NFC Manager
User Manual
The software NFC-Manager offer the possibility to write, read and format NFC-Tags very easily. Further
you can transfer data to a suitable Android mobile via a direct P2P (Peer to Peer) connection.
The NFC-Manager can write Tags in a way that the following actions are executed on your mobile
phone automatically:
Choice of a certain URL (webpage)
Display of a v-card
Dial a phone number
Send a SMS (short message service)
Part of NFC Development Kit, CONRAD Best.-Nr. 001082694
NFC Manager User Manual
2
Firmware
Driver
Date(Version)
2012.7.10 or higher
2012.4.6 (1.4.0.0) or higher
CONTENTS
1. Introduction ................................................................................................................................................................................. 2
2. List of NFC Tag(IC Type) ...................................................................................................................................................... 3
3. NFC Tag Basics ........................................................................................................................................................................ 3
4. NFC Manager ............................................................................................................................................................................ 4
5. Tag Detect ................................................................................................................................................................................... 5
6. Tag Format .................................................................................................................................................................................. 6
7. Tag Write...................................................................................................................................................................................... 7
8. Tag Read .................................................................................................................................................................................. 13
9. P2P Write ................................................................................................................................................................................. 15
10. P2P Read ................................................................................................................................................................................. 17
1. Introduction
This manual has been written for keeping in mind the end-user who uses NFC Manager Program.
In this manual is explained how to use NFC Manager Program without any difficulty or troublesome. It
describes the various functions that will be provided in the application. The purpose of this document is to
give detail description about NFC Manager Program.
Firmware and Driver
Version : 2.0
3
NXP Mifare Classic 1k
NFC Forum Type 1
Innovision Topaz IRT5011
NFC Forum Type 2
NXP
Mifare Ultralight
Mifare Ultralight C
NTAG203
INFINEON
my-d NFC SLE 66R01P
my-d NFC SLE 66R32P
Kovio 2k (K14T1)
NFC Forum Type 3
Sony FeliCa
NFC Forum Type 4
NXP Mifare DESFire EV1
ISO/IEC 14443 standard series, full compliant cards
2. List of NFC Tag(IC Type)
List of NFC Tag(IC Type) supported by NFC Manager Program
NFC Manager User Manual
3. NFC Tag Basics
NFC Manager Program reads and writes NDEF data onto a Tag.
To read/write, a NFC Tag must be initialized. This program initializes NFC tag (IC Type) only on the above
list (Refer to 2. List of NFC Tag(IC Type)).
NFC Manager provides P2P communication between DUALi’s NFC device and Android NFC mobile.
It has been providing Android NPP (NDEF Push Protocol) and SNEP (Simple NDEF Exchange Protocol)
will be also possible in near future.
Version : 2.0
4
4. NFC Manager
<NFC Manager main>
NFC Manager User Manual
<Connect>
NFC Manager Program finds automatically NFC Device (produced by DUALi only), when it is
connected.
Version : 2.0
5
5. Tag Detect
When a Tag is placed on NFC Device, it reads the information on the Tag.
< Mifare Classic as NFC Type Tag Detect>
NFC Manager User Manual
<NFC Forum Type 1 Tag Detect>
Version : 2.0
NFC Manager User Manual
6
IC Type
Capability Container
NDEF Data
NFC Forum Type 1
Topaz IRT5011
0xE1101000
0x0300FE00
(NDEF TLV/
Terminate TLV)
NFC Forum Type 2
Mifare Ultralight
0xE1100600
Mifare Ultralight C
NTAG203
0xE1101200
my-d NFC SLE 66R01P
0xE1101000
my-d NFC SLE 66R32P
0xE110FE00
Kovio 2k (K14T1)
0xE1100700
NO
NFC Forum Type 3
Sony FeliCa
Ln byte in the Attribute
Information Block is 0h
NO
NFC Forum Type 4
ISO/IEC 14443-4
NO
0x0003D00000
6. Tag Format
When formatting a Tag, this program writes the data listed on the below table on Capability Container (or
Attribute Information), and NDEF Data.
(NO: no data )
1. Click “Format Tag”
Version : 2.0
7
2. Place a Tag on the device
3. Following message will be show when Format is done
NFC Manager User Manual
The below message will be shown when unsupported tag (Refer to 2. List of NFC Tag(IC Type))
is on the device
7. Tag Write
NFC Manager Program provides 5 types of below record
- TextRecord
- UriRecord
- SmartPosterRecord
- VCardRecord(vCard)
- AndroidApplicationRecord
Version : 2.0
8
7.1 Add Record
<Text Record> Input TEXT you want to add and click add button
NFC Manager User Manual
To delete text/url/Sp/vCard data, double click it from the log box
<Uri Record> Input URI / URL you want to add and click add button
Version : 2.0
NFC Manager User Manual
9
<Smart Poster Record> Input Smartposter data you want to add and click add button
<Bookmark> Input Bookmark you want to add and click add button
<Call Request> Input Phone number you want to add and click add button
Version : 2.0
NFC Manager User Manual
10
<SMS> Input message you want to add and click add button
<VCard Record> Input business card information you want to add and click add button
Version : 2.0
11
7.2 Write a Tag
1. After adding Record, click “Tag” on the lower- right hand side and “Write NDEF”
NFC Manager User Manual
2. Place a Tag on the device.
Version : 2.0
12
3. This message will pop up when writing a Tag is succeeded
NFC Manager User Manual
4. An error message will be shown in case of failure.
Version : 2.0
NFC Manager User Manual
13
5. Following message will be shown when the size of NDEF Messages is bigger than Tag memory
size.
8. Tag Read
1. Click “Tag” on the lower- right hand side and “Read NDEF”
Version : 2.0
14
2. Place a Tag on the device.
NFC Manager User Manual
3. Following message will be show when you place a tag on [Read] windows.
Version : 2.0
15
9. P2P Write
1. According to “8.1 Add Record”, add Record.
Click “P2P” on the lower- right hand side and “Write NDEF”
NFC Manager User Manual
2. Place a NFC-enabled Android mobile on the device.
Perhaps you have to confirm it on your smartphone.
Version : 2.0
NFC Manager User Manual
16
3. This message will pop up when writing a Tag is succeeded.
4. An error message will be shown in case of failure.
Version : 2.0
17
10. P2P Read
1. Click “Tag” on the lower- right hand side and “Read NDEF”
NFC Manager User Manual
2. Place a NFC-enabled Android mobile on the device.
Version : 2.0
18
3. Following message will be show when you place a tag on [Read] windows.
NFC Manager User Manual
4. The below message will be shown when an NFC unsupportable mobile is on the device.
Version : 2.0
Loading...