
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
INSTRUCTION SHEET IS DW1824STYLE NUMBER DW1824C:
PACKAGE CONTENTS
Part
A
Crossbar
Green Ground Screw
B
Lock Washer
C
Hex Nut
D
Nipple
E
Ceiling Canopy
F
Canopy Lock Ring
G
Ceiling Canopy Loop
H
Fixture Chain
I
Stem
J
K
Crystal Cylinder
L
Metal Cylinder
M
Cap
Shade with Sockets
N
Fixture Loop
O
Center Column
P
Q
Diffuser
Finial with Nipple
R
S
Rubber Washer
T
Flat Washer
Description
Quantity
1pc
1pc
2pcs
3pcs
1pc
1pc
1pc
1pc
1pc
1pc
1pc
1pc
1pc
1pc
1pc
1pc
1pc
1pc
1pc
1pc
ISSUED 04-2009 Revised 2009-11-13
A
B
C
D
E
F
G
H
I
J
K
L
M
O
P
Q
R
S
T
!
WARNINGS AND CAUTIONS
WARNING:
●
Before beginning the installation, turn off electricity at the circuit breaker box or the main fuse box by
switching off the circuit breaker or removing the fuse.
CAUTION:
●
These instructions are provided for your safety. It is very important that they are read completely before
the installation of your fixture. We strongly recommend that a professional electrician install the fixture.
●
Disconnect fixture from the power source before replacing the bulb(s), making sure the bulb(s) had
sufficient time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may
result.
PREPARATION
Before beginning installation of product, make sure all parts are present. Compare parts with package
●
contents list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or
operate the product. Contact customer service for replacement part.
●
Estimated Assembly Time : 30 45 minutes
●
Tools Required for Assembly (not included) : Flathead Screwdriver Phillips Screwdriver, Pliers,
Electrical Tape, Wire Cutters, Safety Glasses &4, 75 Watt, Type - A Medium Base Bulbs.
●
Helpful Tools (not included) : Wire Strippers.
N
,
1of4

INSTALLATION INSTRUCTIONS
STEP 1 :
.
a Thread the Nipple on the bottom center of the Center
Column into the Hex Coupling on the top center of the
Shade with Sockets. Hand tighten until snug.
b Thread the Fixture Loop onto the nipple on the top center
.
of the Center Column and tighten until snug.
STYLE NUMBER DW1824C:
Fixture Loop
Center Column
STEP 2 :
a Thread the beaded end of the Stem into the Coupling on
.
the bottom center of the Socket Assembly. Hand tighten
until snug.
b Locate the Diffuser, the Rubber Washer and the Flat
.
Washer over the end of the Stem and secure with the Hex
Nut. Hand tighten until snug.
Shade with Sockets
Shade with Sockets
Diffuser
Nipple
Hex Coupling
Coupling
Stem
STEP 3 :
a Pass the Cap, the Crystal Cylinder and the Metal Cylinder
.
over the end of the Stem. Secure them by threading the
Finial with Nipple into the Stem. Hand tighten until snug.
2of4
Flat Washer
Cap
Metal Cylinder
Rubber Washer
Hex Nut
Stem
Crystal Cylinder
Finial with Nipple

INSTALLATION INSTRUCTIONS
STEP 4:
a Secure the Crossbar onto the Outlet Box with Outlet
.
Box Screws Tighten until snug
..
STEP 5:
*.
Pliers is required on this step
..
a Thread one Hex Nut onto top end of the Nipple
.
b Place one Lock Washer over the top end of the Nipple
and then thread the Nipple into the center lock hole of
the Crossbar
.,
c Using pliers thread the Hex Nut against the Crossbar
and hand tighten until snug
.
d Thread another Hex Nut onto the bottom end of the
Nipple
.
.
.
Crossbar
STYLE NUMBER DW1824C:
Outlet Box
Crossbar
Outlet Box
Screw
Lock Washer
Hex Nut
Nipple
Hex Nut
STEP 6:
a Adjust the Fixture Chain to your desired length by
.
removing the links if needed
Please note that depends on chain material thickness
*,
you might be required to use chain pliers to spread
links open
b Pull the supply wires through the Fixture Chain
.
alternating links And then pull the wires through the
.
.
following components in turn
Canopy Lock Ring Ceiling Canopy Canopy Chain
Loop Lock Washer and Nipple
,,.
c Place Lock Washer over the end of the Nipple and
.
,,
thread the Canopy Chain Loop onto the end of the
Nipple
d Use plier thread the Hex Nut against the Canopy
.,
.
Chain Loop and tighten until snug
e Attach one end of the Fixture Chain onto the Fixture
.
Loop and attach the another end of the chain onto the
Canopy Chain Loop
f Refer to Step Wire Connections to connect wires
.- .
g Push the Ceiling Canopy upward over the Outlet Box
..
h Thread the Canopy Lock Ring onto the Canopy Chain
.
.
7
Loop and tighten until snug to secure the Ceiling
Canopy
.
.
Nipple
Hex Nut
Lock Washer
Canopy Chain Loop
:
Ceiling Canopy
.
Fixture Chain
Canopy Lock Ring
Fixture Loop
3of4

INSTALLATION INSTRUCTIONS
STEP 7:
*()
Use Wire Connectors not supplied to connect the
.
wires
.
a Connect the House Ground Wire to the Fixture Ground
Wire.
.()
b Connect the House White or Ribbed Wire to the
Fixture Supply Wire White or Ribbed Side .
.()
c Connect the House Black or Red Wire to the Fixture
Supply Wire Black or Smooth Side
.
d Wrap each connection with approved electrical tape
().
()
and carefully stuff all of the connected wires into the
Outlet Box
.
STEP 8:
a Install the correct Bulbs referring to fixture markings and or labels for maximum wattage
./.
STYLE NUMBER DW1824C:
WHITE OR RIBBED
FROM HOUSE
BLACK OR RED WIRE()
FROM HOUSE
GROUND WIRE GROUND WIRE
FROM HOUSE FROM FIXTURE
WHITE OR RIBBED
FROM FIXTURE
BLACK OR SMOOTH
FROM FIXTURE
Your installation is completed now Restore Retain this sheet for future reference
.. .
electricity
4of4