Quoizel CM8408AC User Manual

ASSEMBLY /INSTALLATION INSTRUCTIONS

6 CORPORATE PARKWAY GOOSE CREEK SC 29445 www quoizel com

(2)OUTLET BOX SCREWS

OUTLET BOX

ILLUSTRATION A

(not supplied)

CROSSBAR

BACKPLATE

CAGE

BOLT HOLDER

SOCKET

TAB

GLASS PANEL

DOOR

BOLT

Note If you find any Tabs do not engage Glass Panels well during assembly please push

: ,

the Tabs until they are attaching onto the Glass Panels

1. Before beginning the installation, carefully unpack and identify all parts referring to

illustration.

. .

2 Turn the electrical power to installation point OFF at circuit breaker 3 Open the Door on the Cage and install the correct bulb(s) referring to the fixture

markings and or labels for maximum wattage Proceed to close the Door by placing the Bolt onto the Bolt Holder

4 Refer to the Illustration B) Please note that the Backplate can be reversed. Remove the

Hex Nuts(small) and Washers(small) from the back of the Backplate. Loose the Hex Nut and the Lock Washer. And then push the Backplate as the arrow and reverse the Backplate up to down. Place the Studs back through the holes on the Backplate and then thread the Hex Nuts(small) and Washers(small) back onto the Studs. Hand tighten until snug. Proceed to tighten the Hex Nut and Lock Washer against the Backplate.

5 Place the Crossbar on the Backplate and align the holes in the side of the Backplate with the

threaded holes in the folded edge of Crossbar. Next, mount the Crossbar to the outlet box with (2)OUTLET BOX SCREWS (not provided).

6. :

Make the connections

Use wire connectors(not supplied) connect the House Ground Wire to the Fixture Ground

Wire; attach the House White Wire to Fixture White (or Ribbed Side) Supply Wire; connect the House Black (or Red) Wire to the Fixture Black (or Smooth Side) Wire. Wrap each connection with approved electrical tape.

7. Carefully tuck all wires into the Wall Mounted Outlet Box and position the fixture over the outlet box. Align the Holes in the side of Backplate with the 2 Mounting Holes on the folded edge of the Crossbar. Secure them by threading 2 Mounting Screws into the Mounting Holes

()

on the folded edge. Tighten until snug.

8.Refer to Page 2 for fixture caulking installations.

9. Restore power to the installation point ON. Retain this sheet for future reference.

FIXTURE SUPPLY WIRE

and GROUND WIRE

(2)MOUNTING SCREWS

IF IN DOUBT ABOUT ELECTRICAL INSTALLATION, CONSULT A LICENSED ELECTRICIAN!

BRACKET

CAGE

ILLUSTRATION B

HEX NUT and LOCK WASHER

BACKPLATE (reverse up to down)

HEX NUT (small)

WASHER (small)

IS-CM8408

Revised 2008 03 22

Page 1 of 2

6 CORPORATE PARKWAY GOOSE CREEK SC 29445 www quoizel com

FIGURE1

EXTERIOR GRADE CAULK

WALL SURFACE MOUNTED OUTDOOR FIXTURE

CAULKING INSTRUCTIONS

1 Refer to FIGURE2 For assemble the MOUNTING BALLS please note that you are required to apply a

.( ) ,

small amount of Silicone sealer to the threaded side of the MOUNTING BALLS and then install them onto the MOUNTING SCREWS

2 (Refer to FIGURE1 With the OUTDOOR FIXTURE properly installed in accordance with supplied

Assembly/installation instructions, proceed with caulking instructions below.

Note: Be sure EXTERIOR WALL SURFACE and FIXTURE BACKPLATE are free to dirt to caulking. Using EXTERIOR GRADE CAULK, start on one side of FIXTURE BACKPLATE and follow contour, were the FIXTURE BACKPLATE meets the EXTERIOR WALL SURFACE upward. Proceed to caulk over top of backplate and down other side. to ensure proper

DO NOT CAULK BOTTOM OF FIXTURE BACKPLATE

moisture drainage.

FIGURE2

OUTDOOR FIXTURE BACKPLATE

EXTERIOR WALLSURFACE

EXTERIOR GRADE CAULK

MOUNTING BALL

IS-CM8408

Revised 2008 03 22

Page 2 of 2