Page 1
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
Quoizel, Inc.
6 Corporate Parkway
Goose Creek, SC
29445
Customer Service
Phone 631.273.2700
Fax 631.231.7102
www.quoizel.com
,.
Assembly Instruction Sheet #IS-CPN8702EG
For Style CPN8702EG
ToolsRequired: Flathead screwdriver,Phillips screwdriver,pliers, wire cutters,wire
strippers,electrical tape, safetyglasses.
BulbRecommended: (2) CandelabraBase60W Maximum
EstimatedAssemblyTime:20-30 minutes
Preparation:Identify and inspectallparts before beginninginstallation.Check package
contentlist and diagramsbelowto be sureallparts are present.Ifany parts aremissing
ordamaged, do notattemptto assemble, install,oroperate the fixture.Contactcustomer
servicefor replacement parts.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing
the fixture. We strongly recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool
before removal. Do not subject glass parts to any shock while in operation or shattering may result.
Package Contents
Part
A Crossbar
B
C
D
E
F
G
H
Description
Nipple
Lock Washer
Hex Nut
Mounting Ball
Fixture Body
D30mm Crystal Ball with 4 Beads
D36mm Crystal Ball with 4 Beads
Quantity
1pc.
1pc.
1pc.
1pc.
1pc.
1pc.
8 pcs.
6 pcs.
A
B
F
C
D
E
G
H
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
2013 QuoizelInc.
Thank youfor purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
1of4
December2013
Page 2
CPN8702EG
FINISH: EMPIRE GOLD
17”
2.4 m m 13 Ga
GND
QU IOZEL
(2) 60W Candelabra
Base Bulbs
(No Supplied)
PART NUMBER
NO.
1
7”
13”
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2"
REPLACEMENT PART DESCRIPTION
2of4
REQ.
Page 3
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
Assembly Instruction Sheet #IS-CPN8702EG
For Style CPN8702EG
STEP 1 - Attach Crossbar to Outlet Box
A. Secure the Crossbar (A) to the outlet box with outlet
box screws (not supplied). Tighten until snug.
STEP 2 Attach Nipple to Crossbar-
A. Thread one Hex Nut (D) onto the top end of the Nipple
(B).
B. Place one Lock Washer (C) over the top end of the
Nipple (B) and then thread the Nipple (B) into the center
lock hole of the Crossbar (A).
C. Using pliers, thread the Hex Nut (D) against the
Crossbar (A) and hand tighten until snug.
STEP 3 Make Wire Connections-
Outlet Box
Mounting Hole
Lock Washer
Figure 1
Outlet Box Screw
(not Supplied)
Crossbar
Crossbar
Figure 2
Hex Nut
Nipple
A. Use standard wire connectors to make all wire
connections. (Connectors are not included with fixture.)
Strip and prepare wire ends according to instructions
supplied with connectors.
B. Connect White Supply Wire from the Outlet Box to White
Wire from fixture.
C. Connect Black (or Red) Supply Wire from the Outlet Box
to Black Wire from fixture.
D. Connect Ground Wire from the Outlet Box to Ground
Wire from fixture.
E. Twist connectors until wires are tightly joined together.
F. Wrap each connection with approved electrical tape and
carefully stuff all the connected wires into the Outlet Box.
White wire from supply White wire from fixture
Black wire from supply
(or Red)
Ground wire from supply Ground wire from fixture
Black wire from fixture
Figure 4
Figure 3
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
2013 QuoizelInc.
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
3of4
December2013
Page 4
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
Assembly Instruction Sheet #IS-CPN8702EG
For Style CPN8702EG
STEP 4 - Attach Fixture Body to Nipple
A. Place the Backplate of the Fixture Body (F) over the
Nipple (B) and secure with the Mounting Ball (E). Hand
tighten until snug.
Outlet Box
STEP 5 - Attach Crystal Ball with Beads onto
the Fixture Body
A. Attach D30mm Crystal Ball with 4 Beads (G) onto the
Leaves on the Fixture Body (F).
B. Attach D36mm Crystal Ball with 4 Beads (H) onto the
hangers on the SideArms and the Lower Arms.
Backplate
Nipple
Fixture
Body
Mounting
Ball
Side Arm
D36mm Crystal Ball
with 4 Beads
Leaf
Figure 5
Figure 6
STEP 6 - Install Bulb
A. This fixture uses candelabra bulbs with a standard screw
base. Maximum 60 watts.
B. Insert bulb and screw properly into place.
Your fixture is now assembled and ready to use.
Enjoy!
D30mm Crystal
Ball with 4 Beads
Lower
Arm
D36mm Crystal Ball
with 4 Beads
Bulb
Socket
Figure 7
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
2013 QuoizelInc.
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
4of4
December2013
Loading...