Page 1
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
. .
, .
INSTRUCTION SHEET IS ER1814STYLE NUMBER ER1814IS ER1814PN: ,
PACKAGE CONTENTS
Part
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
Hex Nut (for Mounting Screw)
Description
Crossbar
Green Ground Screw
Mounting Screw
Lock Washer
Mounting Ball
Steel Collar
Socket Collar with Harp
Large Flat Washer
Rubber Washer
Small Flat Washer
Hex Nut (1/8IP)
Finial
Ceiling Canopy
6 Rod"
12 Rod"
Socket Assembly
Socket Upper Collar
Shade
Diffuser
Quantity
1pc
1pc
2pcs
2pcs
2pcs
2pcs
1pc
1pc
1pc
1pc
1pc
1pc
1pc
1pc
2pcs
2pcs
1pc
1pc
1pc
1pc
ISSUED 07-2008 Revised 2008 11-10-
N
A
B
C
D
E
F
G
H
I
O
P
Q
R
!
WARNINGS AND CAUTIONS
WARNING:
● Befo re beginning the in stal la tion, tu rn off el ectricity at th e circuit breaker box or the ma in fuse box by
switching off the circuit breaker or removing the fuse.
CAUTIONS:
● These instructions are provided for your safe ty. It is very i mportant t hat they are read completely before
the installation of your fixture. We are strongly recommend that a professional electrician install the fixture.
● Di sconnect fixture from t he power source before replacing t he bulb(s), ma king sure the bulb(s) had
sufficient time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may
result.
PREPARATION
● Befo re beginning in st allation of prod uct, make sure a ll parts are present. Comp ar e parts with p ac kage
contents list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or
operate the product. Contact customer service for replacement part.
● Estimated Assembly Time : 10 20 minutes
● Tools R equi red for Assembly (not included): Flath ea d s crew driver Phillips scr ewdriver, plier s, electrical
tape, wire cutters, safety glasses &1, 100 Watts, Type A Medium Base Bulbs.
● He lp ful Tools (not included): Wire Strippers.
J
K
L
M
,
-
S
T
1 OF 4
Page 2
INSTALLATION INSTRUCTIONS
STEP 1:
a Determine the Rods to be assembled according to your
.
desired hanging height.
b Pass the Supply Wires with Ground Wire through the
.
chosen Rods and then thread Rods and SocketAssembly
together as shown. Tighten until snug.
STYLE NUMBER ER1814IS ER1814PN: ,
6” Rod
6” Rod
12” Rod
12” Rod
Supply Wires with
Ground Wire
STEP 2:
a Pass the Supply Wires with Ground Wire through the
.
Swivel and Ceiling Canopy.
b Thread the Swivel onto the top end of the Upper Rod and
.
hand tighten until snug.
STEP 3:
a Screw the Mounting Screws into the Crossbar place the
. ,
Lock Washers over the Mounting Screws and thread the
Hex Nuts onto the Mounting Screws as shown Secure the
position of the Mounting Screws by tightening the Hex Nuts
against the Crossbar
b Secure the Crossbar to the Outlet Box with Outlet Box
.
Screws
.
.
.
Socket Assembly
Ceiling
Canopy
Swivel
Supply Wire with
Ground Wire
Upper Rod
Mounting Screw
Crossbar
Hex Nut
Lock Washer
2 OF 4
Outlet Box
Outlet Box Screw
Page 3
INSTALLATION INSTRUCTIONS
STEP 4:
* ( )
Use Wire Connectors not supplied to connect the
.
wires
.
a Connect the House Ground Wire to the Fixture Ground
Wire.
. ( )
b Connect the House White or Ribbed Wire to the
Fixture Supply Wire White or Ribbed Side .
. ( )
c Connect the House Black or Red Wire to the Fixture
Supply Wire Black or Smooth Side
.
d Wrap each connection with approved electrical tape and
( ).
( )
carefully stuff all of the connected wires into the Outlet
.
Box
STEP 5:
a Place the Ceiling Canopy over the Mounting Screws and
.
thread Mounting Balls onto the Mounting Screws to secure
it. Hand tighten until snug.
STYLE NUMBER ER1814IS ER1814PN: ,
WHITE OR RIBBED
FROM HOUSE
BLACK OR RED WIRE( )
FROM HOUSE
GROUND WIRE GROUND WIRE
FROM HOUSE FROM FIXTURE
WHITE OR RIBBED
FROM FIXTURE
BLACK OR SMOOTH
FROM FIXTURE
Outlet Box
Mounting Screw
Mounting Ball
Ceiling
Canopy
STEP 6:
a Place the Socket Upper Collar the Shade and the Steel
. ,
Collar over the Socket as shown. Thread the Socket
Collar with Harp onto the Socket and hand tighten until
snug to secure them
.
Socket
Socket Upper Collar
Shade
Steel Collar
Socket Collar
with Harp
STEP 7:
a Install correct Bulb referring to fixture markings and/or labels for maximum wattage..
3 OF 4
Page 4
INSTALLATION INSTRUCTIONS
STEP 8:
a Thread the Hex Nut (1/8IP) onto the nipple on the bottom
.
end of the Harp and adjust to proper location for rest
components.
b. Place Big Flat Washer, Rubber Washer, Diffuser and Small
Flat Washer over the end of the Harp as shown. Secure
them by threading the Finial onto the nipple on the bottom
end of the Harp. Hand tighten until snug.
STYLE NUMBER ER1814IS ER1814PN: ,
Harp
Hex Nut (1/8IP)
Big Flat Washer
Rubber Washer
Diffuser
Finial
Small Flat Washer
Your installation is completed now. Restore electricity. Retain this sheet for future reference.
4 OF 4
Loading...