Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing
the fixture. We strongly recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool
before removal. Do not subject glass parts to any shock while in operation or shattering may result.
A
G
Package Contents
Part
ACrossbar
B
C
D
E
F
G
H
I
J
K
Description
Mounting Screw
Lock Washer
Hex Nut
Mounting Ball
Fixture Body
Diffuser
Center Stem
Rubber Washer
Flat Washer
1/8 Hex Nut
FinialL
Quantity
1pc.
2 pcs.
2 pcs.
2 pcs.
2 pcs.
1pc.
1pc.
1pc.
1pc.
1pc.
1pc.
1pc.
H
B
C
D
E
F
I
J
K
L
Need assistance with partsor assembly? Call Quoizelcustomer service at 1-631-273-2700
2012 Quoizel Inc.
Thank you for purchasinga Quoizel product.
or visit us on-lineat www.quoizel.com
1of6
July2012
Page 2
CRA1717MC
FINISH: MOTTLED COCOA
1.5”
6.5” Dia.
GND
2.4mm
13Ga
QUOIZEL
R
12.5”
5.5”
17” Dia.
(3)100W
Medium Base Bulbs
(Not Supplied)
PART NUMBER
NO.
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2"
REPLACEMENT PART DESCRIPTION
2of6
REQ.
Page 3
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
Assembly Instruction Sheet #IS-CRA1717MC
For Style CRA1717MC
STEP 1 - Attach Mounting Screws, Lock
Washers and Hex Nuts to Crossbar
A. Line up a set of holes on the Crossbar (A) and Holes on
the Ceiling Canopy.
B. Thread Mounting Screws (B) into the holes on the
Crossbar (A), pass Lock Washers (C) and thread Hex Nut
(D) onto the Mounting Screws (B). Hand tighten until
snug.
STEP 2 - Attach Crossbar to Outlet Box
A. Attach the Crossbar (A) to Outlet Box and secure by
threading Outlet Box Screws (not supplied) into the
Mounting Holes on the Outlet Box. Tighten until snug.
Figure 1
Mounting Screw
Lock Washer
Ceiling
Canopy
Figure 2
Mounting
Hole
Crossbar
Hex Nut
Outlet
Box
Crossbar
Outlet Box
Screw
Need assistance with partsor assembly? Call Quoizelcustomer service at 1-631-273-2700
2012 Quoizel Inc.
Thank you for purchasinga Quoizel product.
or visit us on-lineat www.quoizel.com
3of6
July2012
Page 4
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
Assembly Instruction Sheet #IS-CRA1717MC
For Style CRA1717MC
STEP 3Make Wire Connections-
A. Use standard wire connectors to make all wire
connections. (Connectors are not included with fixture.)
Strip and prepare wire ends according to instructions
supplied with connectors.
B. Connect White Supply Wire from the Outlet Box to White
Wire from fixture.
C. Connect Black (or Red) Supply Wire from the Outlet Box
to Black Wire from fixture.
D. Connect Ground Wire from the Outlet Box to Ground
Wire from fixture.
E. Twist connectors until wires are tightly joined together.
F. Wrap each connection with approved electrical tape and
carefully stuff all the connected wires into the Outlet Box.
White wire from supplyWhite wire from fixture
Black wire from supply
(or Red)
Ground wire from supplyGround wire from fixture
Black wire from fixture
Figure 3
STEP 4 - Attach Ceiling Canopy to Mounting
Screw
A. Place the Ceiling Canopy on the top of the Fixture Body
(F) over the Mounting Screws (B) and secure with
Mounting Balls (E). Hand tighten until snug.
Fixture Body
Ceiling
Canopy
Figure 4
Figure 5
Mounting
Screw
Mounting
Ball
Need assistance with partsor assembly? Call Quoizelcustomer service at 1-631-273-2700
2012 Quoizel Inc.
Thank you for purchasinga Quoizel product.
or visit us on-lineat www.quoizel.com
4of6
July2012
Page 5
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
Assembly Instruction Sheet #IS-CRA1717MC
For Style CRA1717MC
STEP 5 - Attach Center Stem to Fixture Body
A. Thread beaded end of Center Stem (H) onto Hex Coupling
in the Fixture Body (F), hand tighten until snug
.
STEP 6 - Attach Shade to Fixture Body
A. Place Diffuser (G),Rubber Washer (I) and Flat Washer (J)
onto the Center Stem (H), secure by thread Hex Nut (K)
onto Center Stem (H). Hand tighten until snug.
Figure 6
Fixture
Body
Hex Coupling
Center Stem
Figure 7
Center Stem
STEP 7 -attach Finial to fixture
A. Thread Finial (L) onto Nipple, hand tighten until snug.
Diffuser
Rubber Washer
Flat Washer
1/8 Hex Nut
Figure 8
Nipple
Finial
Need assistance with partsor assembly? Call Quoizelcustomer service at 1-631-273-2700
2012 Quoizel Inc.
Thank you for purchasinga Quoizel product.
or visit us on-lineat www.quoizel.com
5of6
July2012
Page 6
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
Assembly Instruction Sheet #IS-CRA1717MC
For Style CRA1717MC
STEP 8Install Bulb-
A. This fixture uses standard bulb with a standard screw base.
Maximum 100 watts.
B. Insert bulb and screw properly into place.
Your fixture is now assembled and ready to use.
Enjoy!
Bulb
Socket
Figure 9
Need assistance with partsor assembly? Call Quoizelcustomer service at 1-631-273-2700
2012 Quoizel Inc.
Thank you for purchasinga Quoizel product.
or visit us on-lineat www.quoizel.com
6of6
July2012
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.