Page 1
Assembly Instruction Sheet #IS-ADS8701DC
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
Quoizel, Inc.
6 Corporate Parkway
Goose Creek, SC
29445
Customer Service
Phone 631.273.2700
Fax 631.231.7102
www.quoizel.com
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing
the fixture. We strongly recommend that a licensed, professional electrician perform the installation.
,.
ToolsRequired:Flatheadscrewdriver,Phillipsscrewdriver,pliers, wire cutters,wire
strippers,electricaltape,safety glasses.
BulbRecommended: (1) CandelabraBase60WMaximum
EstimatedAssemblyTime: 20-30minutes
Preparation:Identifyandinspect all partsbeforebeginninginstallation. Check package
contentlistanddiagrams below tobesureall parts arepresent.Ifany parts aremissing
ordamaged,donot attempt toassemble,install,or operate thefixture.Contactcustomer
serviceforreplacementparts.
Warnings and Cautions
For Style ADS8701DC
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool
before removal. Do not subject glass parts to any shock while in operation or shattering may result.
Package Contents
Part
A Crossbar
B
C
D
E
F
G
H
I
J
K
L
Description
Mounting Screw
Lock Washer
Hex Nut
Mounting Ball
Fixture Body
Socket Collar
Shade Holder A
Shade Holder B
Shade A
Shade B
Socket Collar Tool
Quantity
1pc.
2 pcs.
2 pcs.
2 pcs.
2 pcs.
1pc.
1pc.
1pc.
1pc.
1pc.
1pc.
1pc.
A
B
C
D
E
F
G
H
I
K
J
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
2011 Quoizel Inc.
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
1of5
L
September2011
Page 2
ADS8701DC
FINISH: DARK CHERRY
2.4mm
13Ga
R
QUOIZEL
GND
1
2
14”
5” Dia.
4” Dia.
3” Dia.
3
5.5”
4.5”
(1)60W Candelabra
base bulb
(not Supplied)
PART NUMBER
NO.
1
2
3
9511KIT
G2940SH
G2939SH
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2"
REPLACEMENT PART DESCRIPTION
MTG HDW/CNPY DARK CHERRY 4”D
SHADE CLEAR WATER GLS 5.5"H
SHADE OPAL ETCHED GLS 4.5"H
2of5
7”
REQ.
1
1
1
Page 3
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
Assembly Instruction Sheet #IS-ADS8701DC
For Style ADS8701DC
STEP 1 - Attach Mounting Screws, Lock
Washers and Hex Nuts to Crossbar
A. Line up a set of holes on the Crossbar (A) and Holes on
the backplate of the Fixture Body (F).
B. Thread Mounting Screws (B) into the holes on the
Crossbar (A), pass Lock Washers (C) and thread Hex
Nut (D) onto the Mounting Screws (B). Hand tighten
until snug.
STEP 2 - Attach Crossbar to Outlet Box
A. Attach the Crossbar (A) to Outlet Box and secure by
threading Outlet Box Screws (not supplied) into the
Mounting Holes on the Outlet Box. Tighten until snug.
Mounting
Screw
Crossbar
Figure 1
Lock Washer
Hex Nut
Outlet
Box
Fixture Body
Crossbar
Mounting
Hole
Outlet Box
Screw
Figure 2
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
2011 Quoizel Inc.
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
3of5
September2011
Page 4
Assembly Instruction Sheet #IS-ADS8701DC
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
STEP 3 Make Wire Connections-
A. Use standard wire connectors to make all wire
connections. (Connectors are not included with fixture.)
Strip and prepare wire ends according to instructions
supplied with connectors.
B. Connect White Supply Wire from the Outlet Box to White
Wire from fixture.
C. Connect Black (or Red) Supply Wire from the Outlet Box
to Black Wire from fixture.
D. Connect Ground Wire from the Outlet Box to Ground
Wire from fixture.
E. Twist connectors until wires are tightly joined together.
F. Wrap each connection with approved electrical tape and
carefully stuff all the connected wires into the Outlet Box.
White wire from supply White wire from fixture
,.
For Style ADS8701DC
Figure 3
Black wire from supply
(or Red)
Ground wire from supply Ground wire from fixture
Black wire from fixture
Figure 4
STEP 4 - Attach Fixture Body to Mounting
Screw
A. Place the backplate of the Fixture Body (F) over the
Mounting Screws (B) and secure with Mounting Balls
(E). Hand tighten until snug.
Mounting Screw
Figure 5
Backplate
Mounting Ball
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
2011 Quoizel Inc.
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
4of5
September2011
Page 5
Assembly Instruction Sheet #IS-ADS8701DC
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
STEP 5 - Attach Shade to Fixture Body
A. Place the Shade B (K), the Shade Holder B (I), the
Shade A (J) and the Shade Holder A (H) over the Socket
as shown. By using the Socket Collar Tool (L), thread
the Socket Collar (G) onto the Socket to secure above
parts. Hand tighten until snug.
,.
For Style ADS8701DC
Socket Collar Tool
Socket Collar
Shade Holder A
Shade A
Shade Holder B
Shade B
Socket
STEP 6 Install Bulb-
A. This fixture uses candelabra bulb with a candelabra
screw base. Maximum 60 watts.
B. Insert bulb and screw snugly into place.
Your lamp wall fixture is now assembled and ready to
use. Enjoy!
Figure 6
Bulb
Socket
Figure 7
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
2011 Quoizel Inc.
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
5of5
September2011
Loading...