Page 1
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
INSTRUCTION SHEET IS-BRB2822
STYLE NUMBER: BRB2822K
PACKAGE CONTENTS
PART
A Crossbar
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
DESCRIPTION
Green Ground Screw
Mounting Screw
Lock Washer
Small Hex Nut
Mounting Ball
Rubber Washer
Flat Washer
1/8 IP Hex Nut
Finial
Center Stem Assembly
6” Rod
12” Rod
Finial
Ceiling Canopy
Shade with Sockets
Diffuser
QUANTITY
1pc
1pc
2pcs
2pcs
2pcs
2pcs
2pcs
1pc
1pc
1pc
1pc
2pcs
2pcs
1pc
1pc
1pc
1pc
ISSUED 07-2010
A
O
B
C
D
E
F
G
H
I
J
K
P
Q
L
M
WARNINGS AND CAUTIONS
WARNING:
● Before beginning the installation, turn off electricity at the circuit breaker box or the main fuse box by switching
off the circuit breaker or removing the fuse.
CAUTION:
● These instructions are provided for your safety. It is very important that they are read completely before the
installation of your fixture. We strongly recommend that a professional electrician install the fixture.
● Disconnect fixture from the power source before replacing the bulb(s), making sure that bulb(s) had sufficient
time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may result.
1OF4
Page 2
PREPARATION
STYLE NUMBER: BRB2822K
● Before beginning installation of product, make sure all parts are present. Compare parts with package contents
list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or operate the
product. Contact customer service for replacement part.
● Estimated Assembly Time: 20 - 30 minutes
● Tool Required for Assembly (not included): Flathead screwdriver, Phillips screwdriver, Pliers, Electrical tape,
Wire cutter, Safety glasses and (4) 100W A19 medium base bulbs
.
● Helpful Tools (not included): Wire strippers.
INSTALLATION INSTRUCTIONS
STEP 1:
a. Determine the Rods to be assembled according to your
desired hanging height.
b. Pass the Supply Wires with Ground Wire through the
chosen Rods and then thread Rods and Shade with
Sockets together as shown. Hand-tighten until snug.
6” Rod
6” Rod
STEP 2:
a. Pass the Supply Wires with Ground Wire through the
Swivel and Ceiling Canopy.
b. Thread the Swivel onto the top end of the Upper Rod.
Hand-tighten until snug.
12” Rod
Coupling
12” Rod
Supply Wires with
Ground Wire
Shade with
Sockets
Ceiling Canopy
Swivel
2OF4
Supply Wire with
Ground Wire
Upper Rod
Page 3
INSTALLATION INSTRUCTIONS
STYLE NUMBER: BRB2822K
STEP 3:
a. Screw the Mounting Screws into the Crossbar place
the Lock Washers over the Mounting Screws and
thread the Hex Nuts onto the Mounting Screws as
shown Secure the position of the Mounting Screws by
.
tightening the Hex Nuts against the Crossbar
b. Secure the Crossbar to the Outlet Box with Outlet Box
Screws
.
,
.
STEP 4:
Use Wire Connectors (not supplied) to connect the
wires.
a. Connect the House Ground Wire to the Fixture Ground
Wire.
b. Connect the House White (or Ribbed) Wire to the
Fixture Supply Wire (Black or Smooth Side).
c. Connect the House Black (or Red) Wire to the Fixture
Supply Wire (Black or Smooth Side).
d. Wrap each connection with approved electrical tape
and carefully stuff all of the connected wires into the
Outlet Box.
Mounting Screw
Outlet Box
WHITE OR RIBBED
FROM HOUSE
BLACK (OR RED) WIRE
FROM HOUSE
GROUND WIRE
FROM HOUSE
Crossbar
Hex Nut
Lock Washer
Outlet Box Screw
WHITE OR RIBBED
FROM FIXTURE
BLACK OR SMOOTH
FROM FIXTURE
GROUND WIRE
FROM FIXTURE
STEP 5:
a. Place the Ceiling Canopy over the Mounting Screws
and secure with the Mounting Balls. Hand-tighten until
snug.
Mounting
Screw
Outlet Box
Ceiling
Canopy
Mounting Ball
3OF4
Page 4
INSTALLATION INSTRUCTIONS
STEP 6:
a. Screw the short nipple end of the Center Stem
Assembly into the Hex Coupling underside of the
Junction Box inside of the Shade. Hand-tighten until
snug.
b. Place the Rubber Washers, the Diffuser and the Flat
Washer over the end of the Center Stem Assembly as
shown. Secure them by threading the 1/8 IP Hex Nut
onto the Center Stem. Tighten until snug.
c. Thread the Finial onto the end of the Center Stem
Assembly. Hand-tighten until snug.
STYLE NUMBER: BRB2822K
Shade
Center Stem Assembly
Diffuser
STEP 7:
a. Install correct bulbs referring to fixture markings and/or labels for maximum wattage.
Your installation is completed now. Restore electricity. Retain this sheet for future reference.
Junction Box
Hex Coupling
Rubber Washer
Rubber Washer
Flat Washer
1/8 IP Hex Nut
Finial
4OF4
Loading...