Page 1
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
INSTRUCTION SHEET IS-COR8409
STYLE NUMBER: COR8409K
PACKAGE CONTENTS
PART
A Crossbar
B
C
D
E
F
G
DESCRIPTION
Green Ground Screw
Nipple
Lock Washer
Hex Nut
Lock Ball
Fixture Body
QUANTITY
1pc
1pc
1pc
1pc
1pc
1pc
1pc
ISSUED 08-2010 REVISED 2010-09-30
A
B
C
D
E
F
G
WARNINGS AND CAUTIONS
WARNING:
● Before beginning the installation, turn off electricity at the circuit breaker box or the main fuse box by switching
off the circuit breaker or removing the fuse.
CAUTION:
● These instructions are provided for your safety. It is very important that they are read completely before the
installation of your fixture. We strongly recommend that a professional electrician install the fixture.
● Disconnect fixture from the power source before replacing the bulb(s), making sure that bulb(s) had sufficient
time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may result.
PREPARATION
● Before beginning installation of product, make sure all parts are present. Compare parts with package contents
list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or operate the
product. Contact customer service for replacement part.
● Estimated Assembly Time: 20 - 30 minutes
● Tool Required for Assembly (not included): Flathead screwdriver, Phillips screwdriver, Pliers, Electrical tape,
Wire cutter, Safety glasses and (1) 100W A19 medium base bulb
● Helpful Tools (not included): Wire strippers.
.
1OF5
Page 2
INSTALLATION INSTRUCTIONS
STEP 1:
a. Take apart the Cage with Shade from the Fixture Hood
by unscrewing the Lock Screws.
STYLE NUMBER: COR8409K
Lock Screw
Fixture Body
Fixture Hood
Cage with Shade
STEP 2:
a. Install the correct bulb referring to fixture markings and/or labels for maximum wattage.
STEP 3:
a. Place the Cage with Shade back into the Fixture Hood
and secure with Lock Screws. Hand-tighten until snug.
Fixture
Body
Cage with
Shade
Fixture Hood
Lock Screw
2OF5
Page 3
INSTALLATION INSTRUCTIONS
STEP 4:
a. Secure the Crossbar to the Outlet Box with Outlet Box
Screws.
STEP 5:
Pliers is required for this step.
a. Thread the Hex Nut onto one end of the Nipple.
b. Place the Lock Washer over the Hex Nut end of the
Nipple and then thread the Nipple into the center lock
hole of the Crossbar.
c. Using pliers, thread the Hex Nut against the Crossbar
and hand-tighten until snug.
Outlet Box
STYLE NUMBER: COR8409K
Crossbar
Outlet Box Screw
Crossbar
Hex Nut
Nipple
STEP 6:
Use Wire Connectors (not supplied) to connect the
wires.
a. Connect the House Ground Wire to the Fixture Ground
Wire.
b. Connect the House White (or Ribbed) Wire to the
Fixture Supply Wire (Black or Smooth Side).
c. Connect the House Black (or Red) Wire to the Fixture
Supply Wire (Black or Smooth Side).
d. Wrap each connection with approved electrical tape
and carefully stuff all of the connected wires into the
Outlet Box.
Lock Washer
WHITE OR RIBBED
FROM HOUSE
BLACK (OR RED) WIRE
FROM HOUSE
GROUND WIRE
FROM HOUSE
WHITE OR RIBBED
FROM FIXTURE
BLACK OR SMOOTH
FROM FIXTURE
GROUND WIRE
FROM FIXTURE
3OF5
Page 4
INSTALLATION INSTRUCTIONS
STEP 7:
a. Place the Backplate over the Outlet Box as shown.
Secure by threading the Lock Ball onto the Nipple.
Hand-tighten until snug.
STEP 8:
a. Refer to the following information for caulking instructions:
STYLE NUMBER: COR8409K
Outlet Box
Nipple
Backplate
Lock Ball
For assemble the MOUNTING BALLS, please note that
you are required to apply a small amount of Silicone
sealer to the threaded side of the MOUNTING BALLS
EXTERIOR GRADE
CAULK
MOUNTING BALL
and then install them onto the MOUNTING SCREWS.
With the OUTDOOR FIXTURE properly installed in accordance with supplied Assembly/installation instructions,
proceed with caulking instructions below.
Note: Be sure EXTERIOR WALL SURFACE and FIXTURE BACKPLATE are free to dirt to caulking. Using
EXTERIOR GRADE CAULK, start on one side of FIXTURE BACKPLATE and follow contour, were the FIXTURE
BACKPLATE meets the EXTERIOR WALL SURFACE upward. Proceed to caulk over top of backplate and down
other side. to ensure proper moisture drainage.DO NOT CAULK BOTTOM OF FIXTURE BACKPLATE
4OF5
Page 5
INSTALLATION INSTRUCTIONS
OUTDOOR
FIXTURE BACKPLATE
EXTERIOR WALL SURFACE
STYLE NUMBER: COR8409K
EXTERIOR GRADE
CAULK
Your installation is completed now. Restore electricity. Retain this sheet for future reference.
5OF5
Loading...