Page 1
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
. .
, .
INSTRUCTION SHEET IS DH5103STYLE NUMBER DH5103AN,DH5103PN:
PACKAGE CONTENTS
Part
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
Description
Crossbar
Green Ground Screw
Lock Washer
Hex Nut
Nipple (for mounting kits)
Ceiling Canopy
Canopy Lock Ring
Ceiling Canopy Loop
Fixture Chain
Lock Ball
Lock Screw
Socket Collar
SocketAssembly
Fixture Loop
Shade
Side Arm
CenterColumn Assembly
Quantity
1pc
1pc
2pcs
3pcs
1pc
1pc
1pc
1pc
1pc
3pcs
3pcs
3pcs
1pc
1pc
3pcs
3pcs
1pc
ISSUED 09-2008
N
A
O
B
C
D
E
F
G
H
I
J
Q
P
!
WARNINGS AND CAUTIONS
WARNING:
● Before beginning the installation, turn off electric ity at the circuit breaker bo x o r the main fuse box by
switching off the circuit breaker or removing the fuse.
CAUTIONS:
● These instructions are pro vide d for your safety. It is very important that th ey are read complete ly be fore
the installation of your fixture. We strongly recommend that a professional electrician install the fixture.
● Disconnect fixture from the power source before replacing the bulb(s ), maki ng sure the bulb(s) had
sufficient time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may
PREPARATION
K
L
M
Before beginning installation of product, make sure all parts are present. Compare parts with package
●
contents list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or
operate the product. Contact customer service forreplacement part.
● Estim ated A ss embly Time: 15 30 m inut es
● Too ls Re quired for Assembly(not in clud ed): Flathead Screwdrive r Phillips Scre wdri ver, Pliers,
Electrical Tape, Wire Cutters, Safety Glasses & 3,100 Watt, Type - A Medium Base Bulbs.
● Helpful Tools(not included): Wire Stri pper s.
-
,
,
1 OF 4
Page 2
INSTALLATION INSTRUCTIONS
STEP 1 :
a Unfold Support Arms at120 degree locations.
.
b. Thread the Center Column Assembly onto the Hex
Coupling on the top center of the Socket Assembly as
shown. Please make sure the Bolts on the side of the
Center Column line up Mounting Holes on the Support
Arms before tighten them together.
CenterColumn
Assembly
STYLE NUMBER DH5103AN,DH5103PN:
Bolt
Support Arm
STEP 2 :
a Locate Side Arms. Place the holes on the small scroll
.
ends of Side Arms over Bolts on the side of the Center
Column Assembly, and line up the holes on the big scroll
ends onto the Mounting Holes on the SupportArms.
b. Thread Lock Balls onto Bolts and thread Lock Screws into
Mounting Holes to secure Side Arms. Hand tighten until
snug.
Hex Coupling
Center
Column
Assembly
Support Arm
Bolt
Mounting Hole
Socket
Assembly
Lock Ball
Side Arm
Lock Screw
Mounting
Hole
STEP 3 :
a Thread the Fixture Loop onto the nipple in the center of
.
the Fixture Canopy.Hand tighten until snug.
STEP 4:
a Secure the Crossbar onto the Outlet Box with Outlet
.
Box Screws Tighten until snug
. .
Outlet Box
Fixture Loop
Fixture Canopy
Crossbar
Outlet Box
Screw
2 OF 4
Page 3
INSTALLATION INSTRUCTIONS
STEP 5:
* .
Plier is required on this step
. .
a Thread one Hex Nut onto top end of the Nipple
.
b Place one Lock Washer over the top end of the Nipple
and then thread the Nipple into the center lock hole of
the Crossbar
. ,
c Using plier thread the Hex Nut against the Crossbar
.
and hand tighten until snug
.
d Thread another Hex Nut onto the bottom end of the
Nipple
.
STEP 6:
a Adjust the Fixture Chain to your desired length by
.
removing the links if needed
Please note that depends on chain material
*
thickness you might be required to use chain pliers to
spread links open
b Pull the supply wires through the Fixture Chain
.
alternating links And then pull the wires through the
following components in turn
Canopy Lock Ring Ceiling Canopy Canopy Chain
Loop Lock Washer and Nipple
c Place Lock Washer over the end of the Nipple and
.
thread the Canopy Chain Loop onto the end of the
Nipple
d Use plier thread the Hex Nut against the Canopy
. ,
Chain Loop and tighten until snug
e Attach one end of the Fixture Chain onto the Fixture
.
Loop and attach the another end of the chain onto the
Canopy Chain Loop
f Refer to Step 7 Wire Connections to connect wires
. - .
g Push the Ceiling Canopy upward over the Outlet Box
. .
h Thread the Canopy Lock Ring onto the Canopy Chain
.
Loop and tighten until snug to secure the Ceiling
Canopy
,
.
.
, ,
, , .
.
.
.
STYLE NUMBER DH5103AN,DH5103PN:
Lock Washer
Crossbar
Hex Nut
.
Nipple
(for mounting kits)
Hex Nut
.
Nipple
Hex Nut
Lock Washer
Canopy Chain Loop
:
Ceiling Canopy
.
Fixture Chain
Canopy Lock Ring
Fixture Loop
STEP 7:
* ( )
Use Wire Connectors not supplied to connect the
.
wires
.
a Connect the House Ground Wire to the Fixture Ground
Wire.
. ( )
b Connect the House White or Ribbed Wire to the
Fixture Supply Wire White or Ribbed Side .
. ( )
c Connect the House Black or Red Wire to the Fixture
Supply Wire Black or Smooth Side
.
d Wrap each connection with approved electrical tape
( ) .
and carefully stuff all of the connected wires into the
Outlet Box
.
( )
3 OF 4
WHITE OR RIBBED
FROM HOUSE
BLACK OR RED WIRE( )
FROM HOUSE
GROUND WIRE GROUND WIRE
FROM HOUSE FROM FIXTURE
WHITE OR RIBBED
FROM FIXTURE
BLACK OR SMOOTH
FROM FIXTURE
Page 4
INSTALLATION INSTRUCTIONS
STEP 8:
a Position the Shade over the Socket as shown. Secure the
.
Shade by threading the Socket Collar onto the Socket.
Hand tighten until snug.
STEP 9:
a Install correct Bulbs referring to fixture markings and or labels for maximum wattage
. / .
STYLE NUMBER DH5103AN,DH5103PN:
Socket
Shade
SocketCollar
Your installation is completed now Restore Retain this sheet for future reference
. . .
electricity
4OF 4
Loading...