Quoizel DH1722AN User Manual
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
. .
, .
PACKAGE CONTENTS
INSTRUCTION SHEET IS DH1718: STYLE NUMBER:DH1718PN DH1718AN,
DH1722PN DH1722AN,
ISSUED 09-2008
Part
A
B
C
D
E
F
G
H
I
J
K
L
M
N
!
Hex Nut for Mounting Screw( )
WARNINGS AND CAUTIONS
Description
Crossbar
Green Ground Screw
Mounting Screws
Lock Washer
Mounting Ball
Hex Nut(1/8 IP.)
Finial
StemAssembly
Flat Washer
Rubber Washer
Cap
FixtureAssembly
Shade
Quantity
1pc
1pc
2pcs
2pcs
2pcs
2pcs
1pc
1pc
1pc
2pcs
2pcs
1pc
1pc
1pc
WARNING:
Before beginning the installation, turn off electricity at the circuit breaker box or the main fuse box by
●
switching off the circuit breakeror removing the fuse.
A
B
C
D
E
F
G
H
I
J
K
L
M
N
CAUTION:
These instructions are provided for your safety. It is very important that they are read completely before the
●
installation of your fixture. We strongly recommend that a professional electrician install the fixture.
Disconnect fixture from the power source before replacing the bulb(s), making sure the bulb(s) had
●
sufficient time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may result.
PREPARATION
Before beginning installation of product, make sure all parts are present. Compare parts with package
●
contents list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or
operate the product. Contact customer service forreplacement part.
EstimatedAssembly Time : 15 30 minutes
●
Tools Required forAssembly (not included) : Flathead Screwdriver Phillips Screwdriver, Pliers,
●
Electrical Tape, Wire Cutters, Safety Glasses &3, 100 Watt, Type -AMedium Base Bulbs.
Helpful Tools (not included) : Wire Strippers.
●
INSTALLATION INSTRUCTIONS
STEP 1:
a Screw the Mounting Screws into the Crossbar place the
. ,
Lock Washers over the Mounting Screws and thread the
Hex Nuts onto the Mounting Screws as shown Secure the
position of the Mounting Screws by tightening the Hex Nuts
against the Crossbar
b Secure the Crossbarto the Outlet Box with Outlet Box
.
Screws
.
.
,
Mounting Screw
Crossbar
Hex Nut
.
Lock Washer
1 OF 2
Outlet Box
Outlet Box Screw
INSTALLATION INSTRUCTIONS
STEP 2:
* ( )
Use Wire Connectors not supplied to connect the
.
wires
.
a Connect the House Ground Wire to the Fixture Ground
Wire.
. ( )
b Connect the House White or Ribbed Wire to the
Fixture Supply Wire White or Ribbed Side .
. ( )
c Connect the House Black or Red Wire to the Fixture
Supply Wire Black or Smooth Side
.
d Wrap each connection with approved electrical tape and
( ) .
carefully stuff all of the connected wires into the Outlet Box
( )
STYLE NUMBER DH1718AN,DH1718PN,: DH1722AN,DH1722PN
WHITE OR RIBBED
FROM HOUSE
BLACK OR RED WIRE( )
FROM HOUSE
GROUND WIRE GROUND WIRE
.
FROM HOUSE FROM FIXTURE
WHITE OR RIBBED
FROM FIXTURE
BLACK OR SMOOTH
FROM FIXTURE
STEP 3 :
a Unfold Side Arms at 120 degree locations.
.
b. Place the Ceiling Canopy onto Outlet Box aligning 2
holes in the Ceiling Canopy with 2 Mounting screws
threaded on the Crossbar and secure it against wall with
Mounting Balls
.
STEP 4 :
a Thread the beaded end of the Stem Assembly into the
.
Coupling underside of the Socket Cluster. Hand tighten until
snug.
Mounting
Screw
Mounting
Ball
Coupling
Outlet
Box
Ceiling
Canopy
Side Arm
SocketCluster
Stem assembly
STEP 5 :
a Locate the following components over the end of the Stem
.
Assembly in turn:
Flat Washer, Rubber Washer, Shade, RubberWasher and
Flat Washer.
b. Thread the Hex Nut onto the end of the Stem Assembly to
secure the above parts. Tighten until snug.
c. Locate the Cap over the end of the Stem Assembly and
secure by threading the Finial onto the Stem. Hand tighten
until snug.
Rubber Washer
Rubber Washer
Hex Nut
Finial
STEP 6 :
a Install correct bulbs referring to fixture markings and or labels for maximum wattage. / .
. . .Your installation is completed now Restore electricity Retain this sheet for future reference
2 OF 2
Stem assembly
Flat Washer
Shade
Flat Washer
Cap
Loading...