Quoizel BWL2822CC User Manual
Assembly Instruction Sheet #IS-BWL2822CC
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
Quoizel, Inc.
6 Corporate Parkway
Goose Creek, SC 29445
Customer Service
Phone 631.273.2700
Fax 631.231.7102
www.quoizel.com
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Care of Tiffany Style Shade
A new tiffany lamp shade has an oil film applied to the shade that protects the tiffany shade from scratches during shipment. If the oil applied is
too heavy you can remove the excess oil film with a paper towel. Gently wipe away the excess oil.
For general cleaning of tiffany shades use a gentle lemon oil-based furniture polish applied to a soft cloth and wipe gently.
If a white powder appears on the soldered joints of the tiffany shade this is a normal oxidation process. Use a small amount of lemon oil or
mineral oil applied directly to oxidized areas and the soldered area will return to like new.
,.
For Style BWL2822CC
ToolsRequired: Flatheadscrewdriver, Phillipsscrewdriver,pliers,wire cutters, wire strippers, electricaltape,
safetyglasses.
BulbRecommended: (4) MediumBase 100W Maximum,Alternatebulb (4) 23W CFL
EstimatedAssembly Time:20-30minutes
Preparation:Identify and inspect all partsbeforebeginning installation. Check package contentlist and diagrams
belowto be sure all partsarepresent. If any parts aremissing or damaged, do not attemptto assemble, install, or
operatethe fixture. Contact customer serviceforreplacement parts.
Package Contents
Ceiling
A
Canopy
x1
Lock Ball
B
x2
6” Rod
C
x2
STEP 1 Assemble Rods-
A. Determine the Rods (C/D/E) to
be assembled to the Shade (F)
according to your hanging
height.
B. Pass Supply Wires and Ground
Wire through the chosen Rods
(C/D/E) and then thread the
chosen Rods (C/D/E) and
Shade (F). Hand tighten until
snug.
C. Pass Supply Wires and Ground
Wire through the Ceiling
Canopy (A) and then thread the
Ceiling Canopy (A) and the
Upper Rod together. Hand
tighten until snug.
D
E
F
12” Rod
x1
A
C
C
H
12” Rod
with Nipple
x1
F
G
Rubber Washer
x1
Flat Washer
I
x1
J
K
E
Shade
x1
Diffuser
x1
Hex Nut
x1
Finial
x1
Figure 1
D
Hardware Contents
ND
G
STEP 2 Install Crossbar-
A. Attach the Crossbar Assembly (AA) to the Outlet Box with the head
of the Green Ground Screw facing you. Secure it with Outlet Box
Screws (not included) Tighten until snug
Green Ground Screw
STEP 3 - Attach Lanyard
A. The purpose of the lanyard is to provide the installer a means to
support the fixture from the junction box while connecting the
electrical wires. This enables the fixture to hang from the junction
box and your hands are free to make the wire connections.
B. Turn the Button Stop so it may be inserted into the Inner Backplate
slot. Make sure the Button Stop is completely inside the crossbar.
Slowly release the fixture to make sure it is supported by the Button
Stop. Proceed to the wiring steps. Once you are complete with the
wiring there is nothing to do with Lanyard. The Lanyard will push
into the junction box when the fixture is placed for final mounting.
Crossbar
..
Crossbar Assembly
AA
x1
Outlet Box
AA
Outlet Box Screw
(not included)
Button Stop
Lanyard
Figure 2
Figure 3
2014 Quoizel Inc.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
1of2
February2014
STEP 4 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Strip and
prepare wire ends according to instructions supplied with
connectors.
B. Connect White Supply Wire from the Outlet Box to Ribbed side
Wire from fixture.
C. Connect Black (or Red) Supply Wire from the Outlet Box to Smooth
side Wire from fixture.
D. Connect Ground Wire from the Outlet Box to Ground Wire from
fixture.
E. Twist connectors until wires are tightly joined together.
F. Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from supply
Black wire from
supply (or Red)
Ground wire
from supply
Ribbed side wire
from fixture
Smooth side wire
from fixture
Ground wire
from fixture
Figure 4
STEP 5 Attach Fixture Body to Mounting Screw-
A. Place the Backplate of the Fixture Body (A) over the Mounting
Screws and secure with Lock Ball (B). Hand tighten until snug.
STEP 6 Attach Shade to fixture-
A. Place the Diffuser (G) , Rubber Washer (H) and Flat Washer (I)over
the Center Stem, secure with the Hex Nut (J). Hand tighten until
sung.
B. Thread the Finial (K) onto the Center Stem, hand tighten until sung.
F
G
I
H
J
Figure 6
K
STEP 7 Install Bulb-
A. This fixture uses standard bulb with medium screw base. Maximum
100 watts.
B. Insert bulb and screw snugly into place.
Your fixture is now assembled and ready to use.
Enjoy!
Socket
A
BWL2822CC
FINISH: COPPER CANYON
ND
G
Mounting Screw
B
Figure 5
5.5” Dia.
21” Dia.
22” Dia.
1”
Bulb
49”
OVERALL HEIGHT INCLUDES
(2) 6” AND (2) 12” RODS
11”
10”9.5”
2
3
Figure 7
1
(4) 100W
Base
(Not Supplied)
PART NUMBER
NO.
9008EXCC
1
9007EXCC
2
G147DI
3
2014 Quoizel Inc.
Medium
Bulbs
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2"
REPLACEMENT PART DESCRIPTION
ROD COPPER CANYON 12"LX .63"DEXTENSION
ROD COPPER CANYON 6"LX .63"DEXTENSION
DIFFUSER FROSTED GLASS 20.25"D
REQ.
2
2
1
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2of2
February2014
Loading...