Quoizel GE1507SE User Manual
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
. .
, .
INSTRUCTION SHEET IS GE1507STYLE NUMBER GE1507SE:
PACKAGE CONTENTS
Part
A
B
C
D
E
F
G
H
I
J
K
L
Crossbar
Green Ground Screw
Mounting Screw
Lock Washer
Hex Nut (for Mounting Screw)
Mounting Ball
SocketCollar
6” Rod
12 Rod"
Ceiling Canopy
SocketAssembly
Shade
Description
Quantity
1pc
1pc
2pcs
2pcs
2pcs
2pcs
1pc
2pcs
2pcs
1pc
1pc
1pc
ISSUED 11-2008
J
A
B
K
C
D
E
F
G
H
I
L
!
WARNINGS AND CAUTIONS
WARNING :
Before beginning the installation, turn off electricity at the circuit breaker box or the main fuse box by
●
switching off the circuit breaker or removing the fuse.
CAUTION :
These instructions are provided for your safety. It is very important that they are read completely
●
before the installation of your fixture. We strongly recommend that a professional electrician install the
fixture.
Disconnect fixture from the power source before replacing the bulb(s), making sure the bulb(s) had
●
sufficient time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may
result.
PREPARATION
●
Before beginning installation of product, make sure all parts are present. Compare parts with package
and diagram above. If any part is missing or damaged, do not attempt to assemble, install or operate
the product. Contact customer service for replacement part.
●
Estimated Assembly Time : 20 30 minutes
●
Tools Required for Assembly (not included) : Flathead Screwdriver Phillips Screwdriver, Pliers,
Electrical Tape, Wire Cutters, Safety Glasses &1,100 Watt, Type A Medium Base Bulb.
●
Helpful Tools (not included) : Wire Strippers.
,
-
1 OF 3
INSTALLATION INSTRUCTIONS
STEP 1:
.a Determine the Rods to be assembled according to your
desired hanging height.
b. Pass the Supply Wires with Ground Wire through the
chosen Rods and then thread Rods and Socket Assembly
together as shown. Tighten until snug.
STYLE NUMBER GE1507SE:
6” Rod
6” Rod
12” Rod
12” Rod
Supply Wires with
Ground Wire
Socket Assembly
STEP 2:
.
a Pass the Supply Wires with Ground Wire through the
Swivel and Ceiling Canopy.
.
b Thread the Swivel onto the top end ofthe Upper Rod and
hand tighten until snug.
STEP 3:
a Screw the Mounting Screws into the Crossbar place the
. ,
Lock Washers over the Mounting Screws and thread the
Hex Nuts onto the Mounting Screws as shown Secure
.
the position of the Mounting Screws by tightening the Hex
Nuts against the Crossbar
b Secure the Crossbar to the Outlet Box with Outlet Box
.
Screws
.
.
STEP 4:
* ( ) .
Use Wire Connectors not supplied to connectthe wires
.
a Connectthe House Ground Wire to the Fixture Ground
Wire.
.
b Connectthe House White Wire to the Fixture Supply Wire
( )
White or Ribbed Side .
. ( )
c Connect the House Black or Red Wire to the Fixture
Supply Wire Black or Smooth Side
.
d Wrap each connection with approved electrical tape and
carefully stuff all of the connected wires into the Outlet
.
Box
( ) .
Outlet Box
WHITE WIRE
FROM HOUSE
BLACK OR RED WIRE( )
FROM HOUSE
GROUND WIRE
FROM HOUSE
Ceiling Canopy
Swivel
Supply Wire with
Ground Wire
Upper Rod
Mounting Screw
Crossbar
Hex Nut
Lock Washer
Outlet Box Screw
WHITE OR RIBBED
FROM FIXTURE
BLACKORSMOOTH
FROM FIXTURE
GROUND WIRE
FROM FIXTURE
2 OF 3
Loading...