Quoizel DW1717C User Manual
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
INSTRUCTION SHEET IS DW1717:STYLE NUMBER DW1717C:
PACKAGE CONTENTS
Part
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
Crossbar
Green Ground Screw
Mounting Screws
Lock Washer
Hex Nut for Mounting Screw()
Mounting Ball
Stem
Crystal Cylinder
Metal Cylinder
Cap
Hex Nut (1/8 IP)
Ceiling Canopy Assembly
Shade with Sockets
Diffuser
Finial with Nipple
Rubber Washer
Flat Washer
Description
Quantity
1pc
1pc
2pcs
2pcs
2pcs
2pcs
1pc
1pc
1pc
1pc
1pc
1pc
1pc
1pc
1pc
1pc
1pc
ISSUED 04-2009 Revised 2009-11-13
A
B
C
D
E
F
G
H
I
J
K
O
P
Q
L
M
N
!
WARNINGS AND CAUTIONS
WARNING:
●
Before beginning the installation, turn off electricity at the circuit breaker box or the main fuse box by
switching off the circuit breaker or removing the fuse.
CAUTION:
●
These instructions are provided for your safety. It is very important that they are read completely before
the installation of your fixture. We strongly recommend that a professional electrician install the fixture.
●
Disconnect fixture from the power source before replacing the bulb(s), making sure the bulb(s) had
sufficient time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may
result.
PREPARATION
Before beginning installation of product, make sure all parts are present. Compare parts with package
●
contents list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or
operate the product. Contact customer service for replacement part.
●
Estimated Assembly Time : 30 45 minutes
●
Tools Required for Assembly (not included) : Flathead Screwdriver Phillips Screwdriver, Pliers,
Electrical Tape, Wire Cutters, Safety Glasses &3, 60 Watt, Type - A Medium Base Bulbs.
●
Helpful Tools (not included) : Wire Strippers.
,
1OF3
INSTALLATION INSTRUCTIONS
STEP 1:
a Thread the nipple in the end of the Ceiling Canopy
.
Assembly onto the Hex Coupling on the top center of the
Shade with Sockets. Hand tighten until snug.
STYLE NUMBER DW1717C:
Ceiling Canopy
Assembly
Coupling
STEP 2:
a Screw the Mounting Screws into the Crossbar place the
.,
Mounting Screw
Shade with Sockets
Crossbar
Lock Washers over the Mounting Screws and thread the
Hex Nuts onto the Mounting Screws as shown Secure the
.
position of the Mounting Screws by tightening the Hex Nuts
against the Crossbar
b Secure the Crossbar to the Outlet Box with Outlet Box
.
Screws
.
.
Outlet Box
Outlet Box Screw
STEP 3:
*()
Use Wire Connectors not supplied to connect the
.
wires
.
a Connect the House Ground Wire to the Fixture Ground
Wire.
.()
b Connect the House White or Ribbed Wire to the
Fixture Supply Wire White or Ribbed Side .
.()
c Connect the House Black or Red Wire to the Fixture
Supply Wire Black or Smooth Side
.
d Wrap each connection with approved electrical tape and
().
()
carefully stuff all of the connected wires into the Outlet Box
WHITE OR RIBBED
FROM HOUSE
BLACK OR RED WIRE()
FROM HOUSE
GROUND WIRE GROUND WIRE
.
FROM HOUSE FROM FIXTURE
WHITE OR RIBBED
FROM FIXTURE
BLACK OR SMOOTH
FROM FIXTURE
Hex Nut
Lock Washer
STEP 4 :
a Place the Ceiling Canopy onto Outlet Box aligning 2
.
holes in the Ceiling Canopy with 2 Mounting screws
threaded on the Crossbar and secure it against wall
with Mounting Balls
.
2OF3
Outlet Box
Mounting Screw
Ceiling Canopy
Mounting Ball
Loading...