Quickie Xenon Directions For Use Manual

1

Directions for use

690675.01

Xenon

2

For visually impaired people, you will nd information on our website
(www.SunriseMedical.com).

3

Foreword

Dear Customer,

We are very pleased that you have decided in favour of a
high-quality SUNRISE MEDICAL product.

This Owner’s manual will provide numerous tips and
ideas so that your new wheelchair can become a
trustworthy and reliable partner in your life.

Maintaining close ties to our customers means a lot to us
at Sunrise Medical. We like to keep you up-to-date about
new and current developments at our company. Keeping
close to our customers means: fast service, as little red
tape as possible, working closely with customers. When
you need replacement parts or accessories, or if you just
have a question about your wheelchair – we are there for

you.

We want you to be satisfied with our products and
service. At Sunrise Medical we are constantly working to
develop our products further. For this reason, changes
can occur in our palette of products with regard to form,
technology, and equipment. Consequently, no claims can
be construed from the data or pictures contained in this
owner’s manual.

The management system of SUNRISE MEDICAL is
certified to DIN EN ISO 9001, ISO 13485 and ISO

14001.

As the manufacturer, SUNRISE MEDICAL,
declares that the lightweight wheelchairs
conform to the 93/42/EEC 2007/47/EEC
guideline.

Please contact your local, authorised SUNRISE
MEDICAL dealer if you have any questions regarding the
use, maintenance or safety of your wheelchair.

In case there is no authorised dealer in your area, or you
have any questions, contact Sunrise Medical either in
writing or by telephone.

Sunrise Medical Limited
High Street Wollaston
West Midlands DY8 4PS
England
Tel.: [phone]
www.sunrisemedical.com

IMPORTANT:

DO NOT USE YOUR WHEELCHAIR UNTIL
THIS MANUAL HAS BEEN READ AND
UNDERSTOOD.

Use

Wheelchairs are exclusively for a user who is unable to
walk or has limited mobility, for their own personal use,
when self-propelling and being moved by a third party
(pushed by attendant) within the home and outdoors.

The maximum weight limit (includes both the user
and any weight of accessories fitted to the
wheelchair) is marked on the serial number label,
which is affixed to the cross-brace or the stabilising
bar under the seat.

Warranty can only be issued if the product is used under
the specified conditions and for the intended purpose.
The expected life of the wheelchair is 5 years.
NO NON-STANDARD PARTS are to be fitted, other than
those officially approved by Sunrise Medical.

Area of Application.

The variety of options as well as the modular design
means that it can be used by those who cannot walk or
have limited mobility because of:

• Paralysis

• Loss of extremity (leg amputation)

• Extremity defect/deformity

• Joint contractures/joint injuries

• Illnesses such as heart and circulation deficiencies,
disturbance of equilibrium or cachexia as well as for
elderly people who still have strength in the upper body.

When considering provision, please also note the body
size, weight, physical and psychological constitution, the
age of the person, living conditions and environment.

4

Table of Contents

3.1 Denitions of words used in this manual

Word Definition

DANGER!

Advice to the user of Potential Risk
of serious injury or death if the
advice is not followed

WARNING!

Advice to the user of a potential risk
of injury if the advice is not followed

CAUTION!

Advice to user that potential
damage to equipment may occur if
the advice is not followed

NOTE: General advice or best practice

The wheelchair is not designed to be
a seat during transportation.

Reference To Additional
Documentation

NOTE:

Please keep a note of your local service agent’s address
and telephone number in the space provided.
In the event of a breakdown, contact them and try to give
all relevant details so they can help you quickly.

Dealer signature and stamp

Definitions

Foreword 3
Use 3
Area of Application. 3
Table of Contents 4
Denitions 4
General Safety Notes and Driving Limits 5
Guarantee 7
Wheelchair components 8
Handling 9
Quick Release Wheels 10
Options - Step Tubes 10
Options - Brakes 10
Footboard 12
Options – Seat 14
Options - Castors 16
Options - Backrests 17
Options - Wheel Alignment 18
Options - Side-guards 19
Options - Push Handles 20
Options - Crutch Holder 21
Options - Anti-Tip Tubes 21
Options - Stabilising Bar 22
Options - Transit Wheels 22
Options - Pelvic Restraint Belt 23
Options - Pelvic Restraint Belt continued 24
Daily Checks 25
Tyres and Mounting 25
Maintenance and Care 25
Troubleshooting 26
Disposal / Recycling of Materials 26
Nameplate 27
Technical Specications 27
Torque Settings 32

NOTE:

The wheelchairs shown and described in this user guide
may not correspond in every detail exactly to your own
model. However, all instructions are completely relevant,
regardless of possible detail differences.
The manufacturer reserves the right to alter without
notice any weights, measurements or other technical
data shown in this manual. All figures, measurements
and capacities shown in this manual are approximate,
and do not constitute specifications.

5

General Safety Notes and Driving Limits

WARNINGS!

The construction of this wheelchair, as well as the
technology used, are designed to give the maximum level
of safety. International safety standards currently in force
have either been fulfilled or exceeded in parts.
Nevertheless, users may put themselves at risk by
improperly using their wheelchairs. For your own safety,
the following rules must be observed.

Unprofessional or erroneous changes or adjustments
increase the risk of accident. As a wheelchair user, you
are also part of the daily traffic on streets and pavements,
just like anyone else. We would like to remind you that
you must comply with any relevant traffic laws and
pedestrian restrictions.

Be careful during your first ride in this wheelchair. Get to
know your wheelchair.

Before each use, the following should be checked:

• Quick-release axles on the rear wheels

• Velcro on seats and backrests

• Tyres, tyre pressure, and wheel locks.

Before changing any of the adjustments of this
wheelchair, it is important to read the
corresponding section of the Owner’s manual.

WARNINGS!

Maximum weight limit: 125 kg. Please note the •
weight information for lighter weight options,
which are quoted separately.

This wheelchair should be used exclusively to convey •
one person at a time. Any other use does not comply
with the intended purpose.
Your wheelchair has not been designed for •
transportation in a vehicle. DO NOT sit on the
wheelchair during any transportation in a vehicle;
always use a properly secured vehicle seat!!
Your wheelchair is not designed to be a seat during •
transportation.
Only permanently installed seats and safety belts will •
offer sufficient protection in hazardous situations.
When vehicles are in motion, unoccupied wheelchairs •
should be secured using appropriate means.
Before changing any of the adjustments of this •
wheelchair, it is important to read the corresponding
section of the Owner’s manual.
It is possible that potholes or uneven ground could •
cause this wheelchair to tip over, especially when
riding uphill or downhill (Fig. A).
When riding over a step or up an incline frontally, the •
body should be leaning forward, (Fig. A).

DANGER!

Secure your wheelchair on uneven ground or when •
transferring (e. g. into a car) by using the brakes.
For thigh amputees you must position the rear wheels •
towards the back and/or use anti-tip tubes.
With active centre of gravity adjustment, the •
wheelchair may tip over, so anti-tip tubes should be

used.

This product has been tested to a maximum speed of •
10kph. At higher speeds, depending on the
configuration and/or physique/physical capabilities of
the user, there may be unexpected castor wobble.
This can lead to injury of the user.
Before setting off, check that your tyre pressure is •
correct. The correct tyre pressure is printed on the
edge of the wheel, for rear wheels it should be at
least 3.5 bar (350 kPa).
All brakes will only work if there is sufficient tyre •
pressure and if the correct setting has been made
(see the Chapter on "Brakes").

Fig. A

6

DANGER!

The wheel locks are not intended to brake your
wheelchair whilst it is moving. They are only there to
ensure that your wheelchair does not begin rolling away.
When you stop on uneven ground/floors, you should
always use the wheel locks to prevent such rolling.
Always apply both wheel locks; otherwise, your
wheelchair could tip over.

CAUTION!

The wheel locks have not been designed to be used as
brakes for a moving wheelchair.
Always make use of elevators and ramps. If these are not
available, you should request the help of an attendant.
They should only grip the wheelchair at securely mounted
parts. If anti-tip tubes are fitted these must be folded
away. A wheelchair should never be lifted with an
occupant; it should only be pushed.

DANGER!

Do not lift or carry the wheelchair by the backtubes or •
the pushhandles.

If the seat and back sling are damaged, you must •
replace them immediately.

Be careful with fire, in particular with lighted •
cigarettes, seat and back slings can catch fire. seat
and back slings can catch fire.

To avoid injuries to the hand when operating the •
wheelchair, grip between the rear wheel and the
brake.

Always make sure that the quick-release axles on the •
rear wheels are set properly. If the button on the
quick-release axle is not pressed in, the rear wheel
cannot be removed.

DANGER!

In particular when using lightweight metal handrims, •
fingers will easily become hot when braking from a
high speed or on long inclines.
If the wheelchair is subject to direct sunlight for a long •
period of time, then parts of the wheelchair (e.g.
frame, legrests, brakes and side guard) may become
hot (>41°C).

WARNINGS!

When using the chair outside, always wear leather •
gloves which will increase your grip and protect the
fingers from dirt and overheating.
The effect of the brake as well as the general driving •
characteristics are dependent on tyre pressure. The
wheelchair is significantly lighter and easier to
manoeuvre when the rear wheels are pumped up
correctly and both wheels have the same pressure.
Make sure that your tyres have sufficient tread!•
Please note that you are subject to any and all traffic •
laws when driving in public traffic.
Before using the wheelchair for the first time, the user •
must receive the necessary instruction.
When it is dark, please wear light clothing or clothing •
with reflectors, so that you can be seen more easily.
Make sure that the reflectors on the side and back of
the wheelchair are clearly visible. We would also
recommend that you fit an active light.
Do not use the wheelchair on slopes > 10°.•
Do not use the wheelchair on muddy or icy ground.•
Only use the wheelchair in areas which are permitted •
for pedestrians.
When working with or making adjustments to your •
wheelchair, be careful not to get your fingers caught!

Operating conditions:

The wheelchair can be used indoors as well as outdoors
on dry, relatively smooth surfaces.

WARNING!

The wheelchair should not be used in heavy rain, snow,
slippery, or unsound surfaces.
Do not use the wheelchair in hazardous environments.

7

Guarantee

Guarantee

THIS DOES NOT AFFECT YOUR LEGAL RIGHTS IN
ANY WAY.

Guarantee conditions

1) Repair or replacement is carried out by the authorised
Sunrise Medical dealer.

2) To fulfil the guarantee conditions, should servicing
need to be carried out on your wheelchair under this
agreement, contact the designated Sunrise Medical
customer service agent immediately, with precise details
on the type of difficulty. Should you be using the
wheelchair outside the area covered by the designated
Sunrise Medical customer service agent, the work will be
carried out under "guarantee conditions" by another
agency as designated by the manufacturer.

3) Should a part or parts of the wheelchair require repair
or replacement within 24 months (5 years for frame and
cross-brace) after transfer of ownership to the original
purchaser, and provided that this person is still the owner
of the wheelchair, as a result of a specific manufacturing
or material defect, the part or parts will be repaired or
replaced free of charge if the wheelchair is returned to
the authorised customer service agent.

Note: This guarantee cannot be transferred.

4) The guarantee also covers all repaired or replaced
parts for the remaining period of the guarantee for the
wheelchair.

5) For spare parts which are fitted after the start of the
original guarantee, we give a further 24-month
guarantee.

6) Consumable parts are normally excluded from the
guarantee, except in the case that premature wear of the
part is the direct result of a manufacturing fault. These
parts include, amongst others, upholstery, tyres, inner
tubes and similar parts.

7) The guarantee conditions above cover all product
parts for models which were purchased at full sales price.

8) Normally we do not accept responsibility if a repair or
replacement of the wheelchair is required for one of the
following reasons:

a) The product or part has not been maintained or
serviced in accordance with the manufacturer's
recommendations as shown in the User Instructions and/
or the Service Instructions. Accessories have been used
which are not specified as original accessories.

b) The wheelchair or a part of the wheelchair was
damaged through neglect, accident or improper use.

c) Alterations to the wheelchair or parts, which are not in
accordance with the manufacturer's specifications or the
carrying out of repairs before informing the customer
service agent.

8

1. Push handles

2. Back sling

3. Sideguard

4. Seat sling

5. Footrest

6. Castors

7. Footboard

8. Fork

9. Quick-release axle

10. Wheel locks

11. Handrim

12. Rear wheel

13. Folding bracket

Wheelchair components

3

1

4

2

13

5

7

8

6

10

12

9

11

3

Fig. B

9

Handling

Folding up

First remove the seat cushion from the wheelchair and
flip up the (platform) footplate. Take hold of the sling or
the seat tubes (Fig. 1) in the middle, from the back, and
pull it upwards until the folding bracket (Fig. 2) clicks into
place.

Transport

To move the mobility aid, the folded wheelchair should be
lifted by holding the front part of the cross-brace and the
push handles.

Unfolding

Push the release lever of the folding bracket (Fig. 3)
downwards and push both frame halves apart. Then
press on the seat tube (see figure). Your wheelchair is
then unfolded. Now snap the seat tubing into position in
the seat saddle. This can be facilitated by slightly tipping
your wheelchair to the side, as this means that the weight
is taken off one of the rear wheels. Be careful not to get
your fingers caught in the cross-tube assembly. Fit
the seat cushion. (Fig. 4).

Getting into your wheelchair on your own (Fig.5)

• Push the wheelchair to a wall or a solid piece of
furniture;

• Apply the brakes;

• Flip the footplates up;

• The user can lower themselves into the wheelchair;

• Fold the foot plates back downwards and position your
feet in front of the heel loops.

Getting out of your wheelchair on your own (Fig.6)

• Apply the brakes;

• Fold the footplates upwards with your foot;

• With one hand on the armrest, the person should bend
slightly forward, to bring the body weight to the front of
the seat, and then with both feet firmly on the ground
and one foot behind the other, push up into the upright
position.

Fig. 1

Fig. 6

Fig. 5

Fig. 4

Fig. 3

Fig. 2

10

Quick Release Wheels

Quick-release axles on rear wheel

The rear wheels are equipped with quick-release axles.
The wheels can then be fitted or removed without using
tools. To remove a wheel, simply depress the quick­release button on the axle and pull the wheel off the axle.
(Fig. 7).

CAUTION!

Hold the quick-release button on the axle depressed
when inserting the axle into the frame to mount the
rear wheels. Release the button to lock the axle in
place. The quick-release button should snap back to
its original position.

Options - Step Tubes

Step tubes are used by attendants to push a wheelchair
over an obstacle. Simply step on the tube to push a
wheelchair, for example, over a kerb or step, (Fig.8).

Options - Brakes

CAUTION!

Braking power can be
affected by incorrect fitting and
adjustment of the brakes, as well as tyre pressure which is
too low.

Wheel locks
Your wheelchair is equipped with two wheel locks. They
are applied directly against the tyres. To engage, press
both brake levers forward against the stops. To release
the locks, pull the levers back to their original positions.

Braking power will decrease with:

• Worn tyre tread

• Tyre pressure that is too low

• Wet tyres

• Improperly adjusted wheel locks.

The wheel locks have not been designed to be used as
brakes for a moving wheelchair. The wheel locks should
therefore never be used to brake a moving wheelchair.
Always use your hands for braking. Make sure that the
gap between the tyres and wheel locks complies with
given specifications. To readjust, loosen the screw and set
the appropriate gap. Then re-tighten the screw
(Fig. 9 and 10).

CAUTION!

After each adjustment of the rear wheels, check the wheel
lock gap and re-adjust if necessary.

3.0mm

Fig. 10

Fig. 9

Fig. 8

Fig. 7

11

Brake Lever Extension

The longer lever helps to minimise the effort needed to set
the wheel locks.
The brake lever extension is screwed to the brakes. By
raising this, it can be flipped forward. (Fig. 11).

CAUTION!

Mounting the wheel lock too close toward the wheel
will result in a higher effort to operate. This might
cause the wheel lock extension lever to break!

WARNING!

Leaning onto the brake lever extension while transferring
will cause the lever to break! Splashing water from tyres
might cause the wheel lock to malfunction.

Compact Brakes

Compact brakes are underneath the seat sling and are
operated by pulling the brakes towards the rear, in the
direction of the tyre. For the brakes to operate correctly,
they must be pulled fully against the stops, (Fig.12).

CAUTION!

Incorrect mounting of the wheel lock will result in a higher
effort to operate.
This might cause the brake lever extension to break!

Drum Brakes

Drum brakes permit safe and convenient braking for an
attendant.
They can also be applied with the aid of a locking lever
The locking lever must snap audibly into place.
Performance of the drum brakes is not dependant on the
air pressure inside the tyres.
The wheelchair cannot be pushed when the drum brakes
are set.

WARNING!

Drum brakes should only be adjusted by authorised

dealers.

Fig. 11

Fig. 12

Fig. 13

12

Footrests

Various footboards are available on the Xenon. These
can flipped up to make it easier to transfer to/from the
chair. They are described individually.

Lower leg length

By undoing the clamp screw (Fig.14), you can adjust the
lower leg length. Loosen the clamp screw, adjust the tube
with the footboard to the desired position.
Tighten clamp screws again (see the page on torque).
Ensure that the plastic push joint is located under the
clamp screw in the correct position.

WARNINGS!

Do not stand on the footboard! Even if the user is •
sitting in the chair, there is still a risk of tipping over
and injury.
When transferring, do not stand on the footboard, •
there is a risk of tipping over and injury.

Platform Footrests

The footplates can be flipped up to make it easier to
transfer to and from the chair.
The footplates can also be tilted to six different angles
relative to a level surface.
Tighten screw (1) firmly on the outer side.
By removing the clips (2), the footrest can be adjusted
to three different positions toward both the front and rear.
Loosen the adjustment screw (3) to change the horizontal
position of the footboard.
For this purpose, the footboard must be flipped up,
(Fig.15, 16, & 17).
When finished, make sure that all screws have
been properly tightened (see the page on torque).
A minimum interval of 2.5 centimetres from the ground
should always be maintained.

Fig. 14

Fig. 15

Fig. 16

Fig. 17

13

Width adjustment of footrests

If the footrest width needs to be adjusted, please undo
the screw (1), set the desired width, by positioning 1, 2 or
3 spacers (2) from outer to the inner side and then refit
the screws, (Fig.18).

Lightweight footrest

The footboard angle can be adjusted by loosening the
screws (2). Side protection panels can be fitted to the
footboard using the mounting holes (3) These prevent the
feet slipping off accidentally, (Fig.19). Make sure that
after any adjustment work, all screws are tightened
correctly (see the page on torque).

Width adjustment

To adjust the width of the footboard open the screw (2).
Then you can slide in and out the tubes in the holder to
adjust the width of the footboard (Fig.19).
Please make sure that the screws are tightened with the
correct torque .

Automatic folding footrest

The footrest angle can be adjusted by loosening the
screws (1) and turning the footrest. When tightening,
please note the torque measurements, (Fig.20).

High-mount footrest

The high-mount footrest is fitted on the inner part of the
frame and permits a higher position than a standard
footrest (Fig. 21)

Fig. 19

2

2

3

3

Fig. 21

Fig. 20

1

Fig. 18

1

2

14

Options – Seat

Seat sling

Use the Velcro straps under the sling to tighten/loosen the
seat sling.

Adjusting the seat height

To change the seat height, please release the Allen
screws (1) with an Allen key. Take the axle bracket (2) out
of the axle stem (3) and remove or add the spacer (4).
Then refit the axle bracket (2) into the axle stem (3) and
re-tighten the screws (1), (Fig.22 & 23).
Tighten the 2 Allen screws to 7 Nm (Fig. 22).

NOTE:

An adjustment to the castor angle may be necessary
when adjusting the rear seat height.

COG Setting

To carry out COG adjustment, there are basically 2
different options. Fine adjustment can be carried out
directly on the axle bracket, as this has an asymmetrical
shape. By turning it, you can achieve different settings. To
make an adjustment in larger steps, you must change the
position of the whole axle stem on the frame.

Changing the axle stem

Using the quick-release axles, take the wheels out of the
angle adapter.

Undo both screws (1) and remove these completely. Fit
the axle stem in the desired position on the frame, put the
screws back into the perforated plate and then re-tighten
the screws. When moving the axle stem, also move the
seat saddle on the frame, (change the axle stem and the
seat saddle). Make sure that the left and right sides are
fitted in the same positions. Use the given torque of 7 Nm
(Fig. 24/25).

Fig. 22

1

Fig. 23

2

3

4

1

Fig. 25

1

Fig. 24

15

Rotate the axle bracket (Standard)

Using the quick-release axles, take the wheels out of the
angle adapter.

Undo the screws (1) and remove the axle brackets (2) on
both sides of the wheelchair. Rotate the axle bracket by
180° and refit it into the axle stem (3) on the opposite
side. Please note that the axle bracket has an
asymmetrical shape. The adjustment offers changes in
the centre of gravity in 2 cm steps. Use the given torque
(Fig. 26/27).

In addition, the standard adapter offers a second position
for fitting the angle adapter. When the wheelchair is
delivered, this position is covered with a sleeve. To use
this position, please undo the two screws (1). Then swap
the axle adapter (4) and the sleeve (5) and re-tighten both
Allen screws (1), (Fig. 26/27). Please note that the key
surfaces on the axle adapter should always point inwards
and select the wheelbase as desired (see width
adjustment of the rear wheelbase). Use the given torque.
For centre of gravity adjustment, please see the technical
specifications section at the end of these Directions for

use.

Rotate the axle bracket (lightweight)

Using the quick-release axles, take the wheels out of the
angle adapter.

Undo the screw (1) and remove the axle brackets (2) on
both sides of the wheelchair. Rotate the axle bracket by
180° and refit it into the axle stem (3) on the opposite
side. Please note that the axle bracket has an
asymmetrical shape. The nut surface (4) must always
face outwards. The adjustment offers changes in the
centre of gravity in 2 cm steps. Always use the given
torque (Fig. 28/29).

Fig. 26

1

Fig. 27

2

3

4

5

Fig. 28

1

Fig. 29

2

3

4

16

Options - Castors

Setting the Castor, Castor adapter & Castor
fork

If the wheelchair veers slightly to the right or left, or the
castors flutter, it may be caused by one or more of the
following:

• Forward and/or reverse wheel motion has not been set

properly.

• The castor angle has not been adjusted properly.

• Castor and/or rear wheel air pressure is incorrect; the
wheels do not turn sufficiently freely.

The optimum adjustment of the castors is required so that
the wheelchair runs in a straight line.
Castors should always be adjusted by an authorised
dealer. The castor plates must be re-adjusted, and the
wheel receiver must be checked every time the rear wheel
position has been altered.

Adjusting the castor

To ensure that both forks are set parallel, simply count the
teeth visible on both sides. After setting the castor fork,
the teeth will guarantee a secure position, allowing an
adjustment of 16° in 2° increments, (Fig. 30).
Use the flat side on the front of the castor fork to check for
a right-angled position to the ground.

The patented design allows the castor fork to be turned,
so that it can be reset at right-angles to the ground when
the seat angle is changed.

Setting the directional stability

Release the Allen screws (1) on the underside of the fork.
You can then remove the screws (2). You can now turn
the black socket (3) left or right.
Left – chair pulls to the left
Right – chair pulls to the right
Then re-tighten the screw (2). Please set a 90° angle from
the fork to the floor.
Then re-tighten the screw (1). (Fig. 31).

Fig. 31

2

3

1

+8° - 8°

Fig. 30

17

Options - Backrests

To adjust the back angle, please undo the Allen screw (1)
and remove it. Set the desired position and then refit the
screw in this position and tighten it to the given torque
(Fig. 32).

Folding backrest

To make it easier to transport the wheelchair, the top half
of the backrest can folded down.
To do this, press both levers (1) and fold the backrest
down. When folding the backrest back up, please make
sure that both sides are firmly interlocked (Fig. 33/34)

Adjustable back sling

The adjustable back
sling can be adjusted for tension by using several straps.
The back sling upholstery can be accessed from the
inside via an opening and can be padded to suit individual
tastes, (Fig.35).

Fig. 32

1

Fig. 33

Fig. 35

1

Fig. 34

1

18

Options - Wheel Alignment

Adjusting the wheel alignment

NOTE: To achieve the very best movement, the rear

wheels must be adjusted to their optimum position, which
means correctly adjusting the wheel alignment. To do this,
measure the distance between both wheels front and rear
to ensure that they are parallel to one another. The
difference between both measurements should not
exceed 5 mm. The parallel setting can be adjusted by
loosening the screws (1) and rotating the axle adapter (2).
When finished, make sure that all screws have been
properly tightened, (Fig.36). See the page on torque.

WARNING!

Be careful, there is a risk of tipping when adjusting the
centre of gravity of the seat!

Adjusting the rear wheelbase width

The rear wheelbase is defined as the distance between
the upper side of the rear wheels and the backrest tubes
and is factory set (1.25 cm). This must be increased if
more space is to be created between the tyres and the
optional height-adjustable armrests.

NOTE: When adjusting the rear wheelbase, set first one
wheel and then the other. When adjusting the rear
wheelbase, move the axle adapter (3) in a telescopic
manner into the axle bracket (2) or out of the camber
tube. Loosen the screw (1) on the rear axle bracket. Move
the axle adapter in or out, until the desired wheelbase is
achieved. Tighten the screws to 7 Nm. Repeat
the procedure on the right side of the wheelchair and set
the same gap on the left side, (Fig. 36 - 37).

Fig. 30

Fig. 37

Fig. 36

1

2

1

2

3

19

Options - Side-guards

1. Fitting
a. Push the outer armrest rails down into the receiver
which is mounted on the wheelchair frame.
b. The armrest will automatically lock into place.

2. Height adjustment
a. Turn the release lever for height adjustment (2) to the
second stop point.
b. Push the armpad up or down to reach the desired
height.
c. Set the lever back to the interlocked position against
the armrest rails.
d. Push the armpad (4) until the rails click into place
securely.

3. Remove the armrest
a. Operate the lever 3 and lift the whole arm.

4. Insert armrest
a. Put the armrest back in the receiver, until the arm clicks
into place.

Mounting Components For The Armrest
Receiver

Adjusting the armrest receiver
To tighten or loosen the fit of the outer armrest rails in the
receiver:

1. Loosen the four set screws for the receiver (D) on the
sides of the receiver.

2. Leave the armrest in the receiver (E) and push the
receiver together, until the desired adjustment is achieved.

3. Tighten the four screws (D). (144 in-lbs, 16.3 Nm)

Position adjustment

1. Loosen the two clamp screws (10) until the clamp is

loose.

2. Push the armrest receiver to the desired position.

3. Tighten.
(Fig.38, 39, 40 and 41).

1. Outer armrest rails

2. Height adjustment of the locking lever

3. Locking lever

4. Armrest pad

5. Transfer bar

6. Side-guard

7. Receiver

8. Adjustment clamp

9. Parts to adjust the receiver

10. Clamp screws

Fig. 39

Fig. 40

Fig. 41

1

E

Fig. 38

1

2
3

6

4
5

9

7

20

Options - Side-guards (continued)

Side-guard with clothes protector

The clothes protector prevents clothes getting dirty from
spray water, (Fig.42).
You can set the position in relation to the rear wheel by
moving the side-guard.
To do this, remove the screws (1 and 2).
After setting to the desired position, re-tighten the screws
(see the page on torque).

WARNING!

Neither the side-guards nor the armrests are to be used
for lifting or carrying the wheelchair.

Options - Push Handles

Height-adjustable push handles

These handles are secured with pins to prevent them from
sliding out unintentionally. By releasing the tension lever
(1) the height of the push handles (2) can be set
individually. If the lever is moved, listen to make sure that
it clicks into place. The push handle can easily be set to
the desired position. The nut on the tension lever
determines how tightly the push handles are clamped into
place. If the nut is loose after adjusting the tension lever,
the push handle will also be too loose. Turn the push
handle from side to side before use to make sure that it is
clamped into place securely. After adjusting the handle
height, always clamp the tension lever (1) securely into
place. If the lever is not secure, injuries could result when
ascending stairs. (Fig. 43).

CAUTION!

If the height-adjustable push handles are not fitted
properly, there is a risk that these will develop "play" or
that they move out of position. Please make sure that the
relevant screws are tightened correctly.

Folding push-handles

If the folding push handles are not required, they can be
flipped downwards by pushing the button (1). When they
are required again, flip the push handles up, until they
click into place. (Fig. 44).

Fig. 42

1

2

Fig. 43

1

2

Fig. 44

1

21

Options - Crutch Holder

Crutch holder

This device permits crutches to be transported directly
on the wheelchair. It has a Velcro loop to fasten
crutches or other aids.

WARNING!

Never try to use or remove the crutches or other aids
while moving.

Options - Anti-Tip Tubes

WARNING!

Sunrise Medical recommends anti-tip tubes are fitted for
all chairs.
When fitting anti-tip tubes, use a torque of 7 Nm.

Anti-tip tubes prevent the wheelchair from tipping
backwards, providing additional safety for new users and
for users familiarising themselves with the operation of the
wheelchair.

Plug in Type

Slotting the anti-tip tubes into the clamp

Press the rear button on the adapter for the anti-tip •
tube in such a way that both release pins are pulled
inwards.
Slot the anti-tip tubes (1) into the anti-tip tube adapter.•
Rotate the anti-tip tubes downwards, until the release •
pin clicks into place in the clamp.
Fit the second anti-tip tube in the same way.•

Adjusting the anti-tip tubes

To achieve the correct ground clearance of approximately.
1“ to 2“ (2.5 cm to 5.0 cm), the anti-tip tubes must be set
higher or lower:

Push the release lever for the anti-tip tube in such a •
way that both release pins are pulled inwards.
Move the inner tube upwards or downwards in the •
height-adjustment holes.
Release the button. •
Fit the second anti-tip tube in the same way. •
Both wheels must be at the same height. (Fig. 46).•

.

Fig. 45

Fig. 46

Fig. 47

1

1

Swing-away Type

Push down on the top of the anti-tip tube, (1), to bring
them into position, (Fig.47).
A 30 - 50 mm gap should be maintained between the
anti tip wheels and the ground.
The anti-tips can also be swung into a forwards
position. The anti-tips must always be in the forward
position when negotiating large obstacles, (such as
kerbs), to prevent them from interfering with the
manoeuvre.

DANGER!

If the anti-tip tubes are not fitted, or have been fitted
incorrectly, there is a risk of tipping over and of injury.

22

Options - Stabilising Bar

Folding stabilising bar

This bar is used to stabilise the backrest. To be able to
fold the wheelchair, the release lever must be pushed
inwards (Fig. 48) or released and the stabilising must be
flipped downwards.
When unfolding the wheelchair, please make sure that the
stabilising bar is locked into position.

Options - Transit Wheels

Transit wheels

Transit wheels should be used whenever your wheelchair
would be too wide if the rear wheels were fitted, (Fig.49).
After the rear wheels have been removed with the aid of
the quick-release axles, the transit wheels can
immediately be used to continue riding, (fig.50).
The transit wheels are mounted so that they are
approximately 3 cm above the ground when not in use.
They are therefore, out of the way when riding,
transporting, or when tipping to pass over obstacles,
(Fig51).
Make sure that the transit wheels are always mounted in
position "B".
This will ensure that the wheelchair has a stable base,
(Fig52).

DANGER!

Without rear wheels, your wheelchair has no wheel •
locks.
There is a risk of the chair tipping backwards.•

Fig. 48

Fig. 49

Fig. 50

Fig. 51

Fig. 52

B

23

Options - Pelvic Restraint Belt

WARNINGS!

Before using the wheelchair make sure that the pelvic •
restraint belt is fitted.
The pelvic restraint belt must be checked on a daily •
basis to ensure it is free from any obstruction or

adverse wear.

Always make sure that the pelvic restraint belt is •
correctly secured and adjusted prior to use.

DANGER!

If the strap is too loose, this could cause the user of the
wheelchair to slip down and risk suffocation or serious
injury.

The pelvic restraint belt is fitted to the wheelchair as
shown in Fig. 53 to 58. The seat belt comprises two
halves. They are fitted using the existing seat stay
retaining bolt fitted through the eyelet on the belt. The belt
is routed under the rear of the side panel. (Fig. 53).

Adjust the pelvic restraint belt to suit the user’s needs as
follows:

Adjust the belt position so buckles are in the centre of the
seat. (Fig. 54).

Feed free belt back through male buckle and slide
adjusters.
Ensure belt is not looped at male buckle, (Fig.55).

Feed free belt through slide adjusters and male buckle to
provide more belt length, (Fig.56 to 58).

Fig. 53

Fig. 54

Fig. 56

Fig. 57

Fig. 55

Fig. 58

24

Options - Pelvic Restraint Belt continued

When fastened check space between the pelvic restraint
belt and user. When correctly adjusted it should not be
possible to insert more than the flat of the hand between
the pelvic restraint belt and the user, (Fig. 59).

The pelvic restraint belt should be fixed so that the belt
sits at an angle of 45 degrees across the user's pelvis.
The user should be upright and be as far back as possible
in the seat when correctly adjusted. The pelvic restraint
belt should not allow the user to slip down in the seat,
(Fig. 60).

To fasten buckle:

Firmly push male buckle into female buckle, (Fig.61).

To release buckle:

Press the RED button in the centre of the buckle then pull
the two halves gently apart, (Fig.62).

NOTE: If you have any questions on the use and
operation of the pelvic restraint belt, the please contact
your wheelchair dealer, carer or attendant.

WARNINGS!

The pelvic restraint belt must only be fitted or adjusted •
by an approved Sunrise Medical dealer / agent.
The pelvic restraint belt must be checked on a daily •
basis to ensure it is adjusted correctly and free from
any obstruction or adverse wear.
Sunrise Medical does not recommend the •
transportation of a person in a vehicle with the pelvic
restraint belt as a restraint system.

See the transit brochure from Sunrise Medical for
further information on transportation.

Maintenance:

Check pelvic restraint belt, and securing components, at
regular intervals for any sign of frays or damage.
Depending on usage, it may need to be replaced.

WARNING!

The pelvic restraint belt should be adjusted to suit the end
user as detailed above Sunrise Medical also recommends
that the length and fit of the belt is checked on a regular
basis to reduce the risk of the end user inadvertently
re-adjusting the belt to an excessive length.

Fig. 59

Fig. 60

Fig. 61

Fig. 62

25

Daily Checks

CAUTION!

As the user, you are the first person to notice any possible
defects. We therefore recommend that before each use,
you check the items in the following list:

Check for correct tyre pressures•
Check that the brakes work correctly•
Check that all removable parts are secure, e.g. •
armrest, footrest, quick-release axle etc.
Check for visible damage e.g. on the frame, backrest, •
seat sling and back sling, wheels, footplate etc

If there is any damage or malfunction, please contact your
authorised dealer.

Tyres and Mounting

WARNING!

Always make sure that you maintain the correct
tyre pressure (min. 3.5 bar) as this can have an effect on
wheelchair performance.

If the tyre pressure is too low, rolling resistance will
increase, requiring more effort to move the chair forward.
Low tyre pressure also has a negative impact on
manoeuvrability.

WARNING!

If the tyre pressure is too high, the tyre could burst.

The correct tyre pressure for a given tyre is printed on the
surface of the tyre (min. 3.5 bar).
Tyres can be mounted the same way as an
ordinary bicycle tyre.
Before installing a new inner tube, you should
always make sure that the base of the rim and interior of
the tyre
are free of foreign objects.
Check the pressure after mounting or repairing a tyre
. It is critical to your safety
and to the wheelchair’s performance that
regulation air pressure be maintained and
that tyres are in good condition.

Maintenance and Care

Check the tyre pressure every 4 weeks. •
Check all tyres for wear and damage.

Check the brakes approximately every 4 •
weeks to make sure that they are working
properly and are easy to use.

Change tyres as you would an ordinary •
bicycle tyre.

All of the joints that are critical to using your •
wheelchair safely are self-locking, nyloc
nuts. Please check every three months to
make sure that all bolts are secure (see the
section on torque). Nyloc nuts should only
be used once and should be replaced after

use.

Please use only mild household cleansers •
when your wheelchair is dirty. Use only soap
and water when cleaning the seat sling.

If your wheelchair should ever get wet, •
please dry it afterwards.

A small amount of sewing-machine oil •
should be applied to quick-release axles
approximately every 8 weeks.

Depending on the frequency and type of •
use, we recommend taking your wheelchair
to your authorised dealer every 6 months to
have it maintained by trained personnel.

CAUTION!

Sand and sea water (or salt in the winter) can damage
the bearings of the front and rear wheels. Clean the
wheelchair thoroughly after exposure.
The following parts can be removed and sent
back to the manufacturer/dealer for repair:

• Rear wheels:

• Armrest

• Footrests

• Anti-Tip Tubes

These components are available as spare
parts. For further information,please see the
spare parts catalogue.

26

Maintenance and Care continued

Hygiene measures when being re-used:

Prior to the wheelchair being re-used, it must be carefully

prepared.

WARNING!

All surfaces which come into contact with the user must
be treated with a disinfection spray.
To do this, you must use a disinfectant from the DGHM
list, e.g. Antifect Liquid (Schülke & Mayr) for rapid alcohol­based disinfection for medical products and medical
devices, which must be disinfected quickly.
Please take into account the manufacturer's instructions
for the disinfectant you are using.
In general, a complete disinfection cannot be guaranteed
on seams. We therefore recommend that you dispose of
seat and back slings to avoid microbacterial contamination
with active agents according to § 6 infection protection

law.

Troubleshooting

Wheelchair pulls to one side

• Check tyre pressure

• Check to make sure wheel turns easily (bearings, axle)

• Check the castor angle

• Check to make sure both castors are making proper
contact with the ground

Castors begin to wobble

• Check the castor angle

• Check to make sure all bolts are secure; tighten if
necessary (see the section on torque)

• Check to make sure both castors are making proper
contact with the ground

Wheelchair / cross-tube assembly does not snap into
position in the seat saddle

• Chair is still new, i.e., the seat or backrest upholstery is
still very stiff. This will improve with time.

Wheelchair is difficult to fold up

• Adjustable backrest upholstery is too stiff. Loosen it
accordingly.

Wheelchair squeaks and rattles

• Check to make sure all bolts are secure; tighten if
necessary (see the section on torque)

• Apply small amount of lubrication to spots where
movable parts come in contact with one another

Wheelchair begins to wobble

• Check angle at which castors are set

• Check tyre pressure

• Check to see if rear wheels are adjusted differently.

Disposal / Recycling of Materials

NOTE: If the wheelchair has been made available to you

as part of a charity or medical loans scheme, then it may
not belong to you . If it is no longer required, then follow
the instructions to return it as given by the organisation
that made the wheelchair available to you.

In the following section, there is a description of the
materials used on the wheelchair, in view of the disposal
or recycling of the wheelchair and its packaging.
There may also be special local regulations in force with
regard to disposal or recycling, these must be taken into
account when disposing of your wheelchair. (This can
include the cleaning or decontamination of the wheelchair
prior to disposal).

Aluminium: Castor forks, wheels, chair sideguards,
armrest frame, footrest, push handle

Steel: securement points, quick-release axle
Plastic: Handles, tube stoppers, castors, footplates,

armpads and tyres
Packaging: Plastic bags made of soft polyethylene,
cardboard
Upholstery: Polyester fabric with PVC coating and highly­flammable foam.

Disposal or recycling should be carried out by a disposal
company or at a public disposal point. You can also return
your wheelchair to your dealer for disposal.

27

Nameplate

The nameplate is located on either the cross-tube
assembly or the transverse frame tube, as well as on a
label in the owner’s manual. The nameplate indicates the
exact model designation and other technical
specifications. Please provide the following pieces of
information whenever you have to order replacement
parts or to file a claim:

• Serial number

• Order number

• Month/Year

Technical Specifications

Overall width:

With standard wheels including hand rims, close mount:

• in combination with aluminium side guard:

SW + 170 mm

• in combination with plastic clothes protector:

SW + 190 mm

• With extra-narrow hand rim fitting, overall width is
reduced by 20 mm.

• With standard wheels including hand rims and 4°
camber: SW + 250 mm
Overall length:
910 mm with SD 480 mm

Overall height:

1120 mm with BH 450 mm

Folded dimensions:

• with rear wheels approximately 270 mm

• without rear wheels approximately 250 mm

Weight in kg:

• Overall from 8.5kg

• Transportation (without footrest, wheels, side guard) 6kg

• Side guard (unit) 1.3 kg

• Wheels (unit) 2.2 kg

530mm

1050mm

805mm

970mm

28

Technical Specifications continued

Maximum weight limit:

Xenon up to a load of 125 kg

Seat heights:

The choice of frames, forks and castors as well as the
size of the rear wheel (610mm (24")), (635mm (25"));
determines what seat heights are possible.

Table of Minimum and Maximum Values

Parameter Min. Max. Parameter Min. Max.

Overall length
with footrest

770 mm 1050 mm Seat surface

angle

0° 15°

Overall width 620 mm 760 mm Effective seat

depth

340 mm 500 mm

Folded length N/A N/A Effective seat

width

320 mm 460 mm

Folded width 270 mm 310mm Seat height at the

front edge

430 mm 570 mm

Folded height N/A N/A Backrest angle 75° 108°

Total weight 8.5 kg 13.0 kg Back height 250 mm 475 mm

Weight of
the heaviest
individual part

- 2.1 kg with 610mm
(24") rear wheel

Distance from
the footrest to the
seat

220 mm 520 mm

Static stability ­downhill

10° 10° Angle from leg to

seat

92° 100°

Static stability

- uphill (with anti­tip tube)

10° 10° Distance from the

armrest to the
seat

N/A N/A

Static stability -

sidewards

10° 10° Front position of

the armrests

N/A N/A

Dynamic stability

- uphill power
consumption

N/A N/A Handrim diameter 540 mm 567 mm

Overcoming
obstacles

N/A N/A Horizontal axle

position

+ 30 mm + 13 mm

The wheelchair conforms to the following standards:

1. Requirements and test methods for static, impact and fatigue strengths (ISO 7176-8)

2. Flammability resistance of upholstered parts in accordance with ISO 7176-16 (EN 1021-1/2)

29

Technical Specifications continued

Castor Fork Type of frame Front seat height

in mm

Rear seat height
in mm

76mm (3")

98 mm x 32 mm

low

430 430 - 400
440 440 - 400

450 450 - 390

high

470 470 - 380
480 480 - 380
490 490 - 380

111 mm x 32 mm

low

440 440 - 400

450 450 - 390
460 460 - 380

high

480 480 - 380
490 490 - 380

500 500 - 400

102mm (4")

98 mm x 32 mm

low

440 440 - 390

450 450 - 380
460 460 - 380

high

480 480 - 380
490 490 - 380

500 500 - 390

111 mm x 32 mm

low

450 450 - 380

460 460 - 380
470 470 - 380

high

490 490 - 380
500 500 - 380
510 510 - 370

111 mm x 45 mm

low

450 450 - 390

460 460 - 380
470 470 - 380

high

490 490 - 380
500 500 - 380
510 510 - 370

123 mm x 45 mm

low

450 450 - 390

460 460 - 380
470 470 - 380
480 480 - 380

high

490 490 - 380
500 500 - 380
510 510 - 390
520 520 - 400

30

Technical Specifications continued

Castor Fork Type of frame Front seat height

in mm

Rear seat height
in mm

127mm (5")

98 mm x 32 mm

low

460 460 - 380
470 470 - 380

high

500 500 - 380
510 510 - 390

111 mm x 32 mm

low

460 460 - 380
470 470 - 380
480 480 - 380

high

500 500 - 380
510 510 - 390
520 520 - 400

111 mm x 45 mm

low

470 470 - 380
480 480 - 380

high 510 510 - 390

520 520 - 400

123 mm x 45 mm

low

470 470 - 380
480 480 - 380
490 490 - 380

500 500 - 380

high

510 510 - 390
520 520 - 400
530 530 - 410
540 540 - 420

152mm (6") 123 mm x 45 mm

low

500 500 - 380
510 510 - 390

high

540 540 - 420
550 550 - 430

31

Technical Specifications continued

Castor Fork Type of frame Front seat height Rear seat height

76mm (3")

FROGLEG

low

480 480 - 380
490 490 - 380

500 500 - 380

high

520 520 - 400
530 530 - 410
540 540 - 420

102mm (4")

FROGLEG

low

490 490 - 380

500 500 - 380
510 510 - 390

high 530 530 - 410

540 540 - 420
550 550 - 430

127mm (5")

FROGLEG

low 510 510 - 390

520 520 - 400

high

550 550 - 430
560 560 - 440

152mm (6")

FROGLEG

low 530 530 - 410

high 570 570 - 450

Centre of Gravity Matrix

32

Torque Settings

7 Nm

7 Nm

7 Nm

7 Nm

7 Nm

7 Nm

NOTE: If no specific torque information is given, the generic torque value for M6 screws is 7.0 Nm

33

NOTES

Dealer signature and stamp

34

Dealer signature and stamp

NOTES

35

Dealer signature and stamp

NOTES

Sunrise Medical GmbH & Co. KG
69254 Malsch/Heidelberg
Germany
Tel.: [phone]
Fax: [phone]
www.sunrisemedical.com

Sunrise Medical Limited
High Street Wollaston
West Midlands DY8 4PS
England
Tel.: [phone]
www.sunrisemedical.com

Sunrise Medical S.L.
Polígono Bakiola, 41
48498 Arrankudiaga – Vizcaya
España
Tel.: [phone]
Fax: [phone]
www.sunrisemedical.es

Sunrise Medical S.A.
13, Rue de la Painguetterie
37390 Chanceaux sur Choisille
France
Tel.: [phone]
Fax: [phone]
www.sunrisemedical.com

Sunrise Medical Srl
Via Riva 20, Montale
29100 Piacenza (PC)
Italy
Tel.: [phone]
Fax: [phone]
www.sunrisemedical.it

Sunrise Medical A.G.
Lückhalde 14
3074 Muri bei Bern
Switzerland
Tel.: [phone]
Fax: [phone]
www.sunrisemedical.ch

Sunrise Medical AS
Rehabsenteret
1450 Nesoddtangen
Norway
Tel.: [phone]
Faks: [phone]
www.sunrisemedical.no

Sunrise Medical AB
Britta Sahlgrens gata 8A
42131 Västra Frölunda
Sweden
Tel: [phone]
Fax: [phone]
www.sunrisemedical.se

Sunrise Medical B.V.
Pascalbaan 3
3439 MP Nieuwegein
Netherlands
Tel.: [phone]
Fax: [phone]
www.sunrisemedical.com

M.M.S. Medical Ltd.
Forge Hill Cross, Kinsale Road
Cork
Ireland
Tel.: [phone]
Fax: [phone]

G2 A/S
Graham Bells Vej 21-23 A
8200 Arhus N
Denmark
Tel.: [phone]
Fax: [phone]
www.G2.dk

OM_Xenon_EU_EN_Rev.1.0_09_12_2010