Quoizel DH1616AN User Manual
INSTRUCTION SHEET IS DH1616-
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
. .
, .
PACKAGECONTENTS
Part
A
B
C
D
E
F
G
H
I
J
K
L
M
!
WARNINGSANDCAUTIONS
Description
Crossbar
Green Ground Screw
Lock Washer
Hex Nut
Nipple
Flat Washer
Rubber Washer
Hex Coupling
Ceiling Canopy
Stem with Hex Nut
Shade
Cap
Finial
Quantity
1pc
1pc
2pcs
3pcs
1pc
2pcs
1pc
1pc
1pc
1pc
1pc
1pc
1pc
STYLE NUMBER DH1616PN,DH1616AN:
ISSUED 07-2008 Revised 2008 08 28- -
A
B
C
D
E
F
G
H
I
J
K
L
M
WARNING:
● Before beginn ing the installation, turn off elect ricity at the circuit breaker bo x or the main f use box by
switching off the circuit breaker or removing the fuse.
CAUTIONS:
● These instructions are provided for your safet y. It is very important tha t they are rea d completely befo re the
installation of your fixture. We strongly recommend that a professional electrician install the fixture.
● Disconnect fi xture from the power sou rce bef ore replacing the bulb( s), making sure the b ulb(s) had suffi cient
time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may result.
PREPARATION
● Before beginn ing installation of product, make sure a ll parts are present. Compare p arts wi th package
contents list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or
operate the product. Contact customer service for replacement part.
● Est imated Assembly Time: 15 30 minutes
● Tool s Requi red for Assemb ly (not included): Flathead screwdriver Phill ips screwdriver, pliers, elect rical
tape, wire cutters, safety glasses &2, 60 Watt, Type A Medium Base Bulbs.
,
-
● Helpful Tools (not inclu ded): Wire Stripp ers.
ASSEMBLY
STEP 1:
a Locate the Crossbar and attach it to the Outlet Box
.
using the Outlet Box Screws not supplied
b Locate the Nipple and thread one Hex Nut onto it
.
( ).
about half way. Slip a Lock Washer onto it and thread
one end of the nipple into the center hole of the
Crossbar
c Position the Ceiling Canopy over the outlet box,
.
.
passing the mounting hole in the center of the Ceiling
Canopy over the end of Nipple
d Adjust the Nipple so approx 3 8 inch of the Nipple
.
.
. / "
is protruding from the mounting hole. This adjustment
may take a few tries.
e When this length is achieved, remove the Ceiling
.
Canopy and tighten the Hex Nut up against the
underside of the Crossbar with pliers.
Outlet Box Screw
Hex Nut
Nipple
Lock Washer
Ceiling Canopy
Outlet Box
Crossbar
1 OF 3
ASSEMBLYINSTRUCTIONS
STEP 2:
a. Thread another Hex Nut onto the other end of
the nipple. Thread this Hex Nut on just enough
so the inside surface of the pan rests against it.
You may have to trial fit the Ceiling Canopy
*
one more times to insure this distance also.
This Hex Nut is needed here to prevent you
from crushing down the center of the Ceiling
STEP 3:
* ( )
Use Wire Connectors not supplied to connect
the wires
.
a Connect the House Ground Wire to the Fixture
Ground Wire.
.
b Connect the House White Wire to the Fixture
Supply Wire White or Ribbed Side .
. ( )
c Connect the House Black or Red Wire to the
Fixture Supply Wire Black or Smooth Side
.
d Wrap each connection with approved electrical
tape and carefully stuff all of the connected wires
into the Outlet Box
.
( )
( ).
.
Ceiling Canopy
WHITE WIRE
FROM HOUSE
BLACK OR RED WIRE( )
FROM HOUSE
GROUND WIRE
FROM HOUSE
STYLE NUMBER DH1616AN,DH1616PN:
Nipple
Hex Nut
WHITE OR RIBBED
FROM FIXTURE
BLACK OR SMOOTH
FROM FIXTURE
GROUND WIRE
FROM FIXTURE
STEP 4:
a Position the Ceiling Canopy to the ceiling by.
passing the Nipple through the center hole
.
b Slip on the Flat Washer and the Lock Washer and
.
then thread the Hex Coupling to the bottom end of
the Nipple Snug down assembly until the Ceiling
Canopy is flush against the ceiling
*
Be sure that there are no trapped or pinched
.
.
wires along the edge of the pan.
STEP 5:
a Thread the beaded end of the Stem into the Hex
.
Coupling underside of the Ceiling Canopy. Hand
tighten until snug.
Nipple
Lock Washer
Stem with Hex Nut
Ceiling Canopy
Flat Washer
Hex Coupling
Ceiling
Canopy
Hex Coupling
STEP 6
.
a Install correct Bulbs referring to fixture markings and/or labels for maximum wattage.
:
2 OF 3
Loading...