
until snug Install bulbs referring to fixture markings and or
labels for maximum wattage
.
10 Restore power to the installation point ON. Retain this sheet
.
.
for future reference.
IF IN DOUBT ABOUT ELECTRICAL INSTALLATION, CONSULT A LICENSED ELECTRICIAN!
.
/
IS GE5006 Page1of3 01 06-.
6 CORPORATE PARKWAY GOOSE CREEK SC 29445 www quoizel com
..
FIGURE 2
COTTER PIN
HOUSE SUPPLY and GROUND WIRES
,.
3/8-18 NIPPLE, SHAKE PROOF WASHER AND HEX NUT (INCLUDED)
HOLE DRILLED INSIDE OUTLET BOX
OUTLET BOX
SET SCREWS
COUPLING
SHAKE PROOF WASHER A
LOCK NUT A
NIPPLE
LOCK NUT B
SHAKE PROOF WASHER B
CANOPY CHAIN LOOP
FIXTURE CHAIN
UPPER CEILING CANOPY
LOWER CEILING CANOPY
FIXTURE SUPPLY WIRE
INSTALLATION INSTRUCTIONS:
(FOR FIXTURES OVER 25 LBS. (Canada Only)
Please use the information outlined in this sheet for the ceiling installation part of your fixture assembly.
Quoizel recommends a licensed electrician or contractor be consulted for this installation.
1. Before installing fixture, carefully unpack and identify all parts referring to illustration FIGURE . Be sure the power to the installation point is OFF .
2.
(Refer to Figure 3, page 3) This weight of this fixture will require a means of support independent of the OUTLET BOX. This fixture must b supported by 3/8-18 NPSM NIPPLE(supplied) Th NIPPLE should be positioned so
e
e
that 3/4“ protrudes into the OUTLET BOX cavity.
opposite end of the NIPPLE must be attached to a structural or bridging member of sufficient strength to support the fixture weight. A COTTER PIN has been included and should be installed into the top of NIPPLE, above HEX NUT for added safety. A clearance hole must
be drilled on the inside top center of the OUTLET BOX Please refer to FIGURE 3 Page 3 for detailed illustration We recommend the consultation of a
.
,
licensed electrician or contractor due to the complexity of this installation
.
3. With the NIPPLE properly situated, locate COUPLING and proceed to thread onto the end of the NIPPLE protruding into the OUTLET BOX. Thread COUPLING onto pipe until tight. Tighten the top SET SCREW with pliers to secure COUPLING to NIPPLE.
4.
Making the connections:
(Quoizel recommends (2)
people for the rest of this installation)
the FIXTURE SUPPLY and GROUND WIRES. Locate the FIXTURE CHAIN and attach one end to the FIXTURE LOOP at the top of FIXTURE. Please note that depending on chain material thickness, you might be required to use chain pliers to spread chain links open. Proceed to pass the FIXTURE SUPPLY and GROUND WIRES through the chain, alternating links. Proceed the pass the wires through the following mounting components in this order: 1) CANOPY LOCK RING
2) LOWER CEILING CANOPY; 3)UPPER CEILING CANOPY;
4) CANOPY CHAIN LOOP; 5) SHAKE PROOF WASHER B and LOCKNUT B; 6) NIPPLE; 7) LOCK NUT A and SHAKE PROOF WASHER A Note Thread LOCK NUT A and B
approx ½ at each end of NIPPLE Position the fixture over
".
.:
the OUTLET BOX and pass the fixture wires through the bottom center of the COUPLING. Pull wires through the wire way hole on side of COUPLING. Proceed to thread the NIPPLE into the bottom center of the COUPLING until tight. Tighten the LOWER SET SCREW. Proceed to thread LOCK NUT A and SHAKE PROOF WASHER A up NIPPLE until seated against the bottom of the COUPLING. Tighten until snug with pliers. Using wire
connector (not supplied) connect the HOUSE GROUND WIRE to the FIXTURE GROUND WIRE; connect the HOUSE WHITE WIRE to the FIXTURE SUPPLY WIRE (WHITE or RIBBED SIDE); connect the HOUSE BLACK (or RED) WIRE to the FIXTURE SUPPLY WIRE (BLACK or SMOOTH SIDE). Wrap each connection with approved electrical tape.
5. With the proper connections made, p CANOPY CHAIN LOOP onto the bottom of the NIPPLE. Proceed to attach the top of the FIXTURE CHAIN to the bottom of the CANOPY CHAIN LOOP. Proceed to thread LOCK NUT B and SHAKE PROOF WASHER B down onto the top of the CANOPY CHAIN LOOP. Tighten and snug with pliers.
6. Proceed to push the LOWER CEILING CANOPY with UPPER CEILING CANOPY upward over the OUTLET BOX. Be sure that all wires are carefully tucked into the OUTLET BOX cavity. Secure canopies against ceiling by threading CANOPY LOCK RING onto the CANOPY LOOP. Tighten until snug.
7. Refer back to Page 1, Step 9 and finish installation.
2
at circuit breaker
Note: the
Proceed to unravel
roceed to thread the
.
CANOPY LOCK RING
IS GE5006 Page 2 of 3 01 06-.
Loading...
+ 1 hidden pages