Page 1
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
INSTRUCTION SHEET IS DH5009:STYLE NUMBER DH5009AN, DH5009PN:
PACKAGE CONTENTS
Part
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
Crossbar
Green Ground Screw
Lock Washer
Hex Nut
Nipple
Ceiling Canopy
Canopy Lock Ring
Ceiling Canopy Loop
Fixture Chain
Lock Ball
Fixture Loop
Round Plate
Knurled Nut
Center Stem with Spacer and Fixture Cover
Socket Collar Tool
Side Arm
Shade
Socket Collar
Socket Assembly
Description
Quantity
1pc
1pc
2pcs
2pcs
1pc
1pc
1pc
1pc
1pc
6pcs
1pc
1pc
1pc
1pc
1pc
3pcs
9pcs
9pcs
1pc
Revised 2009-12-31
A
B
C
D
E
F
G
H
I
J
K
L
M
O
N
P
Q
R
!
WARNINGS AND CAUTIONS
WARNING:
●
Before beginning the installation, turn off electricity at the circuit breaker box or the main fuse box by
switching off the circuit breaker or removing the fuse.
CAUTION:
●
These instructions are provided for your safety. It is very important that they are read completely before
the installation of your fixture. We strongly recommend that a professional electrician install the fixture.
●
Disconnect fixture from the power source before replacing the bulb(s), making sure the bulb(s) had
sufficient time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may
result.
PREPARATION
Before beginning installation of product, make sure all parts are present. Compare parts with package
●
contents list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or
operate the product. Contact customer service for replacement part.
●
Estimated Assembly Time : 30 45 minutes
●
Tools Required for Assembly (not included) : Flathead Screwdriver Phillips Screwdriver, Pliers,
Electrical Tape, Wire Cutters, Safety Glasses & 9, 100 Watt, Type - A Medium Base Bulbs.
●
Helpful Tools (not included) : Wire Strippers.
S
,
1OF5
Page 2
INSTALLATION INSTRUCTIONS
STEP 1:
a. Unfold Support Arms to proper location refer to the Socket
Orientation.
STYLE NUMBER DH5009AN, DH5009PN:
Support
Arm
Support Arm
Socket Orientation
STEP 2:
a. Screw the end of the Center Stem into the Coupling on the
top center of the Socket Assembly.
b. Line up the Bolts on the Spacer and the Support Arms on the
bottom tier of the Socket Assembly. Secure them with the
Hex Coupling inside the Fixture Cover. Tighten until snug.
c. Adjust the Hex Nut on the top end of the Center Stem to
proper location for the Round Plate, Knurled Nut and
Fixture Loop in the next step.
STEP 3:
a. Place the Round Plate over the top end of the Center Stem
and secure with Knurled Nut. Hand tighten until snug.
b. Thread the Fixture Loop onto the top center of the fixture
and hand tighten until snug.
Fixture Cover
Coupling
Socket
Assembly
Support Arm
Hex Nut
Hex Coupling
Bolt
Spacer
Center Stem
Fixture Loop
Knurled Nut
Round Plate
Center Stem
2OF5
Page 3
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS
STYLE NUMBER DH5009AN, DH5009PN:
STEP 4
:
a. Pass the holes on the Side Arm over the Bolts on the Spacer
and Support Arm (bottom tier). Secure with the Lock Balls
and hand tighten until snug.
Lock Ball
Bolt
Spacer
Side Arm
Lock Ball
Bolt
Support Arm
STEP 5:
a Secure the Crossbar onto the Outlet Box with Outlet Box
.
Screws Tighten until snug
..
Outlet Box
Crossbar
Outlet Box
Screw
STEP 6:
*.
Pliers is required on this step
..
a Thread one Hex Nut onto top end of the Nipple
.
b Place one Lock Washer over the top end of the Nipple
and then thread the Nipple into the center lock hole of
the Crossbar
.,
c Using pliers thread the Hex Nut against the Crossbar
and hand tighten until snug
.
d Thread another Hex Nut onto the bottom end of the
Nipple
.
.
.
Crossbar
Lock Washer
Hex Nut
Nipple
3OF5
Hex Nut
Page 4
INSTALLATION INSTRUCTIONS
STEP 7:
a Adjust the Fixture Chain to your desired length by
.
removing the links if needed
Please note that depends on chain material
*
thickness you might be required to use chain pliers to
spread links open
b Pull the supply wires through the Fixture Chain
.
alternating links And then pull the wires through the
following components in turn
Canopy Lock Ring Ceiling Canopy Canopy Chain
Loop Lock Washer and Nipple
c Place Lock Washer over the end of the Nipple and
.
thread the Canopy Chain Loop onto the end of the
Nipple
d Using pliers thread the Hex Nut against the Canopy
.,
Chain Loop and tighten until snug
e Attach one end of the Fixture Chain onto the Fixture
.
Loop and attach the another end of the chain onto the
Canopy Chain Loop
f Refer to Step 8 Wire Connections to connect wires
.- .
g Push the Ceiling Canopy upward over the Outlet Box
..
h Thread the Canopy Lock Ring onto the Canopy Chain
.
Loop and tighten until snug to secure the Ceiling
Canopy
,
.
.
,,
,,.
.
.
.
STYLE NUMBER DH5009AN, DH5009PN:
.
Nipple
Hex Nut
:
.
Lock Washer
Canopy Chain Loop
Ceiling Canopy
Fixture Chain
Canopy Lock Ring
STEP 8:
*()
Use Wire Connectors not supplied to connect the
.
wires
.
a Connect the House Ground Wire to the Fixture Ground
Wire.
.()
b Connect the House White or Ribbed Wire to the
Fixture Supply Wire White or Ribbed Side .
.()
c Connect the House Black or Red Wire to the Fixture
Supply Wire Black or Smooth Side
.
d Wrap each connection with approved electrical tape
().
()
and carefully stuff all of the connected wires into the
Outlet Box
.
WHITE OR RIBBED
FROM HOUSE
BLACK OR RED WIRE()
FROM HOUSE
GROUND WIRE GROUND WIRE
FROM HOUSE FROM FIXTURE
Fixture Loop
WHITE OR RIBBED
FROM FIXTURE
BLACK OR SMOOTH
FROM FIXTURE
4OF5
Page 5
INSTALLATION INSTRUCTIONS
STEP 9:
.
a Locate the Shade over the Socket. Using the Socket
Collar Tool (supplied), thread the Socket Collar onto the
Socket to secure the Shade. Hand tighten until snug.
STYLE NUMBER DH5009AN, DH5009PN:
Socket Collar
Tool
Socket Collar
Shade
Socket
STEP 10:
a Install correct Bulbs referring to fixture markings and or labels for maximum wattage
./.
Your installation is completed now Restore electricity Retain this sheet for future reference
.. .
5OF5
Loading...