Page 1
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
. .
, .
INSTRUCTION SHEET IS DH2820STYLE NUMBER DH2820AN,DH2820PN:
PACKAGECONTENTS
Part
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
Crossbar
Green Ground Screw
Hex Nut
Nipple
Lock Washer
Canopy Chain Loop
Canopy Lock Ring
Fixture Chain
Ceiling Canopy
Lock Ball
Shade Stop
Shade Holder
Cap
Fixture Loop
Stem Assembly
Side Arm
Tube
Center Stem with Fixture Canopy
Shade
Socket Assembly
Finial
Description
Quantity
1pc
1pc
4pcs
1pc
2pcs
1pc
1pc
1pc
1pc
6pcs
1pc
1pc
1pc
1pc
1pc
3pcs
1pc
1pc
1pc
1pc
1pc
Revised 2008-12 26-
A
B
C
D
E
F
G
H
I
J
N
O
P
Q
R
S
!
WARNINGSANDCAUTIONS
K
L
M
T
U
WARNING:
● Before beg inni ng t he i nsta llat ion, turn off electric ity at the circuit breaker b ox or the main fus e box by
switching off the circuit breaker or removing the fuse.
CAUTIONS:
● These instruc tions are provid ed for your safety. It is very important that th ey are read completely before the
installation of your fixture. We strongly recommend that a professional electrician install the fixture.
● Disc onnect fix ture from the power source before replacin g the bu lb(s), maki ng sure th e bulb(s) had su fficient
time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may result.
PREPARATION
● Before beg inni ng i nstallation of p roduct, make sure al l parts are present. Com pare parts w ith package
contents list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or
operate the product. Contact customer service for replacement part.
● Estimate d Assemb ly Time: 30 45 m inutes
● Tools Req uired for Assembly (not incl uded ): Flathead screwdriver Phi llips scre wd rive r, pliers, electrical
tape, wire cutters, safety glasses &4, 100 Watt, Type A Medium Base Bulb.
● Helpfu l Too ls (no t included): Wire Str ippe rs.
,
-
1 OF 4
Page 2
INSTALLATION INSTRUCTIONS
STEP 1 :
a.
Carefully unfold all Support Arms to proper locations
.
b Locate the Tube over the Center Stem with the Studs end
on the top Thread the end of the Center Stem into the Hex
Coupling on the center of the Socket Assembly Hand
tighten until snug Please adjust the Tube to make sure
Studs on the Tube and Support Arms are lined up before
tighten
.
.
.
.
STYLE NUMBER DH2820AN,DH2820PN:
.
Center Stem
STEP 2 :
a. Locate Side Arms and match the holes on them with Studs
on Center Stem and Support Arms Secure the Side Arms by
.
threading Lock Balls onto the Studs. Hand tighten until snug.
STEP 3 :
a Thread the Fixture Loop onto the Nipple on the top center of
.
the Fixture Canopy.Hand tighten until snug.
Tube
Support Arm
Stud
Tube
Stud
Hex Coupling
Socket
Assembly
Lock Ball
Side Arm
Lock Ball
Stud
Support Arm
Fixture Loop
STEP 4:
a. Secure the Crossbar onto the Outlet Box with Outlet Box
Screws Tighten until snug. .
Fixture Canopy
Crossbar
Outlet Box
Screw
Outlet Box
2 OF 4
Page 3
INSTALLATION INSTRUCTIONS
STEP 5:
*
Plier is required on this step
. .
Thread one Hex Nut onto top end of the Nipple
a
.
Place one Lock Washer over the top end of the Nipple and
b
.
then thread the Nipple into the center lock hole of the
Crossbar
. ,
Us plier thread the Hex Nut against the rossbar and
c ing c
hand tighten until snug
. .
Thread another Hex Nut onto the bottom end of the Nipple
d
.
.
STEP 6:
a Adjust the Fixture Chain to your desired length by removing
.
the links if needed
Please note that depends on chain material thickness you
* ,
might be required to use chain pliers to spread links open
b Pull the supply wires through the Fixture Chain alternating
.
links And then pull the wires through the following
.
components in turn
Canopy Lock Ring Ceiling Canopy Canopy Chain Loop,
Lock Washer and Nipple
c Place Lock Washer over the end of the Nipple and thread the
.
Canopy Chain Loop onto the end of the Nipple
d Using plier thread the Hex Nut against the Canopy Chain
. ,
Loop and tighten until snug
e Attach one end of the Fixture Chain onto the Fixture Loop and
.
attach the another end of the chain onto the Canopy Chain
Loop
.
f Refer to Step 7 Wire Connections to connect wires
. - .
g Push the Ceiling Canopy upward over the Outlet Box
. .
h Thread the Canopy Lock Ring onto the Canopy Chain Loop
.
and tighten until snug to secure the Ceiling Canopy
.
:
, ,
, .
.
.
.
STYLE NUMBER DH2820AN,DH2820PN:
Lock Washer
Crossbar
.
Nipple
Hex Nut
Nipple
Hex Nut
Hex Nut
Lock Washer
Canopy Chain Loop
Ceiling Canopy
Fixture Chain
STEP 7:
* ( ) .
Use Wire Connectors not supplied to connect the wires
.
a Connect the House Ground Wire to the Fixture Ground
Wire.
. ( )
b Connect the House White or Ribbed Wire to the Fixture
Supply Wire White or Ribbed Side .
. ( )
c Connect the House Black or Red Wire to the Fixture
Supply Wire Black or Smooth Side
.
d Wrap each connection with approved electrical tape and
carefully stuff all of the connected wires into the Outlet Box
( )
( ) .
BLACK OR RED WIRE( )
.
Canopy Lock Ring
Fixture Loop
WHITE OR RIBBED
FROM HOUSE
FROM HOUSE
GROUND WIRE GROUND WIRE
FROM HOUSE FROM FIXTURE
WHITE OR RIBBED
FROM FIXTURE
BLACK OR SMOOTH
FROM FIXTURE
3 OF 4
Page 4
INSTALLATION INSTRUCTIONS
STEP 8:
a Thread short nipple end of the Stem Assembly into the Hex
.
Coupling underside of Socket Assembly and hand tighten
until snug.
STEP 9:
a Thread the Hex Nut onto the end of the Center Assembly
.
and adjust to proper location for the rest components
b. Locate the Shade Stop Shade and Shade Holder over the
end ofthe Stem Assembly and secure with the Hex Nut
Hand tighten until snug
,
.
STYLE NUMBER DH2820AN,DH2820PN:
Socket
Assembly
Hex Coupling
Stem Assembly
.
.
Stem Assembly
STEP 10:
a Locate the Cap over the end of the Nipple and secure with the
.
Finial. Hand tighten until snug.
Hex Nut
Shade Stop
Shade
Shade Holder
Hex Nut
STEP 11:
a Install correct bulbs referring to fixture markings and or labels for maximum wattage. / .
. . .Your installation is completed now Restore electricity Retain this sheet for future reference
4 OF 4
Nipple
Cap
Finial
Loading...