Quoizel ALZ5005PN User Manual

Assembly Instruction Sheet #IS-ALZ5005PN

6 CORPORATE PARKWAY GOOSE CREEK SC 29445 www quoizel com

Quoizel, Inc. 6 Corporate Parkway Goose Creek, SC 29445

Customer Service Phone 631.273.2700 Fax 631.231.7102 www.quoizel.com

For Style ALZ5005PN

ToolsRequired: Flatheadscrewdriver, Phillipsscrewdriver,pliers,wire cutters, wire

strippers,electrical tape, safety glasses.

BulbRecommended: alternatebulbs (5) Medium Base 23WCFL(5)Medium Base 100W Maximum, EstimatedAssembly Time:35-40minutes

Preparation:Identify and inspect all partsbeforebeginning installation. Check package

contentlist and diagrams below tobesure all parts are present.If any parts are missing ordamaged, do not attempt toassemble,install, or operate the fixture.Contact customer servicefor replacement parts.

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject glass parts to any shock while in operation or shattering may result.

Package Contents

Fixture Loop

Socket Assembly

STEP 1 - Attach Fixture Loop to

A. Unfold Support Arms of the Fixture

B. Thread the Fixture Loop (A) onto

Fixture Assembly

Assembly (B) to proper locations. (Refer to Shade Orientation)

the nipple on the top end of the Fixture Assembly (B). Hand tighten until snug.

Socket Collar Tool

SHADE ORIENTATION

Socket Collar x5

Shade

Figure 1

Hardware Contents

Crossbar

Lock Washer

Hex Nut

Nipple

Canopy Chain Loop

Canopy Lock Ring

Fixture Chain

Ceiling Canopy

Step B

Step A

Figure 3

STEP 2 Install Crossbar-

A. AA)Attach the Crossbar ( to the Outlet Box with the head of the

Green Ground Screw facing you. Secure it with Outlet Box Screws (not included) Tighten until snug..

Outlet Box

Outlet Box Screw (not included)

Figure 2

2013 QuoizelInc.

Green Ground Screw

Thank you for purchasing a Quoizel product.

Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700

or visit us on-line at www.quoizel.com

STEP 3 Install Canopy Chain Loop and Nipple-

* Pliers is required for this step.

A. Thread one Hex Nut (CC) to one end of the Nipple (DD) until it is at

least 0.25” from the end. Pass one Lock Washer (BB) over the end of the Nipple (DD) and thread the Canopy Chain Loop (EE) onto the Nipple (DD). By using pliers, thread the Hex Nut (CC) against the Canopy Chain Loop (EE) and hand tighten until snug.

B. Thread another Hex Nut (CC) to the middle of the Nipple (DD).

Place another Lock Washer (BB) over the Nipple (DD) and then thread the Nipple (DD) into the Crossbar (AA) until the Nipple (DD)

December2013

1of3

Is about 0.375” above the Crossbar (AA).

C. Remove the Canopy Lock Ring (FF) from the Canopy Chain Loop

(EE). Place the Ceiling Canopy (HH) over the Canopy Chain Loop (EE) against the ceiling to determine the correct position of the Nipple (DD). Thread the Canopy Lock Ring onto the Canopy Chain Loop (EE). Adjust the Nipple (DD) to allow the Ceiling Canopy (HH) to rest against the ceiling when held in place by the Canopy Lock Ring (FF).

D. Remove the Canopy Lock Ring (FF) and the Ceiling Canopy (HH).

Tighten the Hex Nut (CC) against the Crossbar (AA) to secure in place.

STEP 4 - Install Fixture Chain and Ceiling Canopy

A. Adjust the Fixture Chain (HH) to your desired length by removing

the links if needed.

Pliers is required for this step.

B. With the Fixture Chain (HH) not attached to the Fixture Loop (A) and

the Canopy Chain Loop (EE), pull the supply wires through the Fixture Chain (GG) alternating links.After the wires are through the Fixture Chain (GG), pull the Supply Wires and the Ground Wire through the Canopy Lock Ring (FF) and the Ceiling Canopy (HH) in order.

C. Attach one end of the Fixture Chain (GG) to the Fixture Loop (A) and

close the chain loop. Lift the fixture and Fixture Chain (GG) up And Attach the other end of the Fixture Chain (GG) onto the Canopy Chain Loop (EE). The fixture will now hang safely. Close the chain loop at the Ceiling Canopy Loop (EE).

D. Feed the Supply Wires and Ground Wire through the Canopy Chain

Loop (EE) and Nipple (DD) into the Outlet Box. Cut the wires leaving

approximately 8” of wire extending from the Outlet Box. E. Refer to Step 6 for wire connections. F. Raise the Ceiling Canopy (HH) and Canopy Lock Ring (FF) up the

Fixture Chain (GG) and over the Canopy Chain Loop (EE). Tighten

the Canopy Lock Ring (FF) onto the Canopy Chain Loop (EE) until

tight.

Suggested chain length for Ceiling height :

8’ ceiling : use 4 links of chain

9’ ceiling : use 13 links of chain

10’ ceiling : use 23 links of chain

STEP 5 - Wire Connections

A. Use standard wire connectors (not included) to make all wire

connections. (Connectors are not included with fixture.) Strip and prepare wire ends according to instructions supplied with connectors.

B. Connect White Supply Wire from the Outlet Box to Ribbed side

Wire from fixture.

C. Connect Black (or Red) Supply Wire from the Outlet Box to Smooth

side Wire from fixture.

D. Connect Ground Wire from the Outlet Box to Ground Wire from

fixture. E. Twist connectors until wires are tightly joined together. F. Wrap each connection with approved electrical tape and carefully

stuff all the connected wires into the Outlet Box.

White wire

from supply

Black wire from supply (or Red)

Ground wire

from supply

Figure 5

STEP 6 Install Shade-

A. Place the Shade (E) over the

Socket as shown. By using the Socket Collar Tool (C), thread the Socket Collar (D) onto the Socket. Hand tighten until snug to secure the Shade (E).

Ribbed side wire from fixture

Smooth side wire from fixture

Ground wire from fixture

Socket

Supply Wires

and Ground Wire

Figure 6

STEP 7 Install Bulb-

A. This fixture uses standard bulb with

medium base . Maximum 100 watts.

B. Insert bulb and screw snugly into

place.

Your fixture is now assembled and ready to use. Enjoy!

Figure 4

Bulb

Socket

Figure 7

2013 QuoizelInc.

Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700

Thank you for purchasing a Quoizel product.

or visit us on-line at www.quoizel.com

2of3

December2013

+ 1 hidden pages