Quoizel BWL1717CC User Manual
Assembly Instruction Sheet #IS-BWL1717CC
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
Quoizel, Inc.
6 Corporate Parkway
Goose Creek, SC 29445
Customer Service
Phone 631.273.2700
Fax 631.231.7102
www.quoizel.com
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Care of Tiffany Style Shade
A new tiffany lamp shade has an oil film applied to the shade that protects the tiffany shade from scratches during shipment. If the oil applied is
too heavy you can remove the excess oil film with a paper towel. Gently wipe away the excess oil.
For general cleaning of tiffany shades use a gentle lemon oil-based furniture polish applied to a soft cloth and wipe gently.
If a white powder appears on the soldered joints of the tiffany shade this is a normal oxidation process. Use a small amount of lemon oil or
mineral oil applied directly to oxidized areas and the soldered area will return to like new.
,.
For Style BWL1717CC
ToolsRequired: Flatheadscrewdriver, Phillipsscrewdriver,pliers,wire cutters, wire strippers, electricaltape,
safetyglasses.
BulbRecommended: (3) MediumBase 100W Maximum,Alternatebulb (3) 23W CFL
EstimatedAssembly Time:30-45minutes
Preparation:Identify and inspect all partsbeforebeginning installation. Check package contentlist and diagrams
belowto be sure all partsarepresent. If any parts aremissing or damaged, do not attemptto assemble, install, or
operatethe fixture. Contact customer serviceforreplacement parts.
Package Contents
Diffuser
D
x1
Ceiling Canopy
A
x1
Shade
B
x1
Lock Ball
C
x2
STEP 1 Install Crossbar-
A. Attach the Crossbar Assembly (AA) to the Outlet Box with the head
of the Green Ground Screw facing you. Secure it with Outlet Box
Screws (not included) Tighten until snug
Green Ground Screw
STEP 2 - Wire Connections
..
Outlet Box
AA
Outlet Box Screw
(not included)
Rubber Washer
E
x1
Flat Washer
F
x1
Hex Nut
G
x1
Finial
H
x1
Figure 1
Hardware Contents
Crossbar Assembly
ND
G
B. Connect White Supply Wire from the Outlet Box to Ribbed side
Wire from fixture.
C. Connect Black (or Red) Supply Wire from the Outlet Box to Smooth
side Wire from fixture.
D. Connect Ground Wire from the Outlet Box to Ground Wire from
fixture.
E. Twist connectors until wires are tightly joined together.
F. Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from supply
Black wire from
supply (or Red)
Ground wire
from supply
STEP 3 Attach Shade to Ceiling
A. Thread Ceiling Canopy (A) onto
-
Canopy
the Shade (B). Hand tighten
until snug.
AA
x1
Ribbed side wire
from fixture
Smooth side wire
from fixture
Ground wire
from fixture
Figure 2
Figure 3
A
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Strip and
prepare wire ends according to instructions supplied with
connectors.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
2014 Quoizel Inc.
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
B
February2014
1of2
STEP 4 Attach Fixture Body to
-
Mounting Screw
A. Place the Ceiling Canopy (A)
over the Mounting Screws and
secure with Lock Ball (C). Hand
tighten until snug.
STEP 5 Attach Shade to fixture-
A. Place the Diffuser (D) , Rubber
Washer (E) and Flat Washer
(F)over the Center Stem,
secure with the Hex Nut (G).
Hand tighten until sung.
B. Thread the Finial (H) onto the
Center Stem, hand tighten until
sung.
BWL1717CC
FINISH: COPPER CANYON
Figure 4
Mounting Screw
A
C
STEP 6 Install Bulb-
A. This fixture uses standard bulb
with medium base . Maximum
100 watts.
B. Insert bulb and screw snugly
into place.
Socket
Your fixture is now assembled
and ready to use. Enjoy!
B
Bulb
Figure 6
Center Stem
D
E
F
G
H
Figure 5
1”
5.5” Dia.
(3) 100W
Base
(Not Supplied)
PART NUMBER
NO.
1
2
ND
G
Medium
Bulbs
11”
5.5”
6”
16” Dia.
17” Dia.
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2"
REPLACEMENT PART DESCRIPTION
REQ.
2014 Quoizel Inc.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
2of2
February2014
Loading...