Quoizel DX1718C User Manual
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
. .
, .
INSTRUCTION SHEET IS DX1718-
STYLE NUMBER DX1718C:
PACKAGE CONTENTS
Part
A
B
C
D
E
F
G
H
I
J
K
L
M
N
Lock Washer (for #8-32 Screw)
Description
Crossbar
Green Ground Screw
Mounting Screw
Hex Nut (for #8-32 Screw)
Mounting Ball
Hex Nut (1/8IP)
Stem
Lock Ball
Rubber Washer
Finial
Fixture Assembly
Shade
Glass Panel
Quantity
1pc
1pc
2pcs
2pcs
2pcs
2pcs
1pc
1pc
4pcs
2pcs
1pc
1pc
1pc
1pc
Revised 2008-11-05
A
B
C
D
E
F
G
H
I
J
K
L
M
!
WARNINGS AND CAUTIONS
WARNING:
● Befo re beginning the in stal la tion, tu rn off el ectricity at th e circuit breaker box or the ma in fuse box by
switching off the circuit breaker or removing the fuse.
CAUTIONS:
● These instructions are provided for your safe ty. It is very i mportant t hat they a re read completely before
the installation of your fixture. We strongly recommend that a professional electrician install the fixture.
● Di sconnect fixture from t he power source before replacing t he bulb( s), ma king sure t he bulb(s) had
sufficient time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may
result.
PREPARATION
● Befo re beginning in st allation of prod uct, make sure a ll parts are present. Comp ar e parts with p ac kage
contents list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or
operate the product. Contact customer service for replacement part.
● Estimated Assembly Time : 30 45 minutes
● Tools R equi red for Assembly (not included): F lath ea d screwdriver Phillips screwdriver, pliers, electrical
tape, wire cutters, safety glasses &3, 60 Watt, Type A Medium Base Bulbs.
● He lp ful Tools (not included): Wire Strippers.
N
,
-
1 OF 3
INSTALLATION INSTRUCTIONS
STYLE NUMBER DX1718C:
STEP 1:
a Screw the Mounting Screws into the Crossbar place the
. ,
Lock Washers over the Mounting Screws and thread the
Hex Nuts onto the Mounting Screws as shown Secure the
.
position of the Mounting Screws by tightening the Hex
Nuts against the Crossbar
b Secure the Crossbar to the Outlet Box with Outlet Box
.
Screws
.
.
STEP 2 :
. - .a Refer to Step 3 Wire Connections to connect wires
b. Place Fixture Canopy onto Outlet Box aligning 2 holes in
the Backplate with 2 Mounting screws threaded on the
Crossbar and secure it against wall with Mounting Balls
Mounting Screw
Outlet Box
.
Crossbar
Hex Nut
Lock Washer
Outlet Box Screw
Crossbar
Mounting Screw
Fixture Canopy
Mounting Ball
STEP 3:
* ( )
Use Wire Connectors not supplied to connect the
.
wires
.
a Connect the House Ground Wire to the Fixture Ground
Wire.
. ( )
b Connect the House White or Ribbed Wire to the
Fixture Supply Wire White or Ribbed Side .
. ( )
c Connect the House Black or Red Wire to the Fixture
Supply Wire Black or Smooth Side
.
d Wrap each connection with approved electrical tape and
( ).
( )
carefully stuff all of the connected wires into the Outlet
.
Box
STEP 4:
a Thread the short nipple end of the Stem into the Coupling
.
underside of the Socket Assembly. Hand tighten until
snug.
WHITE OR RIBBED
FROM HOUSE
BLACK OR RED WIRE( )
FROM HOUSE
GROUND WIRE GROUND WIRE
FROM HOUSE FROM FIXTURE
WHITE OR RIBBED
FROM FIXTURE
BLACK OR SMOOTH
FROM FIXTURE
Coupling
Stem
Socket
Assembly
2 OF 3
Loading...