Quinetic QUDB, QUBP User guide

QUDB

Quinetic

Doorbell Receiver

Installation Instructions

QUBP

Quinetic

Bell Push Button

Product Description:

The Quinetic doorbell adopts wireless kinetic micro-energy collection
and self-powered technology. The QUBP bell push button requires no
battery and is maintenance-free.

The QUDB receiver is compatible with QUBP bell push button and the
QUPIR Quinetic PIR. The QUBP and QUDB doorbells are not compatible
with other Quinetic switches and controlling receivers.

QUDB Doorbell receiverQUBP Bell Push button

Specifications:

∙ Operating Voltage: AC220V-240V 50/60Hz
∙ Power Supply: Self-Powered
∙ Communication: RF 433MHz
∙ Modulation: FSK
∙ Working Range: 80m* (outdoor) / 30m* (indoor)
∙ Volume Level: 4 levels
∙ Ringtones: 38 songs
∙ Temperature Range: Push button (-25°C~+55°C)

Doorbell Receiver (-10°C~ + 55°C)
∙ Storage Capacity: ● The receiver can be paired with up to
10 bell push buttons

● One push button can be paired with an
unlimited number of receivers

*Di stance c omes fr om Quin etic la borat ory tes t resul t. The ac tual di stanc e in prac tical

use mi ght var y due to en viron menta l diffe rence .

Installation: Doorbell Receiver Key Description:

1. Plug the doorbell receiver directly into the electrical socket
and it will ring once after the power is on. This product is suitable
for indoors use only. Please avoid using it in high temperature,
high humidity, dusty, and strong electromagnetic interference
environments. (It is recommended to install it above 50cm from
the ground, otherwise the signal will be weakened.)

Volume key: Pres this key and the volume will
switch between levels 1-4.

Ringtone selecon key +: Press this key to cycle
through the available ringtones.

Ringtone selecon key -/Pairing buon: Used for
pairing and changing the ringtone to the previous
one.

Pairing Method:

1. For single or multiple bell push buttons pairing or if the bell
push needs to be paired with the doorbell receiver again follow the

2. Use screws to install the QUBP fixing part. Tear off the 3M sticker
on the back of the bell push and then paste it on the fixing part.
(Do not stick on a metal door, otherwise it will affect the signal.)

steps below:

Pairing

Button

-+-+-

QUPIR

a. Press the ringtone selection key - for 3
seconds until the light is flashing, then release
the button.

b. Press the bell push once and the light will
go off. This means that the pairing is successful.

(If multiple doorbell receivers or bell pushes
need to be paired repeat the above steps.)

c. QUPIR pairing Instructions:
Follow a. above then press and hold the pairing
button on the PIR sensor for 3 seconds and the
green LED sensor indicator will start flash slowly.
Release the button and the PIR sensor enters

+

pairing mode. Press the pairing button on the PIR
sensor once, and the indicator on the doorbell
receiver will stop flashing. This means that the
pairing is successful.

2. For multiple bell push buttons pairing with a single doorbell
using multiple ringtones follow the steps below:
a. Press the ringtone selection key + first and choose the desired
ringtone.
b. Press the ringtone selection key - for 3 seconds until the light
is flashing, then release the button.
c. Press the corresponding bell push once and the light will
go off. This means that the pairing is successful.
d. Use the above steps for pairing with other bell push buttons.

Doorbell Receiver Clear Pairing:

Press the ringtone selection key - for 12 seconds
until the light changes from flashing to still to off.
The button can then be released.
Once done all pairing information is cleared down.

Power cut memory

After a power cut the doorbell memorises the last set ringtone
and ring volume.

Night Light Mode

The QUDB Quinetic doorbell receiver can be used as a night light.
Once the doorbell receiver is installed in place and it is set to night
light it will not work as a doorbell anymore. The bell push will act
as a wireless switch and can be installed near the bed or in other
convenient locations.

1. Press the ringtone selection key - for 6 seconds
until the light changes from flashing to still and then
release the button. The night light mode is on.

2. To turn off the night light mode to restore the
doorbell function press the music selection key -
for 6 seconds, then release the button when the
light is still.

QUDB - Product dimensions: QUBP - Product dimensions:

*For more informaon about pairing,
instrucons and troubleshoot please
visit www.tlc-direct.co.uk website.