BulbRecommended: (3) Medium Base100W Maximum
EstimatedAssemblyTime:20-30 minutes
Preparation:Identify and inspectallparts before beginninginstallation.Check package
contentlist and diagramsbelowto be sureallparts are present.Ifany parts aremissing
ordamaged, do notattemptto assemble, install,oroperate the fixture.Contactcustomer
servicefor replacement parts.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing
the fixture. We strongly recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool
before removal. Do not subject glass parts to any shock while in operation or shattering may result.
Package Contents
Part
ACrossbar
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Description
Nipple
Lock Washer
Hex Nut
Ceiling Canopy
Canopy Chain Loop
Canopy Lock Ring
Fixture Chain
Fixture Loop
High Cap
Fixture Body
Short Cap
Finial
Socket Collar
Steel Collar
Shade
Quantity
1pc.
1pc.
2 pcs.
2 pcs.
1pc.
1pc.
1pc.
1pc.
1pc.
1pc.
1pc.
1pc.
1pc.
3 pcs.
3 pcs.
3 pcs.
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
2013 Quoizel Inc.
Thank youfor purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
1of6
June2014
CKAD5003PN
FINISH:
PALLADIAN BRONZE
QUIOZEL
GND
2.4 m m 13 G a
NOTE: TWO LIGHTS SHOWN FOR
ILLUSTRATION PURPOSES ONLY.
1
5” Dia.
1"
Overall Height 70”
(Includes 48” Chain)
(3)100W
Medium Base Bulb
(not Supplied)
PART NUMBER
NO.
4.5” Dia.
19.5”
6”
2
16.5” Dia.
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2"
REPLACEMENT PART DESCRIPTION
REQ.
1
M451CHPNCHAIN PALLADIAN BRONZE 4.5MMX4’1
2G3681SHSTONE SHADE ONYX 4.5"X6"H3
2of6
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
Assembly Instruction Sheet #IS-CKAD5003PN
For Style CKAD5003PN
STEP 1Adjust Fixture Assembly-
A. Unfold support arms on fixture assembly to proper
locations.
STEP 2 - Attach Short Cap and Finial to
Fixture Body
A. Place Short Cap (L) over the Nipple on the Bottom of
Fixture Body (K), make sure the side arm into the Gap
on the Short Cap (L). Secure by thread Finial (M) onto
Nipple, hand tighten until sung.
Nipple
Figure 1
Figure 2
Fixture Body
Short Cap
Finial
STEP 3 - Attach Fixture Loop to Fixture Body
A.HighJtop
PlaceCap ( ) over the Nipple on theof Fixture
Body (K), make sure the side arm into the Gap on the
HighJFixture Body I
Cap ( ). Secure by thread( ) onto
Nipple, hand tighten until sung.
STEP 4 - Attach Crossbar to Outlet Box
A. Secure the Crossbar (A) to the outlet box with outlet
box screws (not supplied). Tighten until snug.
Figure 3
Figure 4
Mounting
Hole
Fixture Loop
High Cap
Nipple
Fixture Body
Outlet Box
Crossbar
Outlet Box
Screw (not
Supplied)
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
2013 Quoizel Inc.
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
3of6
June2014
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
Assembly Instruction Sheet #IS-CKAD5003PN
For Style CKAD5003PN
STEP 5Attach Nipple to Crossbar-
A. Thread one Hex Nut (D) onto the top end of the Nipple
(B).
B. Place one Lock Washer (C) over the top end of the
Nipple (B) and then thread the Nipple (B) into the center
lock hole of the Crossbar (A).
C. Using pliers, thread the hex Nut (D) against the
Crossbar (A) and hand tighten until snug.
STEP 6 - Attach Canopy Chain Loop to Nipple
A. Thread another Hex Nut (D) onto the end of the Nipple
(B).
B. Place the Lock Washer (C) over the end of the Nipple
(B) and then thread the Canopy Chain Loop (F) onto the
end of the Nipple (B).
C. Using pliers, thread the Hex Nut (D) against the
Canopy Chain Loop (F) and hand tighten until snug.
Outlet Box
Crossbar
Lock Washer
Canopy
Chain Loop
Figure 5
Crossbar
Lock Washer
Hex Nut
Nipple
Nipple
Hex Nut
Figure 6
STEP 7Assemble Ceiling Canopy-
A. Push the Ceiling Canopy (E) upward over the Outlet
Box. Thread the Canopy Lock Ring (G) onto the Canopy
Chain Loop (F) and tighten until snug to secure the
Ceiling Canopy (E).
STEP 8Attach Fixture Chain to Canopy
-
Chain Loop and Fixture Loop
A. Adjust the Fixture Chain (H) to your desired length by
removing the links if needed. You may need to use plier
to open the chain links. If so, put a cloth over the chain
to protect the finish from the pliers.
B. Attach one end of the Fixture Chain (H) onto the
Canopy Chain Loop (F) and then attach the other end of
the Fixture Chain (H) onto the Fixture Loop.
Ceiling Canopy
Canopy
Lock Ring
Fixture Loop
Outlet Box
Canopy
Chian Loop
Figure 7
Canopy Chain Loop
Fixture Chain
Supply Wire and
Ground Wire
Figure 8
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
2013 Quoizel Inc.
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
4of6
June2014
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
Assembly Instruction Sheet #IS-CKAD5003PN
For Style CKAD5003PN
STEP 9Pass Supply Wires through Fixture
-
Chain
A. Pull the Supply Wires and Ground Wire up through the
Fixture Chain (H) alternating links. Push the wires up
through the Canopy Chain Loop (F) into the outlet box.
STEP 10 - Make Wire Connections
A. Un-thread the Canopy Lock Ring (G) and slide Canopy Lock
Ring (G) and Ceiling Canopy (E) down the Fixture Chain (H).
B. Push all slack fixture wire through Canopy Chain Loop (F)
into Outlet Box. Trim excess fixture wire leaving a minimum
of 6 inch. Hanging out of the Outlet Box.
C. Use standard wire connectors to make all wire connections.
(Connectors are not included with fixture.) Strip and prepare
wire ends according to instructions supplied with connectors.
D. Connect White Supply Wire from the Outlet Box to Ribbed
side Wire from fixture.
E. Connect Black (or Red) Supply Wire from the Outlet Box to
Smooth side Wire from fixture.
F. Connect Ground Wire from the Outlet Box to Ground Wire
from fixture.
G. Twist connectors until wires are tightly joined together.
H. Wrap each connection with approved electrical tape and
carefully stuff all the connected wires into the Outlet Box.
I. Re-attach the Ceiling Canopy (E) as shown in Step 7.
Supply Wire
and Ground
Wire from
Outlet Box
Canopy Chain
Loop
Fixture Chain
Supply Wire
and Ground Wire
Figure 9
Supply Wire and
Ground Wire
Canopy Chain Loop
Fixture Chain
Ceiling Canopy
Canopy Lock Ring
White wire from supplyRibbed side wire from fixture
Black wire from supply
(or Red)
Ground wire from supplyGround wire from fixture
Smooth side wire from fixture
Figure 11
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
2013 Quoizel Inc.
or visit us on-line at www.quoizel.com
5of6
Figure 10
June2014
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
Assembly Instruction Sheet #IS-CKAD5003PN
For Style CKAD5003PN
STEP 11 - Attach Shade to Fixture Body
A. Place Shade (P) andover the Socket,
Steel Collar (O)
secure by threading Socket Collar (N) to Socket.
Tighten until snug.
STEP 12Install Bulb-
A. This fixture uses standard bulbs with a standard screw
base. Maximum 100 watts.
B. Insert bulb and screw properly into place.
Your fixture is now assembled and ready to use.
Enjoy!
Socket Collar
Steel Collar
Shade
Socket
Figure 12
Figure 13
Bulb
Socket
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
2013 Quoizel Inc.
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
6of6
June2014
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.