SMART
SWITCH
TAP T
INTHEBOX
• Wall switch ass embly kit with pre -stripped,
stranded wires (green, red, white, and black),
and 4 wire connectors (for wires up to
12 gauge)
• Faceplate (hides visible screws)
• Snap plate (pre-attached)
• User guide
Note: The in cluded faceplat e and snap plate
are intend ed for single gan g box installatio ns
only. If insta lling in a double g ang box, use a
double ga ng wall plate (not incl uded) without
the faceplate and snap plate.
WHATYOU’LLN EED
• A Wink HUB or ZigBee-enabled, Winkcertified hub (sold separately)
• Apple® or Android™ smart device (tablets
and desktops not supported)
• The Wink app downloaded to your mobile
device from t he iTunes® App Store or Go ogle
Play™. If you alrea dy have the Wink app
installed, please download the latest version
to ensure you h ave the most updated s upport.
• A Wi-Fi® network connection with a router
using WPA-PSK security. WEP security is
not supported. Please refer to your router’s
manual for instructions on converting your
router to WPA security.
• Slotted screwdriver and Phillips head
screwdriver
IMPORTANT SAFETY INFORMATION
• Read all instructions and warnings prior to
using Tapt. Failure to comply with instructions
and warnings constitutes improper use of Tapt.
Save all instructions.
• Quirky, Inc. not responsible for improper
use, which m ay result in person al injury or
product damage.
• Not a toy. Keep away from c hildren.
• WARNING: RISK OF ELECTRIC SHOCK
OR FIRE . Before installing, servicing, or
removing Tapt, T URN OFF POWER AT THE
CIRCUIT BR EAKER THAT CONTROLS THE
SWITCH. Aer pow er has been turne d off,
make sure the l ight switch you are go ing to
replace with Tapt is powered down before
continuing installation. It is recommended to
use a circuit t ester to make sure the ci rcuit
is off. Exercise extreme caution when using
devices controlled via Tapt.
• This devic e is intended for ins tallation and
use in accordance with the National Electric
Code (NEC) an d local regulat ions in the United
States, or t he Canadian Ele ctrical Cod e (CEC)
and local regulations in Canada. If you are
unsure or uncomfortable about performing
this installation, consult a qualified electrician.
• Tapt is a single po le switch and a neutr al
connection is required.
• Tapt is not compat ible with a 3-way li ght switch.
• NOT FOR US E WITH MEDI CAL OR LIFE
SUPPORT EQUIPMENT. App-enabled
devices sho uld never be used to su pply power
to or control th e On/Off status
of medical and/or life support equipment.
• Do not use to con trol electric h eaters or
any other appliances which may present a
hazardous condition due to unattended or
unintentional or automatic power on control.
• 120VAC. Must not exce ed 600 watts
(Incandescent); 15 Amps, 1800W (Resistive);
or 1⁄2 HP (Motor). The maximum rating for
entire switc h is 1800W (15A ) Resistive.
• There are no user-serviceable parts.
• Only use this device with copper or copperclad wires.
COMPLIANCE
This device c omplies with P art 15 of the FCC Ru les.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this devi ce must accept an y interferen ce received,
including interference that may cause undesired
operation.
Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.
NOTE: This equipment has been tested and found
to comply wit h the limits fo r a Class B digita l device,
pursuant t o Part 15 of the FCC Ru les. These li mits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum
distance 2 0cm betwee n the radiator & yo ur body.
The country code selection is for non-US models only
and is not avai lable to all US mo dels. Per FCC
regulati ons, all Wi- Fi products m arketed in US mus t be
fixed to US operation channels only.
This device complies with Industry Canada licenceexempt RSS standard(s). Operation is subject to the
following two conditions:
(1) this device may not cause interference, and (2)
this device must accept any interference, including
interference that may cause undesired operation of
the device.
LIMITE DONEYEARWARR ANTY
Quirky, Inc. (“Quirky”) Original Purchase Product
Warranty:
Quirky warrants to the original purchaser (“Purchaser”) of
this Quirky product, for the period of one (1) year following
the date on which Purchaser purchases the product, that
the produc t shall be free o f defects in de sign, asse mbly,
material, or workmanship.
Quirky w ill refund or rep lace, at its opt ion, any defe ctive
product free of charge.
In order to qualify for this warranty, the Purchaser must
provide the defective product and a copy of the original
receipt of pu rchase to Quir ky for inspe ction. The r eceipt of
purchase must indicate the product purchased, price paid,
date of purchase, and name of merchant.
To request service under this warranty, contact Quirky at
866-5-QUIRKY or questions@quirky.com and a Quirky
represent ative will prov ide instruc tion on how to pro ceed.
This warranty shall be null and void if Quirky determines
that the product has been improperly installed, altered
or tamper ed with in any way. Th is warranty d oes not
protect against normal use, wear and tear, or damage due
to abuse.
THIS WARRANTY CONTAINS THE SOLE WARRANTY
OF QUIRK Y. THERE ARE NO OTHER WARR ANTIES,
EXPRESSED OR IMPLIED, INCLUDING THE IMPLIED
WARRANTY OR CONDITION OF QUALITY,
MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE , AND SUCH IMPL IED WARRANTIES , IF
ANY, ARE LIMITED I N DURATION TO THE TER M OF
THIS WARRAN TY. IN NO EVENT SHAL L QUIRKY
BE LIABLE FO R INCIDENTAL, SPEC IAL, DIRECT,
INDIRECT O R CONSEQUENT IAL DAMAGES SUCH A S,
BUT NOT LIMIT ED TO, LOST BUSINES S OR PROFITS
ARISING O UT OF THE SALE OR US E OF ANY QUIRK Y
PRODUCT, EVEN I F ADVISED OF THE PO SSIBILIT Y OF
SUCH DAMAGES.
Some jurisdictions do not allow exclusions or limitations
on implied warranties or incidental, consequential or other
damages, so the above exclusions and limitations may not
apply to you.
COPYRIG HTANDTRAD EMARKNOTICE S
©2014 Qu irky, Inc. All r ights reser ved.
Quirky is a registered trademark of Quirky, Inc.
Wink is a trademark of Wink, Inc.
GE is a registered trademark of General Electric Company
and is under license by Quirky, Inc.
Wi-Fi is a registered trademark of the Wi-Fi Alliance.
ZigBee is a registered trademark of ZigBee Alliance.
Apple and iTunes are registered trademarks of Apple, Inc.
App Store is a service mark of Apple, Inc.
Android and Google Play are trademarks of Google, Inc.
SUPPORT
Need help?
Email questions@quirky.com
Call 1- 866-5 QUIRKY
• Switches can be used to turn standard
or smart bulbs on or off
• Programmable features within the Wink app
allow switch es to dim smart bul bs
• Tapt can trigger other smart products with
one touch (e.g., Push one of its buttons when
you wake up to ope n all of your smart b linds,
adjust th e smart thermo stat to a desired
temperature, and turn on smart light bulbs)
• Switches allow you to schedule standard
bulbs to turn o n/off
RINSTAPTWH|rev
INVENTED BY
Michael Taylor
INFLUENCERS
Tapt was invented by Michael Taylor,
a business analyst from Canton, GA.
An energy-conscious dad of three,
Michael was constantly following
his kids around to make sure they
turned off lights, TVs, and ceiling fans.
He came up with Tapt so he could
manage his household at a glance.
These days, you’re likely to find
Michael practicing taekwondo,
running a Spartan race, or listening
to Weird Al Yankovic.
PART # : R-INS -TAPT-WH02
SPEC : 100gsm brig ht white C2S , Matte UV
FLAT DIMS : 22 0 x 336 mm
FINIS HING : Z-fold both ways
PANTONE
115 C
INSTALLATIONINSTRUCTIONS
Open the Wink app on your mobile
device and log i n with your email
address an d password. If this is
your first tim e using the Wink app,
tap Sign Up to cre ate an account.
Follow the steps p rovided in the
Wink app.
The white LED ligh ts on the
buttons will blink when pairing. The
pairing mode will last 60 seconds.
To restart the pai ring mode, press
and hold both b uttons on Tapt at
the same tim e for 5 seconds. The
lights will start blinking.
When the Wink app displays
“success,” your d evice is
connected . The white LED light on
the top right of e ach button will be
solid ON when paired, then turn
off aer a few second s.
1 Turn OFF power at th e circuit breaker that
controls the li ght switch. It is recomme nded
to use a circuit teste r to make sure the circuit
is off.
2 Remove existing w all plate and light switch.
3 Identify the line, load, ground and neutral
wires. IF TH ERE ARE NO NEUTRAL WIRES ,
STOP AND CONSULT AN ELECTRICIAN .
4 If neutral is present, disconnect the wiring
from the existing switch.
5 Connect Tapt assembly wiring with included
push-in wire connectors. A push-in wire
connector works as a ‘finger trap’ for wires;
simply pus h wires into an available pole to l ock.
Connect a s follows:
GREEN wire on switch to green/bare GROUND wire
WHITE wire on switc h to white NEUTRAL wire
BLACK wire on switch to black LI NE wire
RED wire on switch to r ed LOAD wire
NOTE: Your home’s wiring may diff er;
please consult an electrician.
6 Double- check to confirm wiring is correct.
7 Place Tapt assembly into wall and mount using
the mounting screws from the existing switch.
8 Use the included faceplate or attach your
existing wall plate:
To use the included faceplate:
Press the faceplate onto the snap plate.
To use your existing w all plate:
Unscrew the sm aller top and bottom screws
on the assembly and remove the snap plate.
Attach your wa ll plate only.
NOTE: The included f aceplate and snap plat e
are intende d for single gang box in stallations
only. If install ing in a double gang box , use a
double gang wall plate (not included) without
the faceplat e and snap plate.
9 Turn on power at the circu it breaker.
10 There is a wh ite LED light on the top right
of each switch button that will turn on when
pressed. P ress each button to make sure
Tapt is wired correct ly.
11 I f the lights are not workin g, be sure to turn
off power at the circ uit breaker before you
fix the wiring.
CONNECTINGTAPTTOTHEWINKAPP
Tapt should be in stalled by a qualifie d electrician an d used in accordance wit h appropriate elec trical codes and reg ulations.
This is a sin gle pole switch and neu tral connection i s required. Not inten ded for replacement o f 3-way switches.
Loading...