Quoizel BRY8406PN User Manual
Assembly Instruction Sheet #IS-BRY8406PN
For Style BRY8406PN
Quoizel, Inc.
6 Corporate Parkway
Goose Creek, SC 29445
Customer Service
Phone 631.273.2700
Fax 631.231.7102
www.quoizel.com
ToolsRequired: Flatheadscrewdriver, Phillipsscrewdriver,pliers,wire cutters, wire strippers, electricaltape,
safetyglasses.
BulbRecommended: (1) MediumBase 100W Maximum,Alternatebulb (1) 23W CFL
EstimatedAssembly Time:
Preparation:
belowto be sure all partsarepresent. If any parts aremissing or damaged, do not attemptto assemble, install, or
operatethe fixture. Contact customer serviceforreplacement parts.
Fixturecan only be mounted inthedirection indicated on page 2.
Identifyand inspect all parts beforebeginninginstallation. Check package content listand diagrams
30-45minutes
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Package Contents
A
Fixture
Body
x1
Hardware Contents
STEP3 - Wire Connections
Crossbar Assembly
AA
x1
STEP 1 Install Crossbar-
A. Pass the supply wires through the Crossbar Assembly (AA). Attach
the Crossbar Assembly (AA) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included). Tighten until snug.
Supply Wires with
Outlet Box
Figure 1
STEP 2 Fit Fixture Body to Crossbar
A. Remove mounting balls from the
-
Assembly
Crossbar Assembly (AA). Fit the
Fixture Body (A) Crossbar Assembly
(AA) and secure with mounting balls.
Note: The backplate of the Fixture
Body (A) should be snug against the
wall surface and the mounting balls. If
not, adjust the length of the nipple on
the Crossbar Assembly (AA) by
unscrewing the preassembled hex nut
and lock washer and then screwing
the mounting screws in or out of the
crossbar until the correct length is
achieved. Once the backplate of the
Fixture Body (A) is secure, remove the
mounting ball and Fixture Body (A)
and proceed to Step 3.
Ground Wire
AA
Outlet Box Screws
(not included)
Mounting
Ball
Hex Nut and
Lock Washer
AA
Mounting
Screw
A
Figure 2
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Strip and
prepare wire ends according to instructions supplied with
connectors.
B. Connect White Supply Wire from the Outlet Box to Ribbed side Wire
from fixture.
C. Connect Black (or Red) Supply Wire from the Outlet Box to Smooth
side Wire from fixture.
D. Connect Ground Wire from the Outlet Box to Ground Wire from
fixture.
E. Twist connectors until wires are tightly joined together.
F. Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from supply
Black wire from
supply (or Red)
Ground wire
from supply
STEP 4 Install Fixture Body-
A. Carefully tuck all wires into the outlet
box and position the backplate of
fixture body (A) over the outlet box.
Align the holes in the backplate with
the mounting screws. Place caulk (not
supplied) into the previously removed
mounting balls and then attach fixture
body (A) using the mounting balls.
Hand tighten until snug.
Figure 3
Figure 4
Ribbed side wire
from fixture
Smooth side wire
from fixture
Ground wire
from fixture
Mounting
A
Ball
Hex Nut and
Lock Washer
AA
Mounting
Screw
2014 QuoizelInc.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
1of2
March2014
STEP 5 - Install Bulb
STEP 6 - Apply Silicone Sealer
A. This fixture uses standard bulb with medium
base . Maximum 100 watts.
B. Insert bulb and screw snugly into place.
Socket
Figure 5
BRY8406PN
FINISH: PALLADIAN BRONZE
Fixture can only be
mounted in the
direction indicated
65."
Bulb
A. Make sure exterior wall surface
and fixture backplate are free of
dirt before applying caulk. Using
exterior grade caulk, caulk over
top of backplate and down other
side. Do not caulk bottom of
fixture backplate to ensure proper
moisture drainage.
Your fixture is now assembled and
ready to use. Enjoy!
9"
12.5”
Exterior
Grade
Caulk
Backplate
Figure 6
65 Sq.."
45."
(1) 100W
(Not Supplied)
NO.
1
Medium
Base
Bulbs
PART NUMBER
G3831PA CLEAR SEEDY GLASS PANEL 4
NOTE: ALL DIMENSIONS ARE ROUNDED UPTO THE NEAREST 1/2"
REPLACEMENT PART DESCRIPTION
1
REQ.
2014 QuoizelInc.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
2of2
March2014
Loading...